-
Product
Thermal Microscope Stage For Petri Dish
TS-4SMP
-
With our TS-4SMP Thermal Stage for Petri Dish, a specimen on a microscope slide or culture dish can be maintained at any temperature between -20°C and +60°C. Setup is easy, takes little time, and the controller will regulate the stage temperature to within +/-0.1°C. The collar on the stage is designed to accommodate a 35mm 'Nunc' petri dish. The collar may also be removed for use with slides.
-
Product
Dynamic Jack System
-
This is a structural fatigue testing machine for researching the dynamic behavior of full-size or model structures by applying repeated loads. The actuator that supplies the loads to the specimens can be installed on load frames, reaction floors, reaction walls, etc.
-
Product
Taber Type Abrasion Tester
SG-P01T
-
The tester is used for cloth,paper,paints, plywood,leather,tile,glass,rubber etc.The testing method is executed to make specimen abraded by a pair of grinding wheels under the specified load.The weight of abrasion loss is the difference of weight for specimens before and after testing.
-
Product
Needle Microprobe
MT-29/2HT
-
Fast-response 29 gauge needle probe, (needle length is 2cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Impact Tester - Impact Testing Machine
-
Impact tests are used to measure the resistance to failure of materials to a suddenly applied force. The test measures the impact energy, or the energy absorbed prior to fracture. ToronTech™ offers advanced Impact testing machines to measure that energy through drop weigh tear test and Charpy impact test. We also offer machines for the preparation of specimens for these tests.
-
Product
Pin-disc Friction & Wear Testing Machine
WPD-2000
-
Jinan Testing Equipment IE Corporation
WPD-2000 is one type of pin-disc friction wear testing machine. The specimen of metal and non-metal material will be matched to pin shape, disc shape or dual rings to do the test. The pin-disc friction wear testing machine can measure the anti-wear characteristics and frictional coefficient even under lubrication status. WPD-2000 Pin-disc Friction Wear Tester is available in two moods, PC & software mood or non PC mood.
-
Product
Computer Control Torsion Testing Machine
NDW Series
-
Jinan Testing Equipment IE Corporation
NDW Series computerized torsion testing machine provides loading and weighing capabilities in both rotation directions which enables it to determine conveniently not only the ultimate torque of a specimen, but also how the specimen behaves under conditions of continuous or intermittent torque loading in both directions. The computerized torsion testing machine is mainly used for the torsion test of metal and non-metal materials, as well as the torsion test for parts and components. The computerized torsion torsion testing machine is an essential instrument to measure torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
Product
Fracture Mechanics Clip-On Gages
Model 3541
-
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Ultra Fast Flexible Implantable Microprobe
IT-23
-
IT-23 Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Time constant 0.005 seconds. Tissue Implantable with a 23 gauge needle (supplied). Fairly fragile. Sensor wires are twisted TFE Teflon™ insulated. Maximum Temperature 150°C. Isolated. Probe diameter .011", 3 foot lead.
-
Product
Portable Hardness Tester
Handheld Hardness Testers
-
Handheld Hardness Testers are ideal hardness testing tools where large samples, which cannot be brought to a traditional tabletop hardness tester, or specimens with hard to access areas are to be tested. A wide variety of the portable hardness testers, offered by Qualitest ensure that we recommend the most suitable model for your application. The extensive selection of our handheld hardness testers is available from low-cost economy models up to advanced models coming with more features. These models can measure the hardness of your materials in Rockwell, Superficial Rockwell, Brinell, Vickers, Webster, Barcol scales and often conversions can be done.
-
Product
Xenon Test Chamber
-
Wewon Environmental Chambers Co, Ltd.
Xenon test chamber is affordable, full-featured, and has a large specimen capacity. It provides precise control of critical test parameters including spectrum, irradiance, relative humidity, chamber temperature and black standard temperature. Xenon test chamber is used for the selection of new materials, the improvement of existing materials or evaluating the changes in product formulation that affect product durability. This is an ideal instrument for total accelerated light stability and weathering testing.
-
Product
Evaluation Services
-
Atlas Material Testing Solutions
Atlas offers a wide range of evaluation and measurement services for our client's specimens during and after the weathering process. These services are available at Atlas' Miami, Florida and Phoenix, Arizona sites. Atlas uses the most advanced instrumentation from leading manufacturers for measuring appearance properties such as color change, gloss, distinctness-of-image, transmittance and reflectance. All of our services meet the latest measurement test standards from organizations such as ASTM, ISO, DIN and others. A full range of visual assessment services is also available, including coating adhesion, blistering, chalking, cracking, mildew growth, and gray scale evaluation in accordance with respective standards' organizations. Temperature monitoring programs are provided for single and multiple specimens under any type of exposure, as well as for large assemblies such as complete vehicles. Strict quality control guidelines have enabled Atlas' Evaluations Laboratory to achieve industry-accepted accreditation from world renowned standards' organizations. Atlas is accredited to ISO/IEC 17025 by the American Association for Laboratory Accreditation (A2LA) and accredited or approved by Ford, GM and AMECA.
-
Product
Automated XY Stage
AT2
-
The Instron AT2 is a compact automated XY stage that streamlines compression, tensile, and flexural testing for both batches of specimens and single components with multiple test points. Designed for seamless integration with 6800 Series universal testing systems, the AT2 features standard bolt patterns for custom fixturing and accommodates a wide range of specimen geometries. Fully integrated with Bluehill® Universal software, it enables operators to quickly define and execute test sequences using grid, diamond, or custom layouts—boosting throughput, consistency, and testing efficiency.
-
Product
Temperature And Humidity Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Temperature and humidity chamber is also referred to as climatic chamber, programmable temperature humidity chamber, constant environmental test chamber, constant humidity chamber, temperature and humidity controlled cabinet etc. It Is capable of simulating the range of temperature & humidity fluctuating from an extremely low value of -70℃ & 20% R.H to an exceeding high value 150℃ & 98% R.H which products may be exposed to in the natural environment. Constant temperature&humidity testing machine can be used to measure the resistance of specimens to withstanding extremely high temperature, low temperature, constant temperature, high humidity, low humidity or various programmed combinations. Applied to all materials and product which are sensitive to temperature and humidity, such as electronics, appliances, cell phones, communications, instruments, vehicles, plastics, metals, foods, chemical products, construction materials, medical products, aerospace components etc.
-
Product
Grips For Plastic Molding Materials
-
These plastic molding material grips are used when tensile testing plastics with dimensions specified in JIS K6911, plastic molding materials, and JIS K7113 No 3 specimens, as well as those shown in the diagram below.
-
Product
Data Logger for Ultra Low Temperature
DSR-ULT
-
Special probe using military industrial technology supports measuring temperature ultra low to -100 Original fittings for sensor connection, ensures 100,000 plugs Support single DSR connecting to PC via USB interface, and multiple DSR grouped in RS485 or LAN networking for central management Suitable for medical refrigerator, biological specimens preservation, scientific research and other applications
-
Product
Vacuum UV Testing Services
-
The system consists of a high-vacuum chamber, multi-ported,equipped with deuterium and xenon sources for accelerated ageing. The specimen to be irradiated is mounted on a temperature-controlled platen, which, in turn is mounted on a XYZ J manipulator. Provision is made for the measurement of emissivity and absorptance without breaking vacuum and at the operating temperature.
-
Product
Leak Tester
LT-01
-
Jinan Leading Instruments Co., Ltd.
LT-01 Leak Tester is applicable in leak testing of pouches, bottles, pipes, cans and boxes of foodstuff, pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It's also applicable in the leak testing of the specimens after falling tests and pressure resistance tests.
-
Product
Temperature shock test chambers test
TSS series
-
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
Product
Load Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
Product
Vibration Test Systems
G-9 Series
-
The G-9 Series Vibration Test Systems, featured by high eccentric moment and a large loading table supported by the unique rigid lateral suspension structure, are suited to transportation tests for relatively large specimens; packaged goods and electric apparatus. In addition, the unique structure enables horizontal tests of relatively heavy specimens without conventional horizontal slip tables.
-
Product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
-
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibrations. This unit also incorporates a new feature that allows the user to precisely set the contact force against the test specimen. This allows for even and repeatable contact force, limiting contact force induced errors. This extensometer mounts on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The gauge length for the 3549 is automatically set prior to mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
Automatic Compression Testing Machine
CTEN Series
-
Jinan Testing Equipment IE Corporation
This series compression testing machine is mainly designed for compression test of building material items, such as concrete cube, concrete blocks, cement specimen, and bricks etc, also used for compression performance test of rubber pad and top forge test of metal. With new design idea and advanced technology, this series have more advantages in appearance, operation & applications. It is the ideal test equipment for quality control at industry & mineral enterprises, education in high schools, and technology researches at scientific institutes
-
Product
Rubber Plasticity Meter
DRK209
-
Shandong Drick Instruments Co., Ltd.
DRK209 is applicable to test plasticity property when the specimen bears 49N pressure. The meter is used to test plastic value and restoration value of raw rubber, plastic rubber and rubber.
-
Product
200 N And 1 KN Roller Grips
-
This roller grip set includes both 200 N (44 lbf) and 1 kN (220 lbf) roller grips for tensile testing elastomeric ring specimens. The 200 N grips have a 4.5 mm (0.18 in) diameter roller. The diameter of the roller on the 1 kN grips is 25 mm (0.98 in).
-
Product
Test Automation Software for Laboratory Management
STARS ENTERPRISE
-
STARS ENTERPRISE is a completely new generation of software from HORIBA, consisting of innovative web and mobile apps in a cloud-based platform. It enables you to seamlessly and completely integrate all your measurement systems, test beds and specimens, as well as on-board systems in the laboratory or in mobile road tests. The numerous apps in the STARS Enterprise system offer you a universal, flexible and scalable software solution for accomplishing your entire test automation activities, today and into the future.
-
Product
Fully Automatic Plastic Tensile/Bending Testing Machine
-
This is a fully automatic tensile and bending tester for plastics. It is capable of continuous operation from measurement of specimen dimensions, supply, and data processing.
-
Product
Torsion Testers
-
For maximum torsion testing versatility and capability, Tinius Olsen offers a full range of torsion testing machines in capacities from 1,000 to 30,000 Nm. These uniquely superior torsion testers provide loading and weighing capabilities in both directions of rotation. This feature makes it possible to conveniently determine not only the ultimate torque load of a specimen, but how that specimen behaves under conditions of continuous or intermittent torque loading in both directions.
-
Product
Pendulum Impact Testers
-
Qualitest offers Charpy / Izod Impact Testers with capacities up to 750J meeting and exceeding ASTM E23, ISO, DIN, JIS, standard requirements. The key benefits of this line of top technology models are price competitiveness, extremely high precision and durability, automatic motorized lifting of the pendulum hammer to optimize cycle times, flexibility, efficiency for low/high temperature testing, and much more. Optionally we offer temperature chambers, automated sample handling, centering device, Charpy sample preparation and broaching machines for preparation of notched bar specimens.
