-
-
Product
Power Distribution Modules
-
Power distribution modules (PDM) expands CAN bus control networks by replacing existing relay and fuse boxes with more reliable solid-state switches that can directly drive work lights, wiper motors, cooling fans, directional DC motors and other high current loads.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
Switched Power Distribution Module, CAN Control
H730008BS
-
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions:• Distributing the power to each device in a system• Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.The PDU has electrical monitoring of the load status in order to ease troubleshooting and maintenance tasks:• There are two light indicators per socket, to inform the user about:– Whether the plugged devices main switch is turned ON. This is helping to identify plugged devices with their main switch OFF, that therefore cannot be controlled by the PDU– Whether the power for the socket is ON. Therefore, (P ON) indicates that the PDU is giving power to the device.All the relays are CAN bus controlled.The unit has an extra power terminal block in order to extend to other units (connect more PDUs).
-
Product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
Digital I/O
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
Product
ELSFP External Laser Source
ELSFP 1000 Series
-
The ELSFP 1000 Series is a high‑power, multi‑channel external laser source designed to deliver stable continuous‑wave optical output for scalable CPO and PIC testing.It provides up to eight channels of stable CW power of up to 25 dBm per channel using the External Laser Small Form‑Factor Pluggable (ELSFP) standard to support realistic power distribution and simplify high‑channel‑count CPO and PIC test setups.
-
Product
4U 8 Slot VME64 Mini Crate
VME8008B
-
The Model VME8008B is a 8 slot VME crate, suitable for 6U x 160mm boards, with VME64 compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 50A@+5V, 10A@+12V, 10A@-12V. The VME8008 provides Automatic daisy chain and supports Chained Block Transfer (CBLT).
-
Product
Low-Voltage Arrester Analyzer
-
Weshine Electric Manufacturing Co., Ltd
1. This instrument can be widely used in equipment maintenance of substations and power plants, and to measure insulation resistance, absorption ratio and polarization index of high-voltage electrical equipment such as transformers, reactors, capacitors, and circuit breakers. The leakage current of the low-voltage arrester of the power distribution cabinet is automatically tested.
-
Product
Switched Power Distribution Module, CAN Control
H730008FS
-
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions:• Distributing the power to each device in a system• Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.The PDU has electrical monitoring of the load status in order to ease troubleshooting and maintenance tasks:• There are two light indicators per socket, to inform the user about:– Whether the plugged devices main switch is turned ON. This is helping to identify plugged devices with their main switch OFF, that therefore cannot be controlled by the PDU– Whether the power for the socket is ON. Therefore, (P ON) indicates that the PDU is giving power to the device.All the relays are CAN bus controlled.The unit has an extra power terminal block in order to extend to other units (connect more PDUs).
-
Product
Interconnect Products
-
Typical industrial applications for Oxley Interconnect products include high voltage power supplies, critical computer hard drives, fire safety control equipment, medical and pharmaceutical equipment, oil and gas control systems, power generation and distribution equipment, rail and telecommunications infrastructure. Within aerospace and military markets Oxley products are typically found in aircraft, military vehicles, ground base stations, surface ships and submarines and air and ground communications equipment.
-
Product
Tap Changer Analyzers & Winding Ohmmeters
-
Winding resistance test of inductive test objects, such as power transformers, is one of the most effective non-intrusive ways of checking its condition. Due to their advanced design, DV Power winding resistance meters provide high test currents (up to 100 A DC) and high accuracy (up to 0.1%) within light and portable test instruments. In addition to winding resistance measurement, it is also possible to perform simple, quick and reliable transformer on-load tap changer condition assessment by recording the test current during tap changer operation, also known as DVtest. Because of that, problems with a tap changer connection, contacts, and switching procedure can be detected.DV Power winding ohmmeters consist of single-phase RMO-T and three-phase TWA series. Models from the TWA series are designed for six-winding resistance measurement of power and distribution transformers, with only one single-step cable setup. As a result of reducing the total test time, it enables significant saving of time and money.Typical application areas of these instruments are high-voltage substations and industrial environments. They are intended to measure the resistance of:Transformer windingsOn-load tap changersGeneratorsElectrical motorsHigh-current bus bar jointsCable splicesWelding joints
-
Product
HAAS-1200 Accurate Array Spectroradiometer (Advanced Industry Grade)
HAAS-1200
-
Hangzhou Everfine Photo-E-Info Co., LTD
HAAS-1200 quickly and accurately measures the spectral power distribution in the range of 380nm-1000nm, and achieves the photometric, colorimetric and radiometric parameters of various luminairs and lighting sources according to the requirements of the International Commission on Lighting (CIE) standard publications.
-
Product
Wet-Mateable Connector, 10k V, 250 A
Nautilus WM10-250
-
Trends in subsea oil & gas production are moving towards deeper water and longer step out distances. These trends drive demand for higher power equipment and higher power delivery and distribution capabilities subsea with high pressures and temperatures. Teledyne ODI'™s Nautilus WM10-250 is designed with the benefit of advanced material science testing and certification, and with insulation and redundant sealing systems for reliable performance in long-term harsh environments.
-
Product
Packaged Direction Finding Systems
-
Doppler Systems offers packaged systems allowing for easy installation and use our radio direction finding systems. The packaged systems include a direction finding processor, an FM receiver, power distribution, a data interface to configure the system and obtain data from the system, and an appropriate antenna or antennas. Additionally, some customers require wireless networking to connect fixed and/or mobile sites together to share data. We also can provide laptop computers with our systems fully configured to interface with the direction finder and run our software.
-
Product
Digital Ethernet Power Meters
FU2200A
-
Beijing GFUVE Electronics Co.,Ltd.
Digital Ethernet power meter with data logger is a three-phase multifunction power and energy meter manufactured by GFUVE. It provides excellent value for monitoring power and energy management systems. It may be used as data gathering devices for intelligent power distribution or plant automation systems. All monitored data is available via a standard digital RS485 communication port, which is based on the Modbus RTU protocol.
-
Product
POWER INTERFACE BOX
-
The POWER Box is in charge to provide power supply lines towards the UUT simulating the power distribution unit. The box has been designed to host, in any mixed configuration, two kind of plug in modules:
-
Product
2U 4 Slot VME64X Mini Crate
VME8004X
-
The Model VME8004X is a 4 slot VME crate, suitable for 6U x 160mm boards, with VME64x compliant backplane. The Unit is powered by 100 – 240 Vac (50 – 60 Hz). The power distribution is 25A@+5V, 10A@+12V, 10A@-12V, 25A @3.3V. The VME8004X provides automatic daisy chain and supports CBLT data cycles.
-
Product
Spectrometer & Colorimeter
-
Spectroradiometer is widely used to measure the spectral, photometric and colorimetric parameters of all kinds of lighting sources which usually include relative spectral power distribution P(λ), chromaticity coordinate (x,y), (u,v), correlated color temperature(CCT), color rendering index(CRI), dominant wavelength, peak wavelength, spectral bandwidth, color purity, color ratio, luminous flux, Illuminance, luminance, spectral transmittance and reflectance, etc. PIMACS provides different types of spectroradiometers and colorimeter to meet the requirements in laboratories or on production lines. They are applied in the measurement for general light sources, LED & OLED products, displays, etc.
-
Product
Surge Arrester Testing
-
Weshine Electric Manufacturing Co., Ltd
This instrument can be widely used in equipment maintenance of substations and power plants, and to measure insulation resistance, absorption ratio and polarization index of high-voltage electrical equipment such as transformers, reactors, capacitors, and circuit breakers. The leakage current of the low-voltage arrester of the power distribution cabinet is automatically tested.
-
Product
Analogue (1kV below) Insulation Tester
ST-1503
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ), continuity(Ω) and AC voltage.● Instant operation is possible with a push button, convenient timer is provided with automatic power off after three to five minutes to save the battery power.● LED (red) indication when testing insulation and continuity.● Use of a high efficiency and accurate DC-DC converter.● Most suitable for insulation resistance measurement of electrical household appliances, power line distribution and installation.
-
Product
Surge Power (Joule Rating 342) (10) 5-15R 1U/0U V/H
EPSS-1015-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
12-Ch 10A RCV Power Distribution Unit
AR438
Switch Module
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
Product
LV Iron Core Shunt Reactors
-
Iron core Shunt Reactors act as an absorber of reactive power to increase energy efficiency of the power system. Shunt Reactors are used in order to compensate capacitive reactive power generated by long and lightly loaded transmission lines as well as underground cables, thus allowing the flow of more active power through the system and avoiding over voltages. Shunt Reactors can be directly connected to the power line or to a tertiary winding of a three-winding power or distribution transformer.
-
Product
1550nm High Power Fiber Optical Splitter
HPFS-1550-口口-1×N
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HPFS-1550 series high power fiber optical splitter and adopt special process of fused bi-conical taper technology and good heat treatment. It can be applied by divided high performance and high reliability to multi-port optical power distribution of 1550nm high power laser light source. The maximum pass power is 50W（47dBm）.The feature of the product is high stability, high uniformity, low polarization dependent loss and low excess loss.
-
Product
Emergency Power Supply Units (EPSU) (14) 5-20R 1U/0U V/H
EPS-1420-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
-
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
Product
Stationary Devices
-
Permanent, panel-mounted or DIN rail-installed instruments designed to monitor, measure, and analyze electrical power quality and energy consumption in power distribution systems.
-
Product
PDN Analyzer
-
The PDN Analyzer powered by CST allows you to easily resolve PDN issues as they arise in your board layout process without ever relying on a physical prototype. With digital designs continuing to increase in density and complexity, it's more difficult and critical than ever to fully understand the impact of design decisions on your Power Distribution Network (PDN) voltage and current performance.
-
Product
IMPULSE VOLTAGE GENERATOR
-
International Biological Laboratories
The impulse voltage generated in the electric power transmission and distribution system due to lightning or switching phenomena can be simulated by generation of impulse voltage of particular shape in the laboratory.
-
Product
ORing FET Control
-
Renesas' ORing MOSFET Controllers with a suitably sized N-Channel power MOSFET(s) increase power distribution efficiency and availability when replacing a power ORing diode in high-current applications. They provide gate drive voltage for the MOSFET(s) with a fully integrated charge pump.
