Noise Monitors
-
Product
Noise Consultants Assessment System With 1/1 & 1/3 Octaves Class 1
01NK111/112
-
This Noise Assessment System can be configured to your exact requirements, making it the ideal product for Noise Consultants who perform a wide variety of noise assessments for industrial and environmental noise.
-
Product
Ground Fault Monitors
IFT
-
In most industrial settings, ground faults can cause significant damage. Since these leaks are unavoidable in almost all industrial environments, our ground fault monitors allow you to quickly and easily find the source of the leak before a major problem occurs and damages your equipment. The IFT-120 is designed to help you rapidly locate ground faults.
-
Product
Collapsible 6 Inch Charge Plate Monitor Assembly
CPM-760A
-
- 6" x 6" (15 cm x 15 cm) conductive plate- Total system capacitance of 20 pF ± 2 pF- Meets the requirements of ANSI/ESD STM3.1 and ANSI/ESD SP3.3- Designed to perform audits on overhead ionizers and room ionization systems- Flexible to also evaluate and balance bench top ionizers- Completely collapsible for compact storage- Designed to be used with the PFM-711A and PFM-711B
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Intelligent Application and Service monitoring
Datadog
-
With turn-key integrations, Datadog seamlessly aggregates metrics and events across the full devops stack.*SaaS and Cloud providers*Automation tools*Monitoring and instrumentation*Source control and bug tracking*Databases and common server components*All listed integrations are supported by Datadog
-
Product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
-
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
Product
Monitoring System
TriGas X5000
-
The TriGas X5000 Monitoring System is an integrated gas detection solution that helps plant operators comply with NFPA 820. The system monitors for combustible gases, hydrogen sulfide and oxygen with on-board alarming and communication interface to plant and remote location control stations.
-
Product
Mobile Network Monitoring
NetMobility®
-
The next generation of mobile network monitoring is here. With NIKSUN NetMobility® you gain unparalleled insights into subscriber behavior, carrier services, network health, cyber threats, and application performance to meet a wide range of service provider needs - Performance, Security, Operations, Management, and Planning.
-
Product
Gamma Air Monitor
Quant Air
-
QuantAir is a solution for measuring radioactive contamination in the air, it provides high-performance detection capabilities with accurate in-field quantification.
-
Product
Condition Monitoring
Bearing Defender
-
The patented, wireless Bearing Defender provides instantaneous feedback on bearing health. It is user-friendly, can be used on just about any industrial machine, and detects bearing faults quickly and accurately.
-
Product
Spectrum Monitoring and Interference Systems
-
Automate wide area, close-proximity signal monitoring, interference detection, identification, location, reportingIncrease flexibility; set up rugged, portable-RF sensors in fixed, temporary or mobile platforms in any environment for extended periods of timeRemotely deploy a single sensor or a network of sensors synchronously country or city-wide, or in a roomCustomize for your application with software for spectrum monitoring, emitter location, signal intercept, capture/analysis
-
Product
SNS Series Noise Source 10 MHz to 26.5 GHz (ENR 15 dB)
N4002A
-
The SNS series N4002A noise source was designed to measure DUT noise figures reliably and accurately up to 30 dB from 10 MHz to 26.5 GHz.
-
Product
VoIP Infrastructure Monitoring and Maintenance
NetVoice®
-
NIKSUN NetVoice® is the essential tool to monitor and maintain optimal network operation of your VoIP infrastructure. The NIKSUN solution monitors the network and alerts the administrator when abnormal network behavior or deterioration occurs, providing essential management and trending reports (periodic or on-demand) to plan for future network needs.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
15T Standard Running Line Monitor
RLM15T-3.0-S
-
The DLM 15T Running Line Monitor measures the tension on a rope passing through its three wheels. Typically used in cable laying and winch operations to measure and record line tension the robust design has become an industry standard. The monitor can be supplied as a separate item for integration with customers existing PLC’s or with a DLM digital display/HMI touch screen display.
-
Product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
-
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
Product
C/Ku Band Satellite Monitoring
SCL-3412
-
C/Ku Satellite Monitoring System (SCL-3412) is designed to intercept International/national telecom carriers, GSM A/Abis links and IP Carriers over satellite which are using C, Ku, X or Ka-Band. In order to reduce the manual effort and time consumed in the analysis of the carriers, system is integrated with Satellite Carrier Analysis module, which automatically performs the scanning on the selected spectrum and provide the list of carriers along with their payload type (i.e DCME, GSM or IP) and characteristics parameters. This provides great help to take decision for monitoring of the carriers of interest.
-
Product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
-
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
Product
Noise Figure Measurements With Vector Correction
S93029B
-
The S93029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers, utilizing Keysight’s unique vector-source-correction technique
-
Product
Crimp Force Monitor
638007950
-
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
Product
Biogas Monitoring
-
Get more value out of waste by increasing revenue and keeping operating costs in control. The world's first Ex certified optical in-line instrument family the Vaisala MGP260 series is here.
-
Product
Engine Health And Vibration Monitoring
-
Engine Health and Vibration Monitoring systems provide the data required to support condition-based maintenance and “power-by- the-hour” commercial frameworks. They can also tell the pilot or maintenance crew if the engine rotors are out of balance (a mandatory requirement for passenger-carrying jet-powered civil aircraft).
-
Product
Continuous Emissions Monitoring
atmosFIR CEM
-
atmosFIR CEM is a complete emissions monitoring system incorporating the atmosFIR 19” FTIR analyser. As completely hot and wet emissions measurement, atmosFIR CEM is ideal for complete measurement of multiple gases from applications such as incineration and power. A standard gas suite of NO, NO2, N2O, SO2, NH3, HCl, CH4, O2, CO2 and H2O is provided, but with the powerful FTIR analyser, further gases can be added easily in software.
-
Product
Predictive Vibration Monitor Solutions
VMU
-
Vibration Monitor Units (VMUs) from Astronics employ proven vibration analysis to predict the failure of fans and other rotating equipment on passenger and cargo aircraft. Accurate prediction allows maintenance to intervene before a failure can occur, eliminating the resulting smoke or smoke smell event that can result in costly flight delays, diversions, emergency landings, or cancellations.
-
Product
PXI Monitored Multiplexer, Dual 64-Channel, 1-Pole
40-619-302
Multiplexer Module
The 40-619-302 is a high density PXI 2 A multiplexer module in dual 64-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC - Single
-
Product
CMAS Analyzers and Field Monitors
-
Backed by at least one of the 8 corrosion sensor patents wholly owned by Corr Instruments, our nanoCorr analyzers and field monitors are widely used for online and real-time localized and general corrosion monitoring. These ultra-high precision instruments measure extremely low currents in the pico-ampere levels, which can be translated into a corrosion rate as low as a few nanometers per year, in some applications (PDF). Our analyzers and monitors are based on the patented coupled multielectrode array sensor (CMAS) technology which measures the flow of electrons from corroding electrodes to one or more cathodes.
-
Product
Mini Fiber Optical Monitoring Alarm System
Mini FOMA
-
Mini FOMA (Fiber Optical Monitoring Alarm System) is integrated RTU (Remote Test Unit) 、Center Monitoring Server and its management software to achieve integrated operation、remote management、unattended monitor、periodic fiber scan、predictive analysis and support the instant fiber with status information and alarm warning, accurate of long-term fiber data record.
-
Product
Cleanroom Monitoring System
CRMS
-
The Kanomax Cleanroom Monitoring System offers turnkey solutions for monitoring needs required by various industries such as pharmaceutical, medical device, aerospace, semiconductor, and automotive.
-
Product
Remote Display Gas Monitor
Chillgard® 5000 Remote Display
-
The Chillgard® 5000 Remote Display provides gas monitor information before room entry where potentially hazardous gas levels may exist. It mimics the Chillgard 5000 Gas Monitor readings for gas concentration, alarm status, calibration.
-
Product
Ultra Low Noise Preamp
J2180A
-
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
