-
Product
Ultrasonic
VEGASON
-
In non-contact ultrasonic level measurement, the sensor emits ultrasonic pulses in the direction of the medium, which then reflects them back.
-
Product
12 Pulse Diode Bridge Rectifiers Inside Fiberglass Plenums, P/N 5872C4-2
-
- 12 Pulse Diode Bridge Rectifier, P/N 5872C4-2- Each diode is rated for 60 Amps, 1800 Volts peak- Dimensions: 50″L x 40″W x 20″H approximately- Four 10″ fans are used for coolingFour 10″ fans will force cool from the bottom of the Plenum. 12 diode assemblies (each diode consists of nine diodes in series are integrated together inside the Plenum). The output is rated for 3000 VDC, 80 Amps.
-
Product
Test Data
-
Studies by major universities were conducted in response to a request from the military, scientific and engineering communities for scientific validation of claims that Pulse Technology actually improves battery efficiency and lengthens battery life. PulseTech contracted with Oakland University in Rochester, Michigan and Ohio State University in Columbus, Ohio to conduct separate evaluations of the technology. These extensive evaluations began in the summer of 1998 and concluded in the fall of 2000.
-
Product
Tunable Wavelength Systems (OPOs)
NT230 Series
-
Integrated in a single compact housing diode pumped Q-switched laser and OPO system offers hands-free, no-gap tunning from 193 to 2600 nm. Producing high up to 10 mJ energy pulses at 100 Hz pulse repetition rate, tunable over a broad spectral range, NT230 series lasers are realiable solution for many laboratory and OEM applications.
-
Product
Standard Digitizer
725S Family
-
The 725S family is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window). The wide range of DPP algorithms supported by the 725S make it a “must-have” for any type of nuclear physics application.
-
Product
High-Performance Autoranging DC Power Module, 60V, 17A, 500W
N6756A
Power Module
The Keysight N6756A is a 500 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
Semiconductor Optical Amplifier
SOA
-
Amonics SOA is a polarization maintaining optical amplifier with high fiber-to-fiber gain. It is designed for transmitter applications to increase optical launch power to compensate for the loss of other optical devices. The benchtop version incorporates a user-friendly front panel housing a LCD monitor display, key switch, power control knob and optical connectors. RS232 computer interface is also equipped on the rear panel. 1MHz with 10ns pulse width intensity modulation is available. The OEM module version is an ideal building block for OEM system integration, especially in optical communication network and CATV applications. It requires only a single +5V power supply.
-
Product
5 Digit Frequency Meter
CS2-F
-
CS2-F Freqeuncy Meter is designed high accuracy measurement, display, control and communication (Modbus RTU mode) of pulse(Frequency) or AC Frequency.● The innovation feature is auto-range input from 0.01Hz~ 100KHz(~140KHz in option). The display resolution will be auto-changed to show the highest according to input frequency. They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of testing and machinery control applications. Please refer to the detail description on pages 2/33~7/33.There are not only controllers, but also an I/O interface in any system. ADtek built in difference ideal for External Control input and Relay output as like as I/O module of PLC. It’s very connivance to achieve remote monitoring and control by CS2 series.
-
Product
Radar Simulation Software
Pulse Sequencer
-
R&S®Pulse Sequencer software together with a vector signal generator from Rohde & Schwarz or just as software provides a compelling radar signal generation solution to engineers and technicians responsible for testing radar receivers. The solution is in line with the trend of testing more in the lab rather than expensive field testing. Co-engineered with the industry, the solution supports all relevant modern radar scenario test cases and can account for real-world environments. It uses commercially available R&S®Pulse Sequencer PC software and off-the-shelf Rohde & Schwarz vector signal generators.
-
Product
High Power Fiber Laser
-
Amonics' Fiber Laser (AFL) is a compact standalone turnkey equipment to deliver up to 50W output power and 1mJ pulse energy in 1064nm and 1550nm range under CW or pulse operation. Based on proprietary all fiber design, Amonics fiber laser is maintenance free. No post-installation service is required.In pulse operation, the laser delivers up to 20kW peak power and adjustable pulse width from 10ns to 1000ns. The pulse repetition rate is triggered by external TTL signal.Amonics fiber lasers are the ideal candidate for a wide range of industrial applications.
-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
Electronic Multifunction Data Loggers
-
The DeltaTrak Electronic Data Logger is a portable, pocket sized electronic device powered by a 10-year lithium battery. It is designed for easy and reliable tracking of parameters such as temperature, relative humidity, electric current, pressure, process signals, and pulse signals. All data loggers have a built-in temperature sensor plus single or multiple external channels where different sensors can be attached for remote monitoring of a variety of parameters. The DeltaTrak Data Loggers interface with a PC and have an internal memory for up to 32,000 readings. Each data point is automatically time and date stamped as it is recorded. Sampling intervals are set by the operator via a user-friendly Windows program on the PC. Recorded data is downloaded and graphed or exported in ASCII format to a spreadsheet for numerical print outs.
-
Product
Portable Multifunctional Paperless Data Logger
S1500 Series
-
The S1500 series product is a portable paperless data logger. With 8/12/16 channel universal input and thermocouple input function, it can detect thermocouple, RTD, NTC, DC current, DC voltage, frequency, pulse count and other signals at the same time, and the collected data can be vividly displayed through various forms such as digital interface, bar graph interface, real-time curve, etc. The device has rich peripheral interfaces such as USB, TF card, RJ45, WIFI, etc. It is a portable recording instrument with rich functions, highly integrated and intelligent.
-
Product
System of High-Speed Synchronous Registration of Analog, Digital, and Video Signals
-
The system uses a high-performance NI CompactRIO controller to simultaneously register 24 analog signals, receive an accurate digital pulse from GPS and synchronize measurements.The video signal is recorded using a high-speed camera connected to an NI PCIe-1433 frame grabber. The information received from the camera and the recording device is transmitted to a server built on the basis of an industrial computer, which writes data to an external 12-disk RAID array. The stream of recorded data in the system can reach 600 MB per second.
-
Product
PCI Digital I/O
APC464
-
Four 16-bit multifunction counters/timers are configurable for pulse width modulated output, watchdog timer, event counter, frequency measurement, pulse width measurement, period measurement, or one shot pulse output. The four 16-bit counters can also be configured into two 32-bit counter/timers.
-
Product
Digitizer
720 Family
-
The 720 is a family of CAEN Waveform Digitizer able to perform basic waveform recording and run online advanced algorithms (DPP) of charge integration and pulse shape discrimination. Data is read by a Flash ADC, 12-bit resolution and 250 MS/s sampling rate, which is well suited for mid-fast signals as the ones coming from liquid or inorganic scintillators coupled to PMTs or Silicon Photomultipliers. In the waveform recording mode, algorithms of zero suppression are also implemented to reduce the data throughput.
-
Product
Pulse And Universal Generator With 25 Or 50MHz Models, Single Or Dual Channel
TGP3100 Series
-
The TGP3100 Series are true pulse generators using all digital techniques. They can replicate the capabilities of traditional pulse generators whilst adding many additional facilities such as pulse modulations.As well as operating as pulse generators, the instruments can act as high performance noise generators and as function/arbitrary generators - making them truly universal waveform generators.
-
Product
Electrical Signal Test
-
High-density, multi-channel pulse pattern generators and bit error detectors for the design, characterization and production test of optical transceivers and opto-electrical components.
-
Product
Aspirated Radiation Shield
-
The fan has an ingress protection (IP) rating of 55, virtually eliminating moisture and dust ingress. At full speed the power requirement is 1 W (80 mA at 12 V DC). To conserve power fan speed can be reduced, via pulse width modulation (PWM), to 0.3 W at night or when wind speed is greater than 3 m s-1 without loss of accuracy. If the fan is continuously operated at full speed lifetime is rated at 50,000 hours (5.7 years). The fan includes a tachometer, allowing RPM to be mounted to detect obstruction of the fan.
-
Product
Femtosecond Terawatt Ti:sapphire Laser System
MPA-XL
-
MPA-XL is a cost-effective terawatt Ti: sapphire amplifier system. It gives up to 200 mJ energy of the stretched pulse and further compression with 65% efficiency. A standard air compressor can be placed into a custom designed vacuum chamber.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 26.5 GHz
N9938A
Spectrum Analyzer
100 kHz to 26.5 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
Product
2-Channel Front End
BEQ II.1
-
*Binaural, digital equalizer with 24 bit technology and USB interface.*The digital equalizer BEQ II.1 combines the characteristics of an equalizer, a two-channel front end and an A/D converter into one mobile and very versatile measurement tool.*Binaural, aurally-accurate recordings can be conducted easily with BEQ II. The AES/EBU interface allows a quick and easy expansion into a four-channel system, e.g. with the HMS III or HMS IV. Via the ADAT interface, up to four BEQ II units can be connected, allowing for eight-channel recordings.*Integrated signal conditioning allows common measurement sensors (Microphone, Line, ICP�) to be directly connected to the front end. In addition, separate pulse inputs are available e.g. for RPM data acquisition.*Thanks to the high-performance built-in battery - external DC power supply is also possible - and its low weight, BEQ II.1 is the ideal tool for either mobile or stationary operation.
-
Product
PD Measuring System
TEM
-
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
Product
Saluki S1433 Series Handheld Signal Generator (1MHz to max. 50GHz)
-
Saluki S1433 series signal generator is a hand-held instrument specially designed for field testing. It has the functions of CW signal output, FM/AM/Pulse modulation, large dynamic range amplitude adjustment, step/list sweep etc. The integrated design of 8.4-inch large capacitive touch screen is convenient for users’ operation.
-
Product
Synchronous Generator
ZET 7190
-
The Synchronous generator ZET 7190 is intended for generating sine, pulse, saw-shaped signals. It has 2 synchronous channels and can be used individually, or as a part of control and automation systems.
-
Product
Slow Speed Switch
SS110
-
Features • Works with remote/external pulse frequency output sensor (NPN, PNP) • Setpoint ranges: 0.01-0.99 & 0.1-9.9 rpm • SPDT relay output • Monitors speeds down to 100 min. per rev • Dial-in calibration does not require power • Built-in start delay • DIN rail mounting simplifies installation • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options
-
Product
Peak Power Analyzer
4500C
-
The Boonton Model 4500C is the instrument of choice for capturing, displaying, analyzing and characterizing microwave and RF power in both the time and statistical domains. It is ideal for design, verification, and troubleshooting of pulsed and noise-like signals used in commercial and military radar, electronic warfare (EW), wireless communications (e.g., LTE, LTE-A, and 5G), and consumer electronics (WLAN), as well as education and research applications.
-
Product
CDM testers
Scorpion
-
Scorpion opens a new generation of CDM testers. It is designed to meet the new JS-002 standard and features Contact First pulse delivery. This patent pending technique of Contact CDM (CCDM) meets the latest CDM standards with higher accuracy for device classification.
-
Product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
PXIe-6612, 5 V, 8-Channel PXI Counter/Timer Module
782352-01
Counter/Timer Module
PXIe, 5 V, 8-Channel PXI Counter/Timer Module—The PXIe‑6612 performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS‑compatible digital I/O. The PXIe‑6612 can perform three simultaneous high-speed DMA transfers.
