Face
See Also: Human Body
-
Product
Medical Solutions
-
Medical electronic products have enabled trained technicians, physicians, and biotechnologists to not only improve life expectancies, but also provide important data for ground breaking research and analysis. Manufacturers are tasked with developing the most efficient product while facing a growing number of transitions including: a push towards more sophisticated technology, the production of smaller – more compact products, changes in design ergonomics, a rise in combination products and increased regulatory rules.
-
Product
Development Tools
C251
-
The Keil 251 Development Tools are designed to solve the complex problems facing embedded software developers.
-
Product
3.0mm Preset Controls Probe
CX-A3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
Product
Save A Watt HD
P4472
-
Take control of your electronics and appliances. Simply connect them to the Save A Watt® HD timer, and they will turn on and off based on your preferred settings. Electronics which are plugged into an outlet are drawing power even when not in use, slowly draining your wallet! Having the power to program ON/OFF times saves you money, and prolongs the life of your electronics. With a large, backlit, digital face, setting the time couldn’t be easier or more intuitive. If you forget which settings you chose, it only takes a glance to find out.
-
Product
Rapid Antenna Testing Services
-
At JEM we understand the challenges facing antenna, microwave and communication system engineers, and we realize that accurate measurement of antenna electrical performance is critical. That’s why we offer a range of rapid antenna testing services from 50 MHz to 40 GHz.
-
Product
Surface Water Absorption Tester
TF167
-
TESTEX Testing Equipment Systems Ltd.
Specimens are placed at an angle on the base of the apparatus. After water flows down the surface of each specimen, the amount of water retained by each specimen is measured. Six specimens are tested, three on the face of the fabric and three on the back of the fabric. The six observations are averaged to determine the surface water absorption of the fabric.
-
Product
E-Mobility Testing
-
With the electrification of the powertrain developers face many new challenges. Electrification does not only increase the range of solutions, but also the number and type of design options. Therefore, a partner with both specific application know-how and a holistic perspective on the system is critical. We provide you with exactly this required expertise.
-
Product
Sound and Velocity Data
MIDAS SVX2
-
The MIDAS SVX2 is the standard for the offshore Oil & Gas industry. Recognising the conflict faced by users requiring the superior Sound Velocity data from an SVP, but still needing the Salinity and Density data from a CTD, the Midas SVX2 combines both technologies to give the best of both worlds
-
Product
Inductive Sensors
-
In general, inductive proximity switches consist of four basic elements: a coil, an oscillator, a threshold switch and an output stage with short-circuit protection.The oscillator generates a high frequency, electromagnetic alternating field which is emitted from the active face of the coil.Eddy currents are induced in a metal object that enters this field. These eddy currents draw energy from both the electromagnetic field and from the oscillator which is consequently attenuated.The more energy taken the closer the metal object moves towards the active face. The threshold switch switches on the output stage at a defined attenuation value.In proximity switches with a DC voltage supply, this switch is designed as an NPN transistor which switches the connected load to the negative pole or as a PNP transistor which switches the load to the positive pole. The output stage is a thyristor or a triac in AC voltage switches.
-
Product
Cabinets
-
Elma has an extensive line of configurable, modular vertical 19" rackmount cabinets and consoles, rugged and mobile racks and carts, wall- and pole-mount enclosures to effectively house and protect sensitive and critical electronics. We can meet a wide range of requirements: challenging rugged environments found in defense and aerospace applications; exposure to harsh conditions found in outdoor or factory settings; or challenging thermal requirements faced by broadcast rooms, clean labs, data and telecom centers.
-
Product
Spectrally Flat Class C Albedometer
LPPYRA06
-
Albedometers are composed of two pyranometers that are mounted back-to-back. An albedometer measures in two directions; one pyranometer is facing upwards (measuring the global solar radiation), the other pyranometer is facing downwards (measuring the reflected solar radiation).
-
Product
Temperature and Humidity Sensor, Cresnet
C2N-RTHS
-
The C2N-RTHS is a wall-mounted temperature and relative humidity sensor that communicates directly with any 2-Series control system via the Cresnet control network. One-piece mounting makes the C2N-RTHS simple to install. The 1-1/2 inch diameter face protrudes just 1/8 inch from the wall surface and is easily painted or wallpapered to blend into the wall surface.
-
Product
Melexis 90217 Hall-Effect Sensor
605-00005
-
Parallax has worked with the Melexis 90217 sensor in applications including CNC milling machine spindle speed measurement and feedback on motor RPM. With the CNC milling machine it reliably measured the top spindle speed of 7,500 RPM. This is a cost-effective and highly functional hall-effect sensor. The Melexis 90217 is designed to be used with a bias magnet (#605-00006) south facing the back (non-marked) side of the IC. With a single Hall plate, this sensor is immune to common rotary alignment problems. Very easy to interface with all microcontrollers.
-
Product
Scientific Cameras
-
Thorlabs' Scientific-Grade Cameras are specifically designed for microscopy and other demanding applications. The Zelux™ CMOS cameras have small footprints and provide cost-effective solutions for general-purpose imaging applications. Kiralux® cameras have CMOS sensors with high quantum efficiency in a compact housing and are offered in monochrome, color, NIR-enhanced, and polarization-sensitive versions. Our polarization-sensitive CMOS camera is ideal for materials inspection, flaw detection, and other advanced techniques using polarization. The Quantalux® monochrome sCMOS cameras are fast frame rate imagers that combine high dynamic range with extremely low read noise for low-light applications. They are available in either a passively cooled compact housing or a hermetically sealed TE-cooled housing. We also offer scientific CCD cameras with a variety of features, including versions optimized for operation at UV, visible, or NIR wavelengths; fast-frame-rate cameras; TE-cooled or non-cooled housings; and versions with the sensor face plate removed. An intuitive software package, API and SDK for developers, and third-party software support provide options for custom system control and image acquisition.
-
Product
Protocol Converter
MACC2
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
ACCES Wireless Data Acquisition Products
-
There have been many inquiries about our wireless I/O products. Many of these requests begin with "This is just what I need, I can't hard wire to a PC because...". Let's face it, running cable in an industrial environment can be costly, especially when you consider all the material and manpower needed to finish the job. Additionally, how can you collect data on something that is in motion like a car on a track? Our Wireless I/O products are perfect for remote installations in harsh atmospheric, industrial or marine applications. These units offer a low-cost alternative to costly signal wire installations in applications such as agricultural and irrigations systems, building management and control, security and factory automation.
-
Product
Copper Pillar Bump
-
Like in conventional fabrication, integrated circuits are created on the wafer but near the end of the manufacturing process, the attachment pads are metalized on the surface of the chips to make them more receptive to solder. Then solder dots are deposited on each of the pads, and chips are cut, flipped, and positioned so that the solder balls are facing the connectors on the external circuitry.
-
Product
Low-leakage Switch Matrix Family
-
Conducting all the parametric measurements necessary for the numerous test structures on a semiconductor wafer can be a time-consuming and expensive process. With the cost of end-user devices continuing to drop, even laboratory characterization environments must reduce the cost of test. Until now engineers and scientists working on current and future semiconductor process technologies were faced with a difficult choice: either use a semiconductor parameter analyzer with positioners on a wafer prober, which limits the ability to perform automated test, or use a switching matrix and probe card, which reduced the analyzer's measurement resolution. Utilizing a switching matrix with a semi-automatic or fully-automatic wafer prober enables characterization tests to be automated, eliminating the need to have an operator manually reposition the probes each time a new module needs to be tested. This reduces both test time and cost. Due to the many price/performance points available, Keysight's switching matrix solutions provide the flexibility to choose exactly what your testing needs require, without overspending.
-
Product
Interferometer
VFI-1200
-
The VFI is the interferometer of choice for industry leading photonics companies around the world. The VFI-1200 is an interferometric inspection system specifically designed for checking the surface quality and flatness of your cleaved or polished fibers. The VFI offers the perfect combination of a superb image quality with ease of use, and the reliability and robustness that our customers have come to expect from Arden products, resulting in fiber end face measurements that you can trust.
-
Product
Medical Masks Differential Pressure Tester
-
Sataton Instruments Technology CO., Ltd
Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.
-
Product
FlexRIO Custom Instruments And Processing
-
FlexRIO Custom Instruments and Processing products provide high-performance I/O and powerful FPGAs for applications that require more than standard instruments offer. Program these products with LabVIEW to create solutions for whatever challenge you’re facing.
-
Product
Development Tools
C166
-
The Keil 166 Development Tools are designed to solve the complex problems facing embedded software developers.
-
Product
Development Tools
C51
-
The Keil 8051 Development Tools are designed to solve the complex problems facing embedded software developers.
-
Product
Test Data Management
-
With increasing test data volumes, diverse data types, complex relationships, and data sensitivity, most enterprises face significant challenges with test data management. Having good quality data is key to testing enterprise functionality correctly and efficiently in the test environment. Copying production data to be used for the test can expose the company to numerous privacy and compliance risks. In the absence of a strong test data management strategy, you may end up jeopardizing your testing cycles and pile up huge infrastructure costs.
-
Product
Single Fiber Fusion Splicer
-
*Reversible monitor with control panel on each side*Color LCD monitor & 256 magnification*Compact & Light weight*Large capacity internal battery*Max. Wind velocity of 15m/s.*8 Sec. Splice time, 40 Sec. Tube-heat time*Simultaneous X and Y views*SYSTEM TEST ensures the best working condition*User programmable*Auto check fiber end face*Auto calibrate parameters*Store 8000 groups of splice results*Multiple language options
-
Product
Testing Solutons for Facial Masks
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
GBPI offers mask testing machines for surgical face masks, N95 masks, Melt-blown fabric. BFE Tester, PFE Tester, N95 Tester, Melt-blown fabric Tester
-
-
Product
Certified RTOS
LynxOS-178
-
The software industry is concerned with safety and is facing big challenges to make the process of certification (to any standard) more repeatable, more efficient, and more cost effective. The general software industry has been working on software re-use and modularity for many years but these concepts only touched the surface of the DO-178B industry.The LynxOS®-178 RTOS is the first and only hard real-time DO-178B level A operating system to offer the interoperability benefits of POSIX® with support for the ARINC 653 APplication EXecutive (APEX).
-
Product
Motorised and Automated Probe Heads
-
Motorised heads enable automated, repeatable re-orientation of probes to allow access to features on all faces of the part, improving the capability of the CMM and maximising productivity.
-
Product
iRobot Nodes
-
NITOS team has made mobile nodes using "iRobot Create" with a custom designed tray to hold the system board. The board is an "Alix Board" of "PC Engines" company . Commands are sent to the robot over a serial port and the whole system is powered from the robot's battery. The upward facing camera is used to recognise specific patterns on the ceiling, which help the robot navigate around the room.
