-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
Vane Probe
AP472S2
-
Vane probe ∅ 60 mm with handle to measure air speed in the range 0.5…20 m/s.
-
Product
CO2 Concentration Transmitter
H5424
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Semiconductor Package Wind Tunnel
WT-100
-
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
Product
Medical Storage Chambers
KDM
-
The Bemco KDM is similar to the Bemco Koldburn KDR except it has a circular air flow conditioning system located on the chamber ceiling, and is optimized for shelf supported temperature cycling, burn-in, stress screening, and storage of valuable pharmaceutical products or medical devices.
-
Product
Radar Level Transmitter
DR6500
-
The Drexelbrook DR6500 is a two-wire open air radar level transmitter for measuring level in applications with powder and dusty atmosphere.
-
Product
Non-contact Ultrasonic Testing System
-
Yamaha Fine Technologies Co., Ltd.
Contact-free inspection through ultrasonic transmission detecting air bubbles, separation, and foreign materials inside workpieces. With a Yamaha ultrasonic amplifier installed, contact-less inspection in the air is realized. Without damaging or wetting the workpiece, it is possible to inspect the workpiece for packing defects, air bubbles, and even flaw depth.
-
Product
Combinated Sound Level Meters
-
PeakTech Prüf- und Messtechnik GmbH
Combines a sound level, lux, air humidity and a temperature measuring device. It is therefore ideally suited for professional and private use. The sound level meter enables dB measurements and the determination of sound level ratios.
-
Product
Air Data Computer (ADC) Tester
MS 1122
-
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
Product
Moisture Testers for Wood
-
Here you will find a moisture tester for wood to determine absolute moisture in different wood types. Newly-cut logs can have a moisture content of 80% or more, depending on the type. Since wood shrinks substantially when dried, it must be dried before being used in construction or most other applications. This is most often done using a large furnace called a kiln. The air drying method may also be used, but this is much slower. With the help of the moisture tester for wood you will be able to measure with high accuracy moisture in, not only raw wood, but also rolled paper products, planks, slats, beams, plywood, panels, particle board, main beams, window frames, etc., anything wooden. There are two ways of measuring moisture, these two ways are with or without damaging the material. The majority of types of moisture testers we offer at PCE do not damage the wood, or damage it very slightly.The moisture tester for wood is characterized by the measuring principle and the moisture sensors that can be adapted to it. The moisture tester for wood has special characteristics such as an automatic compensation of temperature. Besides, data can be stored and transferred to a PC or laptop, or characteristic curves can be programmed for specific wood types (only with the model FMD). Our moisture tester are of the highest quality standards in the industry, and are durable and easy to use.
-
Product
CO2 Concentration Transmitter
H5024
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature and relative humidity are recomputed to following humidity expression: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Temperature, Humidity, CO2 Transmitter
H6020
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Chemiluminescence Method Ozone Analyzer
AQMS-350
-
The AQMS-350 is used to detect and evaluate the O3 concentration level of one of the environmental air quality parameters (SO2, NO2, CO, O3, PM2.5, and PM10) based on chemiluminescence technology. This analyzer can measure the concentration of O3 in ppb~ppm level, with strong anti-interference capability, high repeatability, and accuracy.
-
Product
OM Thermal Stress System
-
Conductor Analysis Technologies, Inc
The OM Thermal Stress System is a cost-effective performance based reliability test methodology which performs convection reflow assembly simulation and air-to-air thermal cycling. The methodology is utilized by both the IPC PCQR and the IPC 6012-QLM programs. OM systems are available for sale or lease, and test services are provided from both CAT and our service partners.
-
Product
Compact Air Quality Monitoring System(SO2, NOx, CO, O3, PM10, PM2.5, VOC)
AQMS-1000M
-
The Compact system is the alternative solution against standard AQMS, it comes with integrated shelter consisting IPC, sampler, AC and all necessary accessories.
-
Product
Electrostatic Discharge Test
-
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
Product
Oxygen Compound Instruments
-
Teledyne Advanced Pollution Instrumentation
Teledyne API’s range of instruments for Oxygen compounds utilize advanced technology to produce some of the most accurate measurements available.All T Series instruments offer two front-panel USB ports, an advanced touch screen full color display, customizable user interface with predictive maintenance alerts, one-touch real-time graphing, and multiple language support. All of our instruments are designed meet the rigorous demands of ambient air quality, stack, or industrial process gas monitoring.
-
Product
NITOS Wireless Sensor Platform
-
The NITOS prototype wireless sensor mote, is comprised of open-source and configurable modules. NITOS mote features the ATmega32u4 microcontroller running at 8MHz and operating at 3.3V. The aforementioned microcontroller is fully compatible with the Arduino platform that enables ease of software development and provides compatibility with several commercial sensing modules. Moreover, the platform is equipped with an Xbee radio interface that enables communication with the respective gateway. The Xbee module is a tiny device ideal for setting up mesh networks and has a defined rate of 250 kbps. This module uses the IEEE 802.15.4 stack which is the basis for theZigbee protocol. Apart from the Xbee module, NITOS mote can also feature a WiFi wireless interface in order to communicate with WiFi gateways. The developed mote currently features specific sensing modules, an air temperature and humidity sensor, a light intensity sensor and a human presencesensor. Various types of sensing modules and actuators can be further integrated exploiting existing Arduino software that implements several existing communications protocols. The firmware can be easily uploaded through the on-board USB connection. Figure 1 illustrates the developed NITOS mote and the respective gateway node.
-
Product
Brake Testers
-
Orbit Controls Decelerometers are mobile measuring devices for measuring the braking behavior of road or rail vehicles as well as trailers depending on the braking force and pressure in the air or hydraulic braking system.
-
Product
Transceiver Interfaces
TI
-
Analog audio interface is a connection to transceiver audio output (external speaker connector or line output) and transceiver audio input (microphone connector or line input). Audio interface enables operating digital modes, recording and playing voice, as well as other useful functions (such as measuring levels of a signal from the air) by using a computer.
-
Product
Zero Field Cavity
-
Zero field cavities generate a zero magnetic field in an air gap. They are mainly used to calibrate hall probes for their zero scale value of output for the magnetic field strength H or the magnetic flux density B they measure. For example Gaussmeters can be calibrated by using Zero Field Cavity.
-
Product
Thermometer Hygrometer Barometer
H7531-2
-
Sensor H7531 is designed for online monitoring of temperature, relative humidity of air without aggressive substances. Three binary inputs to detection of two-states signals are the advantage. Other devices are controlled by two relay outputs.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Precision High Current Resistors/Shunts
-
Measurements International Ltd.
The precision high current shunts are a series of High Current Resistors ranging from 1 A to 3000 A with optional air moving fans and resistance values from ohms to micro-ohm.
-
Product
Handheld Humidity/Temp Hygrometer
625
-
The Model 625 is an ideal instrument for indoor air quality (IAQ) and indoor environmental quality (IEQ) measurements of temperature and humidity. The EdgeTech 625 temp/RH probe can be used two ways: use it as an integrated unit by attaching the probe head to the instrument or connect both parts via a cable. The clear back-lit display can be switched between relative humidity, wet bulb, and dew point at the touch of a button.
-
Product
HVAC Drives
-
Our variable frequency drives are designed for HVAC applications, which include air handlers, cooling towers, and pumps, by combining reduced size and cost with advances in performance and quality.
-
Product
Measuring Instruments
-
Since acquiring the Kimo and E Instruments brands, we have added a comprehensive range of measurement instruments to the Sauermann product portfolio. These instruments are designed to monitor indoor air quality (IAQ) and combustion gas machines during installation and maintenance operations by measuring concentrations of gases and other substances in the air.
-
Product
Temperature, Humidity, CO2 Transmitter
T6440
-
The transmitters are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Medical Grade All-in-One Panel Computer with 13.3”/15.6” Full HD Display
MLC-AL/ MLC-KL
Panel PC
The MLC-AL/MLC-KL Series of medical panel computers feature a fully sealed aluminum housing for easy cleaning. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the MLC-AL/MLC-KL Series can be easily and quickly cleaned using all common disinfectants and cleaning agents.The MLC-AL/MLC-KL comes in two display sizes, 13.3” and 15.6”, which are ideal for ICUs, emergency rooms and the hospital wards. In addition to the standard galvanically isolated network connections, the MLC-AL/MLC-KL can be optionally equipped with galvanically isolated USB and serial interfaces for connection to external non-medical devices. Compliant with 2x MOPP, the MLC-AL/MLC-KL meets the comprehensive requirements of the IEC/EN-60601-1 (Edition 3.1) and IEC/EN-60601-1-2 (4th Edition) standards.
-
Product
Enlarge Environmental Chamber
REXMED REC-480
-
MOD. REC-480, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 2.3KW X 2pcs, Humidity heater: 4.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 5,270 Watts, 18,000 BTU/hr, 4,545 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L100 X W80 X H100cm, Capacity: 800L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Oil Tan Delta Tester
OTD
-
The Oil Tan Delta (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. Megger has developed features of the OTD to ensure that productivity levels within laboratories are maximised. The microprocessor controlled inductive heater means that there is uniformity of temperature throughout the cell, in compliance with IEC 60247, and for cooling a fan effectively speeds up the cell cooling time. The instrument has a temperature measuring range of 10 to 110 C, with an accuracy of 1 C. It can be set to preheat before testing takes place. The automated oil drain facility negates the need to move the oil vessel. User safety is paramount and with this in mind, Megger have designed independent and dual redundant high voltage cut-off circuitry. If for any reason the user needs to abort the test, this can be done so by pressing any key, immediately terminating the test and removing the high voltage. The design of the cell components maximise oil fill rate but minimise turbulence in oil flow and eliminate trapping of air. With only 32 cell components, it is easy to assemble and disassemble.
