Line Fault Indicators
See Also: Overhead Line
-
Product
PXI 10A Fault Insertion Switch 10-Chan 2-Bus
40-199-002
Fault Insertion Unit
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
Product
Fault Locating
-
Schweitzer Engineering Laboratories, Inc.
The built-in fault-locating methods in SEL devices allow you to quickly identify faults, dispatch crews for repairs, and restore service faster. Traveling-wave fault-locating technology calculates the locations of temporary and permanent faults by measuring the arrival times of the naturally occurring traveling waves caused by a transmission line fault. Accurately detecting these waves requires ultra-high-resolution monitoring, and locating is accurate to within one tower span (±300 m). Impedance-based fault-locating technology calculates fault locations by detecting changes in line impedance as a result of a fault. Impedance-based locating is reliable and accurate to about 2 percent of a line’s total length.
-
Product
Square Root - Gauge Line Error Indicators
-
Parker PGI's SRE6 and GLE6 Indicators are designed to quantify Square Root and Gauge Line Errors in natural gas orifice flow measurement. They identify inaccuracies caused by compressor-induced pulsation and differential pressure discrepancies.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Cable Indicators
CableTroll
-
They are installed on Ring Main Units in distribution substations. They are used to detect short circuit and earth faults, and can be installed on most types of cable terminations. Some units will give separate indications for short circuit and earth faults, locally by flashing diodes and remotely through separate relay contacts or additional ComTroll communications modules.
-
Product
Sound Level Indicators
-
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, a sound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site.An important attribute to consider when searching for a suitable sound level meter is its type or class. The type or class of a sound level meter defines the device's accuracy as per American National Standards Institute (ANSI) or International Electrotechnical Commission (IEC) guidelines. Typically, "type" is the grade according to the ANSI S1.4 standard, whereas "class" is the grade according to the IEC 61672 standard. There are two types or classes assigned to sound level meters: type 1 / class 1 or type 2 / class 2. For assessing noise in basic industrial, commercial, educational, recreational or residential applications, a type 2 / class 2 sound level meter usually will suffice. For precision-grade assessments often made in a laboratory, a type 1 / class 1 sound level meter primarily is used. PCE sound level meter products are lightweight, easy-to-use and manufactured in accordance with the highest industrial standards.
-
Product
Indicators
-
Choose from a wide range of indicators designed for high accuracy and high speed applications for the processing industries. PENKO’s range includes sophisticated products that are suitable for general use in trade applications including automatic and non-automatic weighing applications. Our indicators are designed with easy and comfortable operation in mind. A screen with good visibility, an intuitive operating panel and a quickly obtained stable weighing signal are all part of our high-performance indicators. The precision weighing capability also ensures reliable and accurate measuring information.
-
Product
Microwave Delay Line
E501
-
The Eastern OptX Series E501 / Microwave Delay Line is a high performance turnkey solution for radar and communications market. The E501 allows for ultra wide bandwidth, low loss, high isolation and immunity from EMI and EMP with timedelays up to 250 usec at frequencies up to 18 GHz.
-
Product
Visual Fault Locators
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
Joinwit Visual Fault Locators
-
Product
Cable Fault Finder
-
Techno Instrumentation (India) Private Limited
Magnetic and Acoustic signal strength through bar graph and digits on LCD.Coincidence feature gives distance to the fault in milliseconds.Easy, fast and accurate pinpointing of faults.
-
Product
Indicators - Dial
-
Used for precise comparisons or measurements of workpiece surfaces, machine, equipment, part tolerances, alignment.
-
Product
AC Line Splitter
1937
-
Peaceful Thriving Enterprise Co Ltd
The AC line splitter is a helpful testing device for electrician. Electrician can measure the current with clamp meter through the X1 and X10 measuring rings. X1 is 1:1 measurement, and X10 is ten times (1:10) of the actual current, which is helpful for small current measurement. This device also combines the function of socket tester and GFCI tester, which means electrician can use this tester to test socket and load at the same time.
-
Product
Fault Location
REFLEKT
-
REFLEKT makes fault location more efficient, effective and practicable than ever before, even on complex networks.
-
Product
Line Protection
-
Schweitzer Engineering Laboratories, Inc.
SEL transmission line protection relays provide subcycle line differential and multizone distance protection for a secure, reliable, and high-speed solution. Their fault-locating capabilities allow you to efficiently dispatch line crews to quickly isolate line problems and restore service faster.
-
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-194A-001
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Detection of PtG and PtP Faults in Line Networks
LineTroll 110Tμr
-
The indicator is powered by replaceable long-life lithium batteries which have a life expectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
Synchro and Resolver Angle Indicator
AIT5
-
Computer Conversions Corporation
This series of units were designed to satisfy Hi speed synchro/resolver applications where the output data must be fresh and no data staleness can be tolerated. The tranducers utilized are the same as in the regular MDS series, however different tracking electronics are used. The resultant data tracks the input shaft perfectly and is always fresh and accurate at input speeds up to 64 revolutions per second, depending on the resolution. Data in BCD or Binary formats are available, and clean, unambiguous crossovers are guaranteed.
-
Product
Equipment Condition Indication
MetalSCAN
-
Condition indication in real-time, so you can schedule maintenance at the right time.MetalSCAN is the leading real-time, on-line condition indication technology designed to alert equipment operators to bearing and gear damage, long before equipment failure. Nothing else comes close. Its advanced capabilities deliver knowledge that transforms equipment failure to predictable and avoidable high cost events. Use MetalSCAN to optimize maintenance schedules, reduce repair costs, increase reliability and improve safety.
-
Product
Speed Indication & Sensing
-
Provide an accurate speed display at an economical cost. Available with Digital or Analog displays in both a panel and base-mount enclosure. Each maintains the reliability and rugged performance customers expect.
-
Product
Bluetooth Smart Digital Indicators
-
• Integrated data transmission• Robust construction• Water and coolant resistant• New technology with configurable menus• Broad choice of functions (MIN/MAX/DELTA, TOL, Factor, PRESET, AUTO OFF, etc.)• Automatic wake-up and sleeping mode (S.I.S system), absolute System*• Maximum error of 3 μm
-
Product
Single Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-201
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Visual Fault Locator
VFL X5003
-
Constant & stable output powerLow battery warning, reminds users to change the battery timely.Long battery life (up to 40 hours with AAA batteries)Pocket size and light weight, easy to use.Re-changeable ceramic tube, to avoid returning to manufacturer for this small fault.
-
Product
Voltage Indicators & Detectors
-
Digital Voltage Detector is designed for easily indicating AC voltage on Underground primary, Over head primary and Transmission conductors up to 999 kV. The large digital display can be seen and read at distances up to 50'. Unit is perfect for large system voltages from 4kV to 765kV Phase to Phase.
-
Product
Knopp Phase Sequence Indicator
K-3, K-6, and K-7
-
Use of the Knopp K-3 Phase Sequence Indicator saves man-hours and protects valuable equipment against damage. It pays for itself in a short time. Specially designed induction motor unmistakably indicates the phase sequence by direction of rotation or rotor disc.
-
Product
Coking Coal Indices Determinator
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
Is used to determine the plastometric indices of bituminous coal (maximum thickness of plastic layer Y, final contraction value of plastic layer X) and describe technical characteristics of coke, which helps to guide coking and coal blending . It is widely applied in coal mining, metallurgy, chemical industry and verification institution of coal quality.
-
Product
Panorama Line Solutions
ASYMTEK
-
Nordson ASYMTEK designs automated conformal coating line solutions to fit your production process. Every Panorama™ line we build, includes the right balance of equipment and process control for optimal coating efficiency.
-
Product
Acoustic Fault Detector
AFL212-AMD
-
K&S Engineering and Scientific Ltd
This compact acoustic headset, designed and manufactured by K&S Engineering and Scientific Ltd has been developed with state-of-the-art components to not only to achieve superior performance but also to offer the user an acoustic headset that is smaller than equivalent units currently available on the market. Housed in an IP67 enclosure, the unit, which is used in conjunction with a high voltage surge generator, can easily contend with wet conditions.
-
Product
Visual Fault Locators
-
Optical Wavelength Laboratories
OWL fiber optic visual fault locators (VFL) are specially designed to couple a maximum of optical energy into multimode and singlemode optical fibers by using a bright red fiber optic laser. Breaks, microbends, and other anomalies in optical fibers and connectors cause the intense bright red laser light to escape, thus revealing the presence of a fault. In addition to visual fault location, OWL VFLs can be used as a visual optical fiber identifier. A visual fiber optic identifier eliminates much of the guesswork during testing by identifying the fiber under test.
-
Product
Cable Fault Locators
-
Wuhan Sunma Technology Co., Ltd.
Visual Fault Locator, we can understand its function in the letter. It could be regarded to be part of OTDR and the fiber fault locator is cheap. Fiber visual fault locator is a kind of device which is able to locate the break-point, bending or cracking of the fiber glass. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. Designed with a FC,SC,ST universal adapter, this fiber testing red light is used without any other type of additional adapters, it can locates fault up to 10km in fiber cable. SunmaFiber also supply a new kind of Cable Fault Locator, Fiber laser tester/ fiber laser pen, it can locates fault up to 30km in fiber cable. Contact us at Sales@SunmaFiber.com or Live Chat with us. Save your money & time right now! Buy from fiber optic supplies at SunmaFiber.com with your confidence.
