Beta Testing
prior release testing to assure almost final product fulfills requirements
See Also: Development
-
Product
Memory Test System
T5851/T5851ES
-
The T5851 system is designed to provide a cost-effective test solution for evaluating high-speed protocol NAND flash memories including UFS3.0 universal flash storage and PCIe Gen 4 NVMe solid-state drives (SSD), both of which are expected to be in high demand for the LTE 5G communications market.
-
Product
Fully-Automated CTIA-Compliant OTA Test System
TS8991
-
The R&S®TS8991 OTA performance test system measures the spatial radiation and sensitivity characteristic as specified by CTIA and 3GPP.The system software provides ready-to-use test templates for OTA measurements and supports all wireless standards.The integrated report function collects all measured test data such as graphics or numeric results, test environments, EUT information and hardware setup in one document.
-
Product
Positioning Test System
TS-LBS
-
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131G
-
The Keysight 85131G is a 53 cm (21 in) long1 semi-rigid cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 4 inch radius. Stability1 of the Keysight 85131G is 0.06 dB and phase is 0.16o * f + 0.5o (where f is frequency in GHz).
-
Product
Antenna Test System
ATS1000
-
Offering measurements on active and passive devices - supporting also extreme temperature testing. 5G is all about data, speed and reliability using high frequency millimeter wave bands. The lack of conventional external RF connectors makes 5G antenna characterization challenging. 5G antenna, chipset and UE manufacturers as well as wireless market operators need a viable solution for research, diagnostics and debugging up to type approval.
-
Product
Design for Testability (DFT Test)
-
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
Inline test system for FCT, ICT, ISP and Boundary Scan for Automated Operation
LEON InLine
-
High production volume often requires inline solutions with fully automated product Handling – the LEONlnline is a complete Inline Board Test Solutions for printed circuit boards. It integrates a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors.
-
Product
In-Line RF Test Platform
AR925
-
This functional and RF test platform combines outstanding productivity with substantial equipment savings. The Faraday chamber of the fixture comes with an interchangeable cassette to minimize the testing cost of each new product
-
Product
Test Instruments
-
Test instrumentation from COTS to custom, including VXI, PXI and LXI-based platforms.
-
Product
RF Testing Platform for ATx05
AT118
-
The functional test of modern devices with wireless connectivity always requires RF isolated cameras, as the only way to have the parameters controlled and to guarantee operation under the specified conditions.
-
Product
Functional Test Trainer System
QT65
-
Qmax Test Technologies Pvt. Ltd.
Functional Test Trainer system, is a test system which can perform various Power- On functional tests of digital devices(ssl/MSI/LSIs and analog devices in the out- circuit and in-E conditions. Unified Library of vast number of devices to effectively test devices in in-circuit as well as out of circuit conditions.
-
Product
EBIRST 200-pin LFH To 96-pin SCSI Adapter Cable
93-002-226
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
NI's Electrical Functional Test Solution
-
PXI instrumentation ensures complete and accurate test coverage with a modular architecture mounted in ultra-reliable PXI chassis.TestStand and LabVIEW software provide rapid development of complex test steps and sequences. PXI systems conserve floorspace because of their small, light form factor. Order them preassembled and installed using NI ATE Core Configurations.SystemLink™ software deploys updates and democratizes data insights to optimize operational efficiency.
-
Product
Test Platforms
-
Leverage 20+ Years of Test Industry Experience with Built-In IP for Maximum Reuse
-
Product
TestStand
-
TestStand is industry-standard test management software that helps test and validation engineers build and deploy automated test systems faster. TestStand includes a ready-to-run test sequence engine that supports multiple test code languages, flexible result reporting, and parallel/multithreaded test.
-
Product
Functional Test Fixtures
-
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
Product
Functional Test System Optimized For Real-Time Digital Bus Test
Spectrum HS
-
Spectrum HS is Teradyne’s fully integrated functional test system. Optimized for real-time test of low latency buses, it’s a high-performance system delivering excellent test coverage of current and future products.
-
Product
NFC Conformance Test System
T3111S
-
The T3111S RIDER NFC Conformance Test System is the Keysight solution for RF Analog and Digital Protocol testing of NFC, EMV and ISO devices. The Test System is based on the Keysight T1141A NFC Test Set and it is complemented by the Keysight's or FIME's robots for accurate and repeatability RF testing. Selected 3rd party positioning robots can also be supported.
-
Product
6TL08 Benchtop Test Platform
H710008
-
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
Automatic Test System
-
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
-
Product
Communications Test System for Frontline Diagnostics
CTS-2750
-
The CTS-2750 is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The field-upgradeable, software-defined architecture features easy-to-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets can be created easily using the included TestEZ® software suite.
-
Product
2-Module ICT System, I317x Series 6
E9902G
-
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
Product
Dynamic Test Systems
H3TRB | HTGB (HTGS) | RTGB (RTGS)
-
Durability and reliability of wide-bandgap materials such as SiC and GaN are an important topic. The focus here is on new failure mechanisms whose effects are not visible with traditional H(3)TRB/HTGS – but which nevertheless have an influence on the real application.
-
Product
Configurable Functional Test System
ATS-5000
-
Maximize the uptime of your most critical electronics with the ATS-5000 Functional Test System from Astronics Test Systems. Deployed globally for more than 20 years, the newest version of this tester provides a configurable, affordable solution that delivers just enough test.
-
Product
Desktop PCB Test System
BOARDWALKER 9627
-
Qmax Test Technologies Pvt. Ltd.
QT9627 is a cost effective entry level model Desktop PCB Test System. It can be configured to maximum 64 Channels of In-circuit Functional Test Channels and 64 Channels of QSM V-I Signature Test .Maximum Digital Test Speed 10MHz in the QT9627 .
-
Product
EV-DO Analysis Using NI PXI RF Test Instruments
NI-RFmx EV-DO
-
Highly optimized RF measurement experiencePerform physical layer analysis on EV-DO cellular signals including MODACC, ACPR, CHP, OBW, and SEMSimple access to advanced measurement parallelism
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
-
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
-
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
Product
Dielectric Material Test Fixture
16453A
-
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
Product
Iridium Physical Layer Test Systems
PLTS
-
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
