Noise Monitors
-
Product
Organic Pollutant Monitor
OPSA-150
-
The OPSA-150 is a organic pollutant monitor that uses HORIBA's proprietary Rotary Cell Length Modulation, a measuring technique incorporating 25 years of expertise. The unit can be used as an organic pollutant monitor at drainage systems for determining compliance with COD monitoring regulations, for monitoring quality of water measuring levels of organic matter at water supply intakes, and as an organic monitor on process lines (phenol meter).*Pole mount, outdoor cover, and analysis panel are available as options.
-
Product
Full Bandwidth Monitoring
Bluehorn System
-
When reproducing complex sounds, pattern relationships matter just as much as amplitude and frequency. Perfectly linear acoustical output requires phase re-alignment of the input signal. But thanks to the laws of physics, even the most accurate acoustic systems have introduced phase anomalies—until now.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
Phase Noise Generator / Calibrator
PNG-A
-
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
Product
Low Noise Pre-Amplifiers
-
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
Product
Flow Monitor
B2900
-
Blancett B2900 flow monitor offers advanced digital signal processing technology in an easy-to-access package. Enclosed in a spacious polycarbonate NEMA 4X housing, the electronics are located on a single board, designed for straightforward and convenient field installation. The B2900 enclosure features an LCD display with push button programming as well as a pre-drilled hole for external wiring connections, such as Modbus RTU and other outputs.
-
Product
RF Sensor for Spectrum Monitoring
N6841A
-
Reduce operating costs with affordable spectrum monitoring and TDOA geolocation measurementsDeploy fully capable RF monitoring stations faster with simple hardware and measurement-specific software24/7 real-time remote spectrum monitoring with Signal Surveyor 4D softwareCapture intermittent signals with spectrum analysis softwareFaster search and signal isolation with broad attenuation and wide dynamic rangeLocate narrow or wideband signals with geolocation software
-
Product
Single Phase Powerline Monitors
-
a Voltage disturbance detector and recorder. This device is designed to be plugged into a 120V or 240V AC line and will monitor this line for voltage disturbances and temperature or Humidity variations.
-
Product
Explosion Proof Area Hydrogen Monitor
HY-ALERTA™ 2620
-
H2scan’s 2620 Explosion Proof Area Hydrogen Monitor provides hydrogen-specific leak detection and measurement for hydrogen concentrations as low as 4000 ppm and can be scaled to any concentration up to 5% hydrogen by volume, a range representing 10% to 125% of hydrogen’s low flammability limit. The monitor is designed for either ceiling or wall mount. H2scan’s hydrogen-specific sensor technology has no cross sensitivity to other combustible gases, thus eliminating false positive alarms and ensuring safety system reliability.
-
Product
Tick-to-Trade Data Monitoring Appliance
NetTradeWatch™
-
NIKSUN NetTradeWatch™ is a tick-to-trade data monitoring appliance that is specifically software engineered to address the needs of highly dynamic and complex trading environments. NIKSUN NetTradeWatch™ combines the critical capabilities of multicast data monitoring, determination of data quality, and deep analytics related to transactions for 100% visibility into the financial network environments, making it the solution of the choice in a specialized market.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 7 GHz
N8974B
-
The N8974B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8974B.
-
Product
Ultra Low Noise DC Power Supplies
R4G Series
-
R4G series are series regulator system DC power supplies so that enabled setting and reading out more fine output with a 4-digit indicator on furont panel and a high resolution D/A and A/D converter adopted newly.
-
Product
Control, Monitor, Security and Power Management for ATEs
-
Subset of 6TL's FastATE modules designed for the control, monitoring, security, and power management of ATEs (automated test equipment).
-
Product
PXI Test System Dev, Debug & Monitor Software
InstrumentStudio
Test System
InstrumentStudio is free application software that provides an integrated approach to interactive PXI measurements. InstrumentStudio helps you to unify your display, export instrument configurations to code, and monitor and debug your automated test system. You can view data on unified displays with large, high-resolution monitors, and then capture multi-instrument screenshots and measurement results.
-
Product
Helicopter Reducer Vibration Monitor
-
The complex is built on the basis of the measuring platform NI PXI and provides measurement and calculation of vibration parameters. The software of the complex is two-level: the lower hardware level and the upper level of the user interface. The hardware level software provides the following functions:interrogation of measuring modules;signal processing in the time domain;calculation of measuring parameters;spectral analysis;recording the signal to the hard disk.
-
Product
Low Noise Amplifiers
-
LNA amplifier PE15A1000 is rated at 13 Volts DC maximum and 200 mA. Our low noise radio frequency LNA amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial millimeter wave low noise amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
Low Concentration Monitor- Sulfuric Acid/Hydrogen Peroxide
HF-700A
-
The HF-700A stabilizes hydrofluoric concentrations on the order of ppm in diluted sulfuric acid and hydrogen peroxide to enable continuous measurement and allow effective process management of the removal of the polymer residue following the etching process.
-
-
Product
Condition Monitoring
Falcon
-
The ultimate portable vibration data collector and analyzer. With a wide range of optional features available, the FALCON can be configured to perform balancing, run up coast down, frequency analysis and more.
-
Product
Air Gap Monitoring & Analysis
-
Solutions for air gap monitoring in order to plan maintenance prior to reduced operating efficiency or damage from magnetically induced heating or rubbing between the rotor and stator.
-
Product
CO2 And H2O Monitor
EGA30
-
A highly stable monitoring system that measures CO2 to 1ppm in a range of 0-2000ppm, and H20 to 1% relative humidity in a range of 0-100% relative humidity. The instrument is designed for long-term monitoring.
-
Product
Optical Channel Monitor
-
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
Product
Ultra HD Surgical Monitor Series
ASM32U
Industrial Monitor
The ASM32U Series of medically certified UHD surgical monitors features clear image and accurate color reproduction to fully support medical personnel. As a result of its hygienic surface design that eliminates exposed screw heads and air vents, the ASM Series can be easily and quickly cleaned using all common disinfectants and cleaning agents. This ensures a high level of hygiene in pathogen-sensitive environments such as the OR. The ASM Series’ hygienic design also can speed up turnaround time and operating theater preparation.
-
Product
H2O2 Monitor
HZ-960HPO-M
-
High stability measurement H2O2 concentration. The repeatability: FS +/- 0.2%. Can select 4 types of measurement range in-line detectors.
-
Product
Two Way Monitoring and Control
-
The Drexelbrook 560 DRX Series wireless products feature 900KHz frequency hopping, spread spectrum technology to provide a reliable, license free, wireless link between the field instrument and the control room.These wireless interface products provide a cost effective alternative to expensive hard wired connections.Using Frequency Hopping Spread Spectrum (FHSS) technology, a robust signal is provided that is virtually free from disruption due to interference.
-
Product
System Controllers & Battery Monitors
-
UNIPOWER System Controllers & Battery Monitors provide battery management functionality for the Aspiro, Guardian and Sageon DC Power Systems. The proprietary PowCom software enbles the user to monitor multiple Aspiro or Guardian systems at different locations using a highly intuitive GUI. SageView software provides similar fucntionality for Sageon systems and also works with the standalone Sageon Shield battery monitor.
-
Product
SAFE-T-GROUND - Ground Continuity Monitor / Control
TR-7
-
Model TR-7 Safe-T-Ground provides continuous monitoring of a truck's ground connection throughout loading operations. Static electricity is often brought in by tank trucks entering the loading area. The Safe-T-Ground Model TR-7 instantly stops loading operations if a tank truck loses its ground.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC 0.1A～500A*Current measurements of feeder
-
Product
In-Situ Spectroscopic Ellipsometer for Real-Time Thin Film Monitoring
UVISEL Plus In-Situ
-
The UVISEL Plus in-situ spectroscopic ellipsometer can be easily mounted on process chambers (PECVD, MOCVD, sputter, evaporation, ALD, MBE) for the real-time control of thin film deposition or etch processes.The UVISEL Plus in-situ provides the unique combinations of very high speed, sensitivity, dynamic range and accuracy making the instrument able to control deposition / etch at the atomic layer thickness level, even for rapid processes.
-
Product
Air Quality Monitoring System
-
A system that measures metrological parameters such as wind speed, wind direction, rainfall, radiation, temperature, barometric pressure and ambient parameters.
