-
Product
Manual Non-Shift Wedge Grips
-
Manual non-shift wedge grips are versatile grips for tensile testing a wide variety of materials, including metals, plastics, and composites. The open-front design allows easy insertion of specimens and exchange of grip faces. The self-tightening action means samples are held firmly within the grip faces, minimizing slippage during testing.
-
Product
Electrical Networks Control System
-
Electrical networks control system is intended for measurements of network electrical resistance and insulation electrical resistance of the tested specimen. The measurement process takes a couple of minutes.
-
Product
Needle Microprobe
MT-23/8HT
-
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Mini Cloud & Pour Point Analyzer
OptiMPP
-
The automated OptiMPP provides highly accurate cloud and pour point results using only 0.5 ml sample. Simply place the sample in a disposable vial into the 20 specimen sample changer and press the OK key. No special programming or expected point is required. Results are available in 20 minutes for a -30ºC pour point.
-
Product
Vibration Monitoring
-
Vibration tests must be safe and reliable and this is especially true for high value specimens in critical aerospace testing applications. Here, m+p Coda offers maximum safety: The monitoring system captures and records data such as acceleration, temperature and strain continuously during vibration tests - irrespective of the vibration control system in use. Each channel can be configured separately for total flexibility.
-
Product
Whole Sole Flexing Tester
SG-P03E
-
Use a cutting tool to pierce the specimen between the cleats at three points along the line of maximum bending stress. By the specified speed and times of 90°bending action to inspect the cuts’ growth with a measuring.
-
Product
Testing of Rear Axle Steering
-
*2 high-precision servo axes for linear load simulation*Communication via CAN / Flexray*Function and noise measurements (NVH)*Supply and discharge of the test specimens via WTs on double belt conveyors*Connection to the production control
-
Product
Martindale Abrasion and Pilling Tester
-
Sataton Instruments Technology CO., Ltd
By providing a defined load, a translational movement tracing a Lissajous figure and abrasive medium, martindale abrasion tester is professional designed for determining of the abrasion resistance of fabrics including specimen breakdown, mass loss and appearance change. The tester can also use to determine the resistance to pilling and surface change of textile fabrics. With accessories, the tester is to determine abrasion resistance of lining and insock for personal protective footwear. It is widely used to evaluate the properties of clothes fabrics, coating materials, wool fabrics, nonwovens and other special materials for protective equipment.
-
Product
Hydraulic Flat Grips
-
These 1 kN pneumatic flat grips are designed for tensile testing metal foils. Unique grip features include a very rigid structure, which reduces swivel of the grip faces during testing, and specially shaped flat grip faces. As with all pneumatic grips, these grips allow quick specimen clamping with a repeatable clamping force.
-
Product
Concrete Bulk Resistivity
RCON
-
Giatec RCON™ is a non-destructive device for measuring the electrical resistivity of concrete specimens in the laboratory without any additional sample preparation requirements. This measurement can easily be made on the same concrete samples that are currently used for the compressive strength testing of concrete.
-
Product
SUNTEST
XXL+
-
Atlas Material Testing Solutions
The Atlas SUNTEST XXL+ is a large xenon lamp weathering and lightfastness test chamber meeting various ISO, ASTM, and ICH industry standards. Its horizontal 3000 cm2 exposure area is best-in-class for 3-D specimen testing.
-
Product
Automatic Contacting Extensometry
AUTOX750
-
The Instron AutoX750 automatic contacting extensometer offers automated, high-precision strain measurement by motor-driven contact arms to engage specimens—eliminating manual setup while maintaining sub-micron accuracy over long travel. They integrate seamlessly with Instron testing frames and software to reduce operator error, speed cycle times, and ensure repeatable, standards-compliant strain data for metals, plastics, composites, and elastomers.
-
Product
X-Ray and CT Inspection
-
Systems offer a microfocus X-ray source, a large inspection volume, high image resolution and is ready for ultrafast CT reconstruction. They cover a wide range of applications, including the inspection of plastic parts, small castings and complex mechanisms as well as researching materials and natural specimens.
-
Product
Generators
Vibration Shock
-
Software Vibration shock is used for testing specimen resistance to vibration impact. This software is a part of the software complex ZETLAB VIBRO, supplied together with vibration control systems ZET 017-U. The software enables generation of impacts with pre-set parameters and noise presence within a specified frequency range. The software is activated via ZETLAB control panel and VCS menu.
-
Product
Multi-Axis Hot Deformation System
MAXStrain
-
The system restrains specimens lengthwise while allowing unlimited deformation in the other two dimensions. As a result, very high strain levels can be introduced into specimens to produce a sample of ultrafine-grain or nanoscale material that is large enough for subsequent properties testing.
-
Product
Averaging Axial Extensometers for Large Compression Samples
Model 3542RA
-
Jinan Testing Equipment IE Corporation
Designed primarily for compressive strength tests on rock, concrete and other large compression samples, this model measures axial strain on opposite sides of the test specimen, and the output is an average of the two readings. Gauge lengths from 1 to 8 inches (25 to 200 mm) and measuring ranges from 0.050 to 0.250 inches (1.2 to 6 mm) are available.
-
Product
Insect Rearing Rooms
-
Standard walk-in incubators or coolers used in the rearing of drosophila and other biological organisms often end up being problematic for a number of reasons. The acids inherent in the rearing of many specimens or their food can quickly corrode a standard refrigeration evaporator. High humidity exacerbates the issue, as droplets of concentrated acid will collect on the cooling components.
-
Product
Heat Seal Tester
HST-01
-
Jinan Leading Instruments Co., Ltd.
HST-01Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated filmsaccording to the requirement of relative standards. The seal parameters includeheat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
Product
Your High-performance Slide Scanner For Fluorescence, Brightfield And Polarization
ZEISS Axioscan 7
-
Digitize your specimens with Axioscan 7 – the reliable, reproducible way to create high-quality virtual microscope slides. Axioscan 7 combines qualities that you would not expect to get in a slide scanner: high speed digitization and outstanding image quality plus an unrivaled variety of imaging modes are all available in a fully automated and easy to operate system.
-
Product
1 KN Eccentric Roller Grips
-
These eccentric roller grips are specifically designed for tensile testing flexible materials, such as rubber and soft and semi-hard plastics. Named after the non-symmetric roller design, these grips employ a simple and quick clamping mechanism. They also have a self-tightening action, which maintains clamping of the specimen during testing regardless of any thickness reduction. In addition, the upper and lower grip faces are parallel grooved to help hold these soft materials.
-
Product
Electrodynamic Vibration Test Systems
CV-series
-
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
Product
Mechanical Wedge Action Grips
2716 Series
-
The Instron mechanical wedge action grips are durable tensile grips designed to automatically increase clamping force as test loads rise, maintaining fixed jaw positions and preventing slippage. Their open-front, moving-body design allows easy specimen insertion while ensuring consistent gauge length and minimal compressive force during clamping, making them a versatile gripping solution and particularly suitable for testing high-strength materials such as metals and composites.
-
Product
SUNTEST
XXL+ FD
-
Atlas Material Testing Solutions
The Atlas SUNTEST XXL+FD is an extra-large light stability test chamber especially tailored towards the needs of consumer goods, food and beverage testing. Its 3000 cm2 flatbed exposure area and tall chamber height is best-in-class for 3-D specimens testing and can accommodate all types of bottles and packaging.
-
Product
Salt Spraying Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is glad to be the ODM/OEM manufacturer of Salt Spraying Chamber,Salt Spray Test Chamber,salt spraying test chamber,Salt spraying chamber,Salt spraying chamber sales enterprises all over the world! 1：It adopts 5mm or 8mm imported gray and white impact resistant P.V.C board, with high temperature resistance up to 85℃ and corrosion resistance. 2：Support frame: ¢ 10MM fiberglass rod, corrosion resistant. The steel V-frame and the fiber rod angle are placed to ensure the specimen is inclined at 15-30 degrees. 3：Pressure barrel is welded seamlessly with 2.0MMSUS304 stainless steel plate 4：The heating adopts titanium alloy electric heating tube. It has high corrosion resistance and long service life is 3-5 years higher than ordinary stainless steel heating tube. 5：The cover is made of 5MM imported transparent (Germany YLIS) acrylic sheet. It has fine workmanship, beautiful appearance and high transparency.
-
Product
5 KN Split-Drum Grips For Rope
-
These lower capacity 5 kN (1,100 lbf) split-drum grips are suitable for testing the tensile properties of rope and string with a diameter of 3 mm (0.12 in) or less. The diameter of the drum in the grips is 50 mm (2.0 in) and a spring mechanism is used to apply a clamping force through the split-drum to the specimen during testing.
-
Product
Fully Automatic Rubber Tensile Testing System
-
Compactly Integrating Functions Required for Quality Control of Rubber Shimadzu Fully-Automatic Tensile Testing System This system provides full automation, from measurement of specimen dimensions, supply to the testing machine, and fixing of chucks to measurement of extension between standard lines and data processing. The system can be used for continuous nighttime testing, which helps save labor costs.
-
Product
Needle Microprobe
MT-29/5HT
-
Fast-response 29 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Screw Side Action Tensile Grips
2710-100 Series
-
The Instron screw side-action tensile grips are precision mechanical grips engineered for tensile testing across a broad spectrum of specimen materials (e.g. metals, plastics, textiles, thin foils) and geometries. Their dual-acting screw mechanism delivers concentric clamping and allows for adjustments to accommodate varying specimen thicknesses or unique components — ensuring reliable load alignment. With quick, tool-free jaw face changes and a wide assortment of interchangeable jaw face types (smooth-ground, serrated, rubber-coated, etc.), these grips offer flexibility in test setup.
-
Product
Drop Weight Impact Testing Machine
DWTT Series
-
Jinan Testing Equipment IE Corporation
DWTT Drop Weight Impact Testing System is suitable for drop weight tear test of various kinds of ferrite, especially for the test of DWTT for pipeline steel as ASTM-E 436, API-RP 5L3, ASTM-E 208 and DIN EN 10274. DWTT has integrated mechanical, electrical, and automatic control technology, and achieved full automation of feeding, hammer lifting impact, and fracture specimen collection. The load frame has a four-column design, features in stable supporting structure, rigid, dual sliding rails. The Drop Weight Drop Weight Tester is equipped with positioning mechanism, anti-dumping mechanism, safety mechanism, hydraulic buffer devices and security guard net. The impact energy is determined by the lifting height and configuration of different net weights. DWTT Drop Weight Impact Testing System is the essential quality control equipment for pipeline manufacturers, steel mills, iron and steel enterprises, and is also widely used for research institutes.1. Buffer device is equipped to avoid the second impact and absorb the residual energy after breaking the specimen so as to prevent the weigher and anvil from destroying. The installation of safety mechanism, buffer device, and security guard net will effectively secure the testing machine and its operation to extend its life.2. Configuration of the specimen-feeding system, anti-second impact device, and specimen centering mechanism will guarantee a quick, accurate and reliable test.
-
Product
High Temperature Testing Mobile Conversion Unit
-
Used for applications that require high temperatures (1800C-2000C) for extended periods of time, the High Temperature Mobile Conversion Unit offers enhanced capabilities to accommodate more damanding requirements.The unit is based on the General Purpose MCU which allows for the use of standard specimen grips and accesories.
