-
Product
1800 Watt DC Electronic Load Mainframe
N3300A
Mainframe
The Keysight N3300A is a full-rack width mainframe with 6-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3300A holds up to six N3302A, N3303A, N3304A, N3307A load modules, or three N3305A, N3306A double-wide modules, allowing a total up to 1,800 watts of maximum power.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
AC Load Banks
XL2000-XL3000 Series
-
Mosebach Manufacturing Company
The XL2000-XL3000 Series is a group of outdoor rated load banks ranging from 2000 kW to 3000 kW. These load banks range in features from permanently mounted with direct bus bar connections to trailer mounted and easy disconnect cam lock connections. Mosebach can also integrate a wide variety of control systems into the load bank to meet your needs.
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded w/ Twin Female Contacts
510150130
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
AC Load Banks
X100L Series
-
Mosebach Manufacturing Company
Introducing Mosebach’s X100L load bank. One of the lightest dual voltage, 100 kW load banks on the market! The unit weighs approximately 64 lbs. and has 5 kW resolution. The X100L load bank includes an Industrial strength, injection molded, 100% water proof case with wheels as shown below.
-
Product
Loading Transformer
CL-6
-
This readily portable Knopp Loading Transformer weighs only 60 pounds and measures 12″ long, 9″ wide, and 10″ high. Its sturdy enclosure provides protection and adequate ventilation. Two convenient carrying handles are provided. The insulating terminal panel is rigidly secured to the transformer frame, and heavy-current, bus-bar-type terminals are securely bolted to the panel. The two outpout terminals each have two connection surfaces, one on a vertical plane and one on a horizontal plane, for maximum convenience in connecting the heavy current leads and in changing, when necessary, the series-parallel links. The links and the output connections cannot interfere with each other. All terminals and connection links are plated
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
Power Load Switches
-
Low-resistance power load switches offer reliable overcurrent and thermal protection. They are designed for general-purpose power protection or for applications such as USB, hot-swap and power distribution. The power switches come in 1- or 2-channel versions with fixed and adjustable overcurrent limit. Some include a USB charge controller specifically designed to optimize USB host applications.
-
Product
Through Hole/ Donut Load Cell (3.00 O.D.) Compression Only
THD SERIES
-
Our THD Series through hole donut load cells offer an outside diameter of 3.00 inches and up to nine different through hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
48V / 250 Amp Load
BD15-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Website, Mobile & Web App Load Testing
LoadComplete
-
LoadComplete helps you design and run performance, stress, and load tests for mobile, websites, and web apps. It's very easy to use. In fact, it is so easy, that you can create your first load test within a few seconds, even without any programming knowledge. LoadComplete allows you to generate load through virtual machines, on-premise computers, or even the cloud. It's compatible with leading continuous integration environments, which allows you to find root causes immediately.
-
Product
Economical Single Point Bending Beam Load Cells
ESP SERIES
-
The ESP Series is a economical, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point bending beam design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The ESP Series features a moisture proof sealant.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Fully Loaded w/ Twin Female Contacts (p/n 610138200)
510143003
Receiver Module Insert
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Fully Loaded w/ Twin Female Contacts (p/n 610138200)
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-33S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of feeder
-
Product
Threaded Load Button
2000 Series
-
This model is a threaded load button for tension and compression load measurements up to 5000kg/ 10000lb. Fully welded cover (for SS load buttons), amplified and digitised versions are available on request. We can also customise this sensor for other thread sizes and cable sizes
-
Product
Power Transducers and Load Loggers
-
Power Transducers and Load Loggers by Ametek Power Instruments
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded with Twin Female Contacts and Round Posts (610138200 and 610138117)
510150137
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
Forced Air Cooled RF Coaxial Loads
86700 Series
-
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
Product
Time Domain Replication (Road Load Simulation)
-
The powerful graphical editor makes it easy to review and compile your field sample data for use in the test lab. The point editor, filters, velocity and displacement compensation ensure the test feasibility is evaluated at an early stage. The continuous closed-loop controller then replicates the test files with very high levels of precision. The control algorithms use a continuous coherence averaging technique to ensure a stable proactive control loop that will not only provide accurate replication but will also respond to changes in test item dynamics.
-
Product
12V 30A Battery Load Bank/Battery Discharge Tester
FST-DC12V-30A
-
Foresight Electronics Co., Ltd.
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others Discharge parameters can be monitored in real-time during the capacity test.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-80
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Big CT window*AC 1A～1800A*Current measurements of main cable
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-23S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 1A～200A*Current measurements of terminal feeder
-
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
DC Electronic Loads
-
Keysight DC electronic loads provide you with the flexibility to test a wide range of applications from power-supply test to simulation of high-intensity discharge (HID) headlamps. The 16-bit voltage, current and power-measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
Product
Single Point Aluminium Load Cell
EST-2
-
Technopark Automation & Control
The EST-2 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 400x400mm. This load cell is available in capacities from 3kg to 100kg.
-
Product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch interleaved, Fully Loaded DSO with 16 Dig Ch MSO
T3DSO2204HD-MS
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
RC-50 Artificial Phantom Load with Power Factor
480
-
The RC-50 Artificial Phantom Load with Power Factor (Catalog No. 480) has been re-designed to meet the most exacting requirements. It operates from a single phase source and will deliver current at either unity or 50% power factor at all full load ranges.
-
Product
Unclamped Inductive Load Tester
ITC55100STD
-
Model ITC55100STD performs ruggedness testing of power MOSFETs and IGBTs. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
