PXI Express
Bi-directiona data throughput up to 6 GBytes per sec and electro-mechano interoperability with CompactPCI Express.
See Also: PXIe, CompactPCI Express
-
Product
PXI 8 Slot BRIC 138x8 1-Pole (3 sub-cards)
40-560A-121-138X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8-Slot BRIC Matrix, 40x32 1-Pole (8 sub-cards)
40-562B-121-40X32
Matrix Switch Module
The 40-562B-121-40X32 is a high density BRIC8 matrix module with a size of 40x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Multiplexer Single 48 Ch 1 Pole
40-632-021-48/1
Multiplexer Module
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
Fault Insertion Unit
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
PXI 50 x DPST Electromechanical Relays
40-146-202
Relay
The 40-145/46/48 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose relays are suitable for the construction of small switching networks, I/O port switching, for slave switching larger relays or for operating external devices (e.g. lamps, solenoids etc.).
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-132-HI
Programmable Resistor Module
The 40-230-132-HI (PXI) and 42-230-132-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 26.7kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
6-Port PCI Express
PEX 8724
-
The ExpressLane™ PEX 8724 is a 24-lane, 6-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8724 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-356-HI
Programmable Resistor Module
The 40-230-356-HI (PXI) and 42-230-356-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 76.8MΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 32x6 Matrix Module, 1-pole 2A 60W
40-506-001
Matrix Switch Module
The 40-505/506/507/508/509 are a range of medium density matrix modules able to switch up to 2 Amps or 300VDC/250VAC. They are constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 2 Amp Multiplexer, Dual 16-Channel, 1-Pole
40-635A-105
Multiplexer Module
The 40-635A-105 is a dual 16-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI 32 Chan I/O Parallel I/P Prog Threshold
40-412-111
Digital I/O Module
A 32-channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. Each of the 32 channel outputs can be used to drive the output high or low usinga high current capacity drive capable of sourcing 0.4A from the high side or 0.5Asink on the low side for each channel. The module is available in two versions witheither serial or parallel capture of the input levels.
-
Product
PXI 8 Slot BRIC 275x4 2A 2-Pole Matrix
40-566A-105
Matrix Switch Module
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI Fault Insertion Insertion Switch Modules
-
Our PXI Fault Insertion Insertion Switch Modules feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect – all of which can simulate connectivity problems in the system.
-
Product
PXI 8x2 RF Matrix 1.5GHz 50 SMB
40-750-511
Matrix Switch Module
The 40-750-511 is an 8x2 RF Matrix Module suitable for switching frequencies up to 1000MHz. It has a 50Ω characteristic impedance with front panel mounted SMB coaxial connectors. The matrix intended for the easy construction of high performance bidirectional switching systems.
-
Product
PXI 8 Slot BRIC 77x16 1-Pole (7 sub-cards)
40-562A-121-77X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI Potential Divider Module 24-Channel (no resistors fitted)
40-282-121
Programmable Resistor Module
The 40-282 is a potential divider with up 24 separate channels. This can be used to emulate potentiometer devices, each channel having a fixed R1 R2 ratio. Additionally, the centre point can be shorted to either of the potentiometer end points.
-
Product
PXI 8 Slot BRIC 264x8 2-pole (12 sub-cards)
40-562A-122-264X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI High Density Multiplexer, 10-Bank, 8-Channel, 1-Pole
40-615A-014
Multiplexer Module
The 40-615A-014 is a 10-bank, 8-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI Single 46x4 Matrix, 1 Pole Switching
40-524-021
Matrix Switch Module
Medium density PXI dual 46x4, 1-pole matrix - it is also available inreed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Product
Tunable Laser Source - PXI
Laser 1000 Series
Laser Source
The Laser 1000 Series PXIe module is a Continuous Wave (CW), tunable laser source offering high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
Product
PXI Multiplexer Dual 32 Ch 1 Pole
40-630-022-D/32/1
Multiplexer Module
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1.5Ω to 1.81kΩ
40-251-022
Programmable Resistor Module
The 40-251-022 is a programmable resistor module with 4 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-254-HI
Programmable Resistor Module
The 40-230-254-HI (PXI) and 42-230-254-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 22.05MΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 12-Slot BRIC Matrix, 35x32 1-Pole (7 sub-cards)
40-562B-321-35X32
Matrix Switch Module
The 40-562B-321-35X32 is a high density BRIC12 matrix module with a size of 35x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 30x32 1-Pole (6 sub-cards)
40-562B-321-30X32
Matrix Switch Module
The 40-562B-321-30X32 is a high density BRIC12 matrix module with a size of 30x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
FPGA PXI Digital I/O Card
GX3500
-
The GX3500 is a user configurable 3U FPGA PXI card which offers 160 digital I/O signals for specific application needs. The card employs the Altera Cyclone III FPGA which can support clock rates up to 150 MHz and features over 55,000 logic elements and 2.34 Mb of memory. The 3U PXI FPGA card GX3500 can also accept an expansion card assembly which can be used to customize the interface to the UUT – eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system.
-
Product
PCI Express Mini Module
-
PCI Express Mini Module provides a simple and standardized way to add I/O and storage functions to embedded board without increasing the overall size.
-
Product
PXI Power Relay Module, 10xSPST, 16 A, With Interlock
40-161A-003-HI
Relay
The 40/42-161A-003-HI is a PXI/PXIe 10xSPST power relay modulewith optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI Power Relay Module, 12xSPDT, 16 A, With Interlock
40-161A-101-HI
Relay
The 40/42-161A-101-HI is a PXI/PXIe 12xSPDT power relay module with optional hardware interlock. It is part of a range of high density power switching solutions with a choice of SPST, and SPDT relay configurations with or without hardware interlock.
-
Product
PXI Single 8 Channel Optic Mux FC/APC
40-852-018
Fiber Optic Switch
The 40-852-018 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
