Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
Product
Miniature Vibration Test System
G-2 Series
-
The G-2 Series Miniature Vibration Test System, though compact & handy, consists of a sweep oscillator, sine controller, power amplifier and vibration generator, thus suited to a variety of applications; calibration of sensors, standardized vibration tests for small parts, school teaching materials and modal analysis. The G-2002 is handy, with all the composed units being incorporated in a portable case.
-
Product
GPIB-ENET/1000, Ethernet GPIB Instrument Control Device - North America 240VAC
781630-05
GPIB Controller
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
20 Slot, 3U PXI Chassis
GX7300 Series
Chassis
The GX7300 Series mainframes are 20-slot PXI chassis that can accommodate up to 19 instruments as well as a PXI controller (an embedded CPU or a PXI bus expander interface such as a MX interface). The 3U form-factor provides a compact test system foot print and provides users with the flexibility to employ both PXI and Compact PCI 3U modules.
-
Product
Boundary Scan Compliance Tester
QT900
-
Qmax Test Technologies Pvt. Ltd.
QT900 Qscan Test system is designed to provide test solution for both Boundary Scan compliance devices and Non Boundary Scan devices. The System provided with Digital IO’s capable of driving and receiving via JTAG IEEE 1149 standard interface and synchronous to JTAG pins. Both Digital and JTAG test are carried out synchronously. Use of virtual test pin and Edge connector eliminates the need of expensive test fixture strategy.
-
Product
Hydraulic Vertical Shock Test System
KRD10 series
-
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 773kΩ
50-297-043
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI Precision Resistor Module 6-Channel, 3 to 11.4M
40-297-053
Programmable Resistor Module
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
MATCO BASIC MULTIMETER
MD251
-
*Provides readings for volts, amps and ohms required for automotive electrical system tests, as well as diode and continuity tests*Beep-Jack audible warning beeps against improper a-terminal plug in and decreases the risk of damage
-
Product
Multifunction Installation Tester
COMBI519
-
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Hall Effect Measurement system
HMS-3000
-
Hall Effect Measurement System is very useful for measuring Carrier Concentration, Mobility, Resistivity and Hall Coefficient that should be pre-checked in order to grasp the electrical specifications of semiconductor device. Therefore, it is essentially required system to understand the electrical characteristics of semiconductor device.Ecopia’s HMS series consist of constant current source , terminal conversion system by Van der Pauw technique, low temperature(77K) test system and magnetic flux density input system. So, it is well-established system that has all the things needed to Hall Effect Measurement System.
-
Product
Flight Control System Test Platform
Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 6.97kΩ
40-251-124
Programmable Resistor Module
The 40-251-124 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 6.97kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Semiconductor Test Software
Test System
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Various Types of Automatic Hardness Testing System
-
Various Types of Automatic Hardness Testing System
-
Product
Thruster Test Systems
LS Series
-
The LS Series Long Stroke Thruster Test Systems are highly regarded as the industry standard for long stroke transient testing. This equipment is used in the design and production test of automotive airbag sensors by leading suppliers of automotive airbags and associative control modules.
-
Product
Modulation Distortion Up To 50 GHz
S930705B
-
S930705B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 50 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
External Frontend
FE50DTR
-
The R&S®FE50DTR external frontend can extend the frequency range up to 50 GHz for Rohde&Schwarz signal and spectrum analyzers as well as signal generators. The R&S®FE50DTR enables signal up and downconversion directly at the device under test (DUT), lowering cable losses, increasing sensitivity and delivering more power at the antenna in an OTA environment. With a dual connector system, testing of active components is an easy task.
-
Product
Photoelectrochemical Test System
SolarLab XM
-
SolarLab XM is an application specific XM (Xtreme Measurement) product that is primarily focused on solar cell / photovoltaic research, developed in conjunction with Professor Laurie Peter of the University of Bath, UK.
-
Product
AMIDA 3001XP Tester
-
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and more than doubling the number of analog channels in the entire test system. This results in a higher number of parallel tests and a higher level of capability for this system, as well as a lower and more cost-effective IC unit test cost for this tester. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The built-in instant messaging protocol detection function of AMIDA-3001XP test machine not only simplifies the complexity and difficulty of test development, but also greatly shortens the test time by using its high-speed computing capability.
-
Product
PXI based Test Systems Module
PXI XJLink2
-
The PXI XJLink2 module allows the integration of XJTAG into PXI-based test systems. PXI XJLink2 has one JTAG controller that can be connected to up to 4 JTAG chains, which are configurable for pinout and voltage. It is easily integrated with LabVIEWTM with a full set of Virtual Instruments (VIs) included.
-
Product
Multiport Coaxial Switch, DC to 20 GHz, SP4T
87204B
-
The Keysight 87204B terminated multiport switch provides the life and reliability required for automated test and measurement, signal monitoring and routing applications. Innovative design and careful process control created the Keysight 87204B which meet the requirements for highly repeatable switching elements in test instruments and switching interfaces. The Keysight 87204B is designed to operate for more than 10 million cycles. The exceptional 0.03 dB insertion loss repeatability is warranted for 5 million cycles at 25° C. This reduces sources of random errors in the measurement path and improves measurement uncertainty. Switch life is a critical consideration in production test systems, satellite and antenna monitoring systems, and test instrumentation. The longevity of this switch increases system uptime, and lowers the cost of ownership by reducing calibration cycles and switch maintenance.
-
Product
Low Frequency Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Our imaging low-frequency inspection systems are excellently suited to displaying internal defects with high resolution and high dynamics.
-
Product
Autoinjector Testing System
-
Instron’s Autoinjector Testing System is designed to perform full functionality testing on a wide variety of drug delivery devices, including safety syringes and both needle shield and button-activated formats. Developed in collaboration with pharmaceutical manufacturers and CDMOs, the system captures essential performance requirements such as activation force, injection time, dose accuracy, needle depth, and click detection. It supports compliance with international standards like ISO 11608 and can be configured for integration with collaborative robots to enhance automation and throughput.
-
Product
MCB Thermal Verification Test Bench
-
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
Product
Maxirack - 200 x 60 x 80 cm
OTP2 module no003
-
The rack serves as the basic framework for your individually designed test system. Various OTP² modules can be installed in the 200 x 60 x 80 cm rack in order to meet the most varied of test requirements.The modular architecture of the OTP (Open Test Platform) is based on a flexible instrumentation matrix, LXI-based sources and measuring devices, combined with a high-quality transfer interface for connecting the test adapters. The systems can easily be expanded with customer- and application-specific functions. We use standardization to build cost-effective systems that still fit your requirements exactly.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 1.51M
40-297-150
Programmable Resistor Module
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Quality Management Software
QMan
-
The Paperless Repair software QMAN is a powerful quality management system. It helps achieve higher quality assurance, reduce production costs and shorten repair time – regardless of which test system you are using.
-
Product
Vibration Testing System
F Series
-
Suited to durability tests for all industrial products such as aeronautical, automobile, electronic and precision equipment.
-
Product
SIP-90-3 Test System Interface Probe
SIP-90-3
ICT/FCT Probe
Overall Length (mil): 700Overall Length (mm): 17.78Rec. Mounting Hole Size (mil): 55Rec. Mounting Hole Size (mm): 1.40Recommended Drill Size: #54 or 1.40 mm
-
Product
Regenerative Battery Pack Test System
17040E
Test System
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
