-
Product
Standard Class AAA Solar Simulator
TriSOL TSS
-
Essential for testing virtually any material or product that is exposed to sunlight for long or short periods of time, OAI’s low-cost, Standard Solar Simulators deliver highly collimated, uniform light. Depending on configuration, output on these Solar Simulators is rated at 350W -5,000W.These Class AAA Solar Simulators feature OAI’s Advanced Uniform Beam Optics and are available with a choice of air mass filters to reproduce a wide range of solar spectra. For added flexibility, OAI’s proven lens and collimating mirror technology allows for a variety of exposure area sizes. A Class AAA Solar Simulator is an essential tool for manufacturing as well as R&D; it is indispensable in test labs, industry, and in universities. OAI Standard Solar Simulators are used in photobiology, biomedical, solar cell testing, cosmetic testing, and paints & coatings analysis. Based on 35+ years of proven UV light technology, OAI Solar Simulator Systems deliver repeatable, reliable, constant output, and measurement uniformity.
-
Product
Long Life Seismic Energy Source
1900LLX-T
-
Output volume of 10 cubic inches to 250 cubic inches. Light weight enough for shallow draught vesselsPowerful enough for blue water seismic surveys. Available with engineered seals for more robust performance.
-
Product
Solar Panel Probes
-
*Effective *Reliable solution for non-destructive electrical contacting *For standard or custom applications
-
Product
Steady-state Solar Simulator For PV Modules
SORAS LS
-
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
Product
LED Solar Simulator
LumiSun-50
-
The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.
-
Product
Mid Energy Counters
-
UEM1P5-4D R for RS485 Modbus RTU/ASCII communicationUEM1P5-D M for M-Bus communicationUEM1P5-4D E for Ethernet (Modbus TCP) communicationFor 1 or 5A CTProgrammable CT ratioFully bi-directional four quadrants measurements for all energies and powersFor 3 / 4 wire networks with balanced or unbalanced load (UEM1P5-4D R and UEM1P5-4D E only for 4 wire networks)Class B according to EN 50470-3S0 output for energy pulse emissionAvailable with MID certification
-
Product
Energy Dispersive X-ray Fluorescence Spectrometer
EDX-7000/8000/8100
-
One EDX over all others The EDX-7000/8000/8100 offers a high level af accuracy and speed in analyzing elements contained in various samples.
-
Product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
-
RL78 microcontrollers greatly improve power efficiency with industry-leading low power consumption at 45.5 μA/MHz consumption during normal operation and 0.57 μA/MHz during clock operation. Built-in features such as a high-precision (±1%) high-speed on-chip oscillator, background operation data flash capable of 1 million rewrites, temperature sensor, and interface ports for multiple power supplies help reduce system costs and size.
-
Product
Solar Panel Chamber
-
Specifically designed for the solar industry, these climatic chambers feature specifically designed fixtures to properly measure almost any component related to solar panels including the actual panels, grid-tied photovoltaic inverters, or photovoltaic cells and modules.
-
Product
Long Life Serismic Energy Source
2800LLX
-
Bolt introduced the LONG-LIFE air gun in 1992. Since then it has become the standard energy source for marine seismic exploration.
-
Product
Three Phase Portable Energy Meter Test Instrument Type KP-P3003-C
-
Bofa Instrument & Equipment Co., Ltd
Three-phase portable energy meter test instrument type KP-P3003-C with current and voltage source is an ideal device to test all kind three-phase energy meters accuracy below 0.2. The equipment can generate 3-phase voltage, 3-phase current and any power factor signal, the standard meter inside the equipment is class 0.05. The equipment is box structure, light, and easy to carry, it is very convenience to test meters on site, moreover the equipment can be used for testing meter in meter manufacture and as testing equipment in R&D institute.
-
Product
*Energy Sensors For IPL Sources
-
Ophir has several ways to measure intense pulsed light IPL radiation used in cosmetic treatments. The light from these sources is broadband and usually has a high divergence. Furthermore, the light source is often coupled to the skin via an index matching gel. For these reasons, we need special solutions to accurately measure the energy of the IPL pulses.
-
Product
Green Energy Testing
-
MET is a pioneer in the testing and certification of energy efficient and alternative energy products, such as solar panels, wind generators, and inverters.
-
Product
Optical Power And Energy Meters
-
Thorlabs' expanding line of optical power and energy meters includes power meter consoles, a large selection of sensor heads, a wireless power meter with a built-in photodiode sensor, and a fiber optic power meter designed for use in the field. The consoles (PM100, PM400, and PM300 Series) when paired with our extensive line of power and energy sensors provide calibrated (NIST traceable) measurements across a broad range of powers, energies, and wavelengths. The console(s) and sensor(s) can be purchased individually or as bundles based on our most popular console and sensor pairings. The sensor calibration data is stored in the sensor head and is automatically read by the console, which allows the user to use multiple sensors with the same console. Compatible sensors are easily identified by the red c-series connector. All of our old A/B-Type sensors are available with the new connector; plus, we have continued to expand our power and energy sensor product lines.
-
Product
Solar Array Simulator
G5.SAS
-
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Product
Portable Three-Phase Energy Standard
PEWM-3C
-
The three-phase energy standard PEWM-3C is used for quick on-site tests of all types of electricity meters – for active, reactive or apparent energy, two-, three- or four-wire connection. Three voltages and three currents are measured at the same time. The current can be measured either via direct connection up to 10A (class 0.1), or with three current clamps (CC) to 120A, 150A or 1000A (class 0.2).
-
Product
Solar Reference Cell
-
The Solar Reference Cells consist of a 20 mm x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 mm x 70 mm x 16 mm metal enclosure with a protective quartz window and a temperature sensor. Designed for calibrating the irradiance of solar simulators used for testing solar cells and modules.
-
Product
Solar Simulator (JIS AAA)
PEC-L12
-
●A compact power supply box allows installation on a desktop●The irradiation direction can be freely rotated 360 degrees●A 5cm square optical filter can be attached●Quiet shutter sound (equipped with a low-noise shutter)
-
Product
Highly Collimated Solar Simulators
-
This solar simulator is based on a Fresnel lens to collimate the light beam from the arc lamp source to infinity, which results in highly collimated illumination of the target spot. A 2.5kW xenon ozone free lamp is used as the light source. The spectral distribution of the xenon light source, along with the use of specially calibrated AirMass filters, closely simulates the sun’s true spectral distribution in various conditions on Earth.
-
Product
Solar Power Meter
-
This model is very useful in the warehouses, factories, office buildings, restaurants, schools, library, hospitals, photographic, video, parking garages, museums, art galleries, stadiums, building security and so on.
-
Product
Energy Meter Calibration
GF312D1
-
Beijing GFUVE Electronics Co.,Ltd.
The instrument is a precision AC energy meter testing instrument, mainly used to test three phase energy meter error on site and measure all various of AC parameters.
-
Product
Energy Dispersive X-ray Fluorescence (ED-XRF) Spectrometer
XEPOS
-
SPECTRO Analytical Instruments GmbH
The new SPECTRO XEPOS spectrometer represents a quantum leap in energy dispersive X-ray fluorescence technology. It provides breakthrough advances in multi-elemental analysis of major, minor, and trace element concentrations. New developments in excitation and detection deliver outstanding sensitivity and detection limits yielding remarkable gains in precision and accuracy. The amazing SPECTRO XEPOS excels at critical tasks from rapid screening analysis to precise product quality control. Apply it for at-line processing in a variety of industries, for geology and mining, for environmental and waste monitoring, and for research and academia.
-
Product
Scienlab Energy Storage Discover Software
SL1091A
-
The Scienlab Energy Storage Discover (ESD) is a central component of all Scienlab energy storage test environments.The intuitive software allows users to conduct tests that deliver concrete, stable, and reproducible results.
-
Product
*Laser Power & Energy Meters
-
Ophir laser power meters work on the smart plug principle. This means that almost any Ophir power meter can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir power meters are also the most precisely calibrated units on the market thus measuring with the highest accuracy. Noted for their versatility, ease of use, and user friendly interface, Ophir meters can be used stand-alone or interfaced with LabVIEW or the user's own software.
-
Product
Energy Analyser
DUCA-LCD
-
Energy Analyser for DIN-rail mounting (4 modules), for Single-Phase/Three-Phase systems with Graphic LCD screen, Co-generation Energy measurement and "Wide Range" Power Supply (24 - 240 Vac/dc); voltage and current waveforms and harmonics measurement and visualization; 2 digital output for pulses or alarms; 2 digital pulse input. Optional RS485 serial line interface (Modbus or ASCII_DUCBUS), Ethernet Interface (Webserver / Modbus-TCP).
-
Product
Solar Array Simulator DC Module, 130V, 5A, 600W
E4362A
-
The Keysight E4362A is a 600W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4362A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
Solar Cells
-
Using high-efficiency solar panels made of silicon solar cells, the conversion rate as high as 16%, and attenuation, good reliability, long life. Frame using a high-quality anodized aluminum edge, high mechanical strength, ensuring a high level of wind resistance and anti-riot performance, can be adapted to a variety of complex and harsh climatic conditions used.
-
Product
Solar Simulator
-
Excellent reputation for its high degree of throughput, accuracy and stability. Pulsed light is used, ensuring stable measurement.Approximates the spectral distribution of AM 1.5G reference solar radiation. Achieves accurate measurement of various modules.No need to reverse modules, facilitating in-line operation.
-
Product
RL78 Family of 8/16-bit Ultra-Low Energy MCUs
RL78/L1x
-
The RL78/L1x microcontroller family is a peripheral rich family of true low power microcontrollers integrating LCD controller/driver, suitable for industrial and consumer LCD display applications. RL78/L1x offer unique display driver functionality to reduce system power consumption.
-
Product
Wireless MCU With Integrated Wi-Fi 6 And Bluetooth Low Energy 5.4
AIW-411
-
NXP RW612 Arm Cortex®-M33Integrated Wi-Fi 6 and Bluetooth® LE 5.4Rich Industrial I/O Interfaces:USB 2.0 OTG *1, PSRAM *1, Ethernet RMII *1, SDIO 3.0 *1, UART *2, SPI *1, I²C *2, PWM *3, JTAG *1, ADC *2NXP MCUXpresso SDK CompatibilityOSM Size-0 Compact Design (30 x 15 mm)
