Elemental
of the periodic table.
-
Product
Infrared Array Sensor
Grid-EYE Evaluation Kit
-
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic Automotive & Industrial Systems has launched this evaluation kit for its Grid-Eye infrared array sensor, which integrates a ”nanopower” Bluetooth Smart module and a microcontroller. The kit is intended for prototyping the Grid-EYE sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS sensor, lens and I2C interface. The integrated Bluetooth module in the evaluation kit, the PAN1740, draws 4.9mA in transmit or receive operating modes, which means it can be powered by coin cell batteries. The IR sensor has 64 thermopile elements in an 8×8 grid format that detect absolute surface temperature without any contact.
-
Product
WDXRF Spectrometer
Axios FAST
-
Do you need non-destructive analysis of chemical composition in seconds because of time-critical process control or running sample high-throughputs? With up to 28 elements measured simultaneously in concentration ranges from ppm to 100%, the Malvern Panalytical Axios FAST simultaneous WDXRF spectrometer is the ideal solution. Accurate and robust analysis, ease of operation by less-experienced staff and high uptime go hand in hand with a low cost of ownership.
-
Product
Configuration And Visualization Software
-
Schweitzer Engineering Laboratories, Inc.
SEL software helps you optimize the configuration and management of your device and system settings. You can also use it to display and analyze relay event data, element operation, and more.
-
Product
Structures
-
Ansys offers structural analysis software solutions that enable engineers of all levels and backgrounds to solve complex structural engineering problems faster and more efficiently. With our suite of tools, engineers can perform finite element analyses (FEA), customize and automate solutions for structural mechanics challenges and analyze multiple design scenarios. By using our software early in the design cycle, businesses can save costs, reduce the number of design cycles and bring products to market faster.
-
Product
Small Spot Advanced EDXRF Spectrometer
NEX DE VS
-
Applied Rigaku Technologies, Inc
Specially designed and engineered for heavy industrial use, whether on the plant floor or in remote field environments, the superior analytical power, flexibility, and ease-of-use of the NEX DE VS adds to its broad appeal for an ever-expanding range of applications, including exploration, research, RoHS inspection, and education, as well as industrial and production monitoring applications. Whether the need is basic quality control (QC) or its more sophisticated variants — such as analytical quality control (AQC), quality assurance (QA) or statistical process control like Six Sigma — the NEX DE VS is the reliable choice for routine elemental analysis.
-
Product
Photomultiplier Tube (PMT) Bases
-
Scintillation detectors produce light as they absorb energy, and these light flashes result in the release of a proportionate number of photoelectrons at the cathode of a photomultiplier tube (PMT). Each of the ORTEC Photomultiplier Tube Bases is designed to accommodate a particular type of PMT to distribute the operating voltages to all its elements, and to derive signals from it.
-
Product
Detector & Controller
LM-Pbs TEC1
-
Lead-Sulfide Detector (Range: 1 - 2.4 micron) Detector element is 5mm x 5mm. Has a 2 stage Thermoelectric Cooler which increases the gain by 3x without an increase in noise. This is a recommended upgrade when using a monochromater with a LMC-20.
-
Product
Differential Scanning Calorimetry
Nano DSC
-
The Nano DSC differential scanning calorimeter is designed to characterize the molecular stability of dilute in-solution biomolecules. The Nano DSC obtains data using less sample than competitive designs. Solid-state thermoelectric elements are used to precisely control temperature and a built-in precision linear actuator maintains constant or controlled variable pressure in the cell. Automated, unattended continuous operation with increased sample throughput is achieved with the optional Nano DSC Autosampler.
-
Product
Gasoline and Diesel Analyzer
NAX-100S
-
Napco Precision Instruments Co
NAX-100S is the X-ray fluorescence spectrometer which is collaborative researched Sense and the University of Michigan in USA,TsingHua University in china and other spectrum experts, It is based on American high-end technology,has a design patent about the unique vacuum system ,special optics path system,designed for the detection of gasoline and diesel,has excellent stability about the ultra low content of elements analysis for petroleum chemical industry products.
-
-
Product
Single- Multielement Customized Infrared Detectors
LEPTON uncooled detector
-
Single element uncooled VPD PbSe detector, in 2 standard sizes: 1×1 mm2, 2×2 mm2, packaged in SMD or TO-5 (with cap, hermetic) with sapphire window
-
Product
Laser-induced Breakdown Spectroscopy (LIBS)
LIBS
-
HORIBA designs and manufactures for Laser-induced Breakdown Spectroscopy (LIBS) very high resolution OEM spectrometers. Thanks to a low stray light aberrations corrected concave holographic grating (Jobin Yvon Technology), HORIBA LIBS spectrometer offers in a ~90x70x30mm footprint (without electronics) a very robust and accurate spectrometer.Adopt the HORIBA LIBS spectrometer to monitor the elemental fingerprint of your liquid, solid or gas samples.
-
Product
IEC60068-2-75 Ik08 Spring Impact Hammer
CX-IK08
-
Shenzhen Chuangxin Instruments Co., Ltd.
The spring Hammer consists of three principal parts: the body, the striking element and the release system. It's used to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance with IEC/EN, UL/CSA and other international standards.
-
Product
Transducers
-
You will be able in the following page to select the tranducer that better fit your needs, by selecting the ultrasonic frequency and the diameter of the piezo element, the temperature range and the sizes of the case.
-
Product
Inductively Coupled Plasma Optical Emission Spectrometer
EXPEC-6000
-
An analytical technique used to determine how much of certain elements are in a sample.
-
Product
Configuration And Visualization Software
-
Schweitzer Engineering Laboratories, Inc.
SEL software helps you optimize the configuration and management of your device and system settings. You can also use it to display and analyze relay event data, element operation, and more.
-
Product
Primary Test Equipment
LET-4000-RDM
-
It allows to perform with sufficient power, all the primary current injections to test the proper function and wiring of all the elements that compose the protection and measuring section in a substation.
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
On-line Crossbelt Analyzers
CNA Range
-
CNA online elemental analyzers are available in three models:*CNA³: This cross belt analyzer is designed for minerals applications that feature wide conveyor belts with deep loads and large material size. It is an open analyzer that is installed below the belt with both the neutron source and the detectors below. *CNA Pentos Cement: This cross belt analyzer is used primarily in cement and related industries. It is a closed analyzer that encircles the conveyor belt with the neutron source below the belt.*CNA Nickel: This cross belt analyzer offers real-time quality control for the nickel ore mining industry.
-
Product
Arc/Spark OES Metal Analyzer
SPECTROMAXx
-
SPECTRO Analytical Instruments GmbH
The SPECTROMAXx stationary metal analyzer is used mainly for material testing in foundries and for incoming and outgoing inspections in the metal industry around the world. It determines all of the elements used in the metal industry, including metal analysis of carbon, phosphorous, sulfur and nitrogen. The seventh generation of the SPECTROMAXx arc spark OES metal analyzer comes with drastically reduced operating costs, significantly shorter measuring times and less maintenance requirements while still offering exceptional precision and stability. And when it comes to productivity, the new SPECTROMAXx sets the benchmark.
-
Product
External Temperature for PT100 Probe
TGP-4104
-
This data logger uses an external PT100 probe to record high temperatures. Probes are available to measure up to 300 and 600C. These are listed in the 'You will also need' section. The PT100 probes are of 3-wire construction and use class A elements, making them more accurate than their 2-wire predecessors.
-
Product
Tachometers
HH100
-
The HH100 Hand-Held Digital Tachometer combines both contact and non-contact sensing to accurately measure RPM, surface speed, and length. When using the non-contact mode, rotational speed (RPM) is measured using a visible beam of light. The HH100 can be up to 14 inches away from the small piece of reflective tape that is affixed to the rotating element.
-
Product
WIPL-D Pro
-
WIPL-D kernel is unique in many ways, allowing the most efficient full wave EM simulations. It is based on the Method of Moments (MoM) but applied to quadrilateral mesh elements. In addition, the basis functions are HOBFs (Higher Order Basis Functions) which means up to 2 lambdas large mesh elements. The electrical size of problems is expressed in number of unknowns, rather than in mesh elements. The quad mesh offers two times less unknowns than the traditional triangular one, while using HOBFs reduces number of unknowns several times.
-
Product
LumiCam 4000B / 2400B
-
Instrument Systems Optische Messtechnik GmbH
The latest LumiCam B generation is thus the ideal instrument for easy and reliable measurement of displays and control elements, e.g. in the automotive interior or aviation sector. It is equally suitable for tests in the laboratory and in quality assurance for small batch production.
-
Product
A to Z Testing
-
Elemental Analysis has the ability to analyze, and to test for all of the substances listed below, and many more. If you do not see the substance you need analyzed or tested for, please give us a call! We can test almost ANYTHING!
-
Product
Laser Power and Targeting
6M
-
A thin film-based single element thermopile with the largest active area in our line up at 6.0mm diameter in a large TO-8 package
-
Product
Inductive Sensors
-
In general, inductive proximity switches consist of four basic elements: a coil, an oscillator, a threshold switch and an output stage with short-circuit protection.The oscillator generates a high frequency, electromagnetic alternating field which is emitted from the active face of the coil.Eddy currents are induced in a metal object that enters this field. These eddy currents draw energy from both the electromagnetic field and from the oscillator which is consequently attenuated.The more energy taken the closer the metal object moves towards the active face. The threshold switch switches on the output stage at a defined attenuation value.In proximity switches with a DC voltage supply, this switch is designed as an NPN transistor which switches the connected load to the negative pole or as a PNP transistor which switches the load to the positive pole. The output stage is a thyristor or a triac in AC voltage switches.
-
Product
Hydrodynamic 33 kHz and 200 kHz Dual Frequency Transducer
Model TC2178
-
Model TC2178 is an optimized and hydrodynamic 33 kHz and 200 kHz dual frequency transducer ideal for navigation and hydrographic echosounder systems. The transducer has excellent piezoceramic elements which will ensure the highest reliability and quality in echosounding.
-
Product
TMR Linear Sensors
-
MultiDimension Technology Co.,Ltd.
Linear sensor utilizes a unique push-pull half bridge composed of four unshielded TMR sensor elements. The unique bridge design provides a high sensitivity signal output that is linearly proportional to a magnetic field applied parallel to the surface of the sensor package, and it provides superior temperature compensation of the output.
-
Product
Precision Pots Multiturn
-
Precision potentiometers are designed for control applications where accuracy and high-reliability is important. These devices are available in conductive plastic, wirewound or Hybritron® element types, and in various sizes. Both single-turn and multiturn models are available. Typical applications include measuring linear distance, angles or rotations in production equipment, industrial test and measurement equipment, and medical equipment.
