Filter Results By:
Products
Applications
Manufacturers
Model
construction of a concept.
See Also: Modeling, Modelling, Modelers, Human Body Model, Charged Device Model
-
product
AMR Module Warm-up Station
3206G
The Model 3206G Meter Warm-Up Station for AMR Modules has been specifically designed for meters that utilize the DCSI TWACS™ power line carrier communications module. Additionally, this versatile unit includes voltage output and voltage input connections that allow you to test additional brands of power line carrier modules when using the manufacturer’s supplied module. The Model 3206G can even be used as a simple meter warm-up station.
-
product
Step Attenuator
RSC
The R&S®RSC is a switchable, mechanical step attenuator. It is available in various models with up to 6 GHz and 18 GHz, and can also control compact external units up to 40 GHz and 67 GHz. The base units provide a GUI for various settings, calibration and configuration of external modules. All models have RF connectors on the front panel or rear panel for rack installation
-
product
Paramagnetic Oxygen Analyzer
Model T802
The Model T802 O2 uses the proven paramagnetic measurement principle, coupled with state of the art microprocessor technology, to provide accurate and dependable measurements of Percent-Level O2.Paramagnetic technology is non-depleting, which means that there are no consumable parts, and ensures a consistent performance over time. The selectivity of the paramagnetic measurement for oxygen means that there is little or no interference from other common background gases. The T802 offers a stable and inherently linear measurement of oxygen, making it possible to calibrate the analyzer by checking only two points. There is no requirement for a reference gas during operation.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T802 comes with the NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
product
Dynamometers
When accuracy, reliability and performance matter look to the name that means dependability: A&D Technology. The comprehensive PerformanceLine includes a solution for all of the tasks of a modern and efficient test field, from durability, vehicle simulation, and high dynamic transient to high-speed e-motors. Choose from a variety of field-proven models from the PerformanceLine family with proven performance to meet your testing needs.
-
product
Rugged, Long Gauge Length Extensometers
Model 3543
Jinan Testing Equipment IE Corporation
With over 15 years of proven reliability in the world’s most demanding testing environments, the Model 3543 extensometer is designed to survive in those applications where standard axial extensometers would not. Designed by Epsilon, the Model 3543 was created to survive specimen failure by separating into two halves, thus preventing permanent damage to the module body. During operation, the upper half of the extensometer pulls out of the main body. Tapered measuring beams activate strain gaged flexures within the unit. This unique design allows long measuring ranges, yet retains compatibility with electronics for strain gaged transducers. These models offer high accuracy and are light weight but rugged, with low operating force. They are tension only units.The units have hardened tool steel knife edges. Standard quick attach wires provided with the extensometer work on flat specimens up to 12 x 31 mm (0.5 x 1.25 inch) and on rounds up to 25 mm (1 inch) diameter. Optional quick attach kit wire forms are available for use on larger samples. See Model 3542L for long gauge lengths with smaller measuring ranges.The Model 3543 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Combustion Efficiency Analyzers
Test Products International, Inc.
Determine combustion efficiency, CO2, and CO air free. Some models include built-in differential manometer, combustible gas detection, PC communication, data logging, and can measure NO / NOX.
-
product
Measuring Benches
• Modern design and Bluetooth® transmission integrated• The bench tables are designed to check dimensions up to 50 mm (depends on model)• These bench tables can be equipped with different kind of tables to fit your needs as well as with several types of anvils of any shapes• A ball bearing, an adjustable and reversible measuring force, as well as many other features and accessories make these tables a must for your workshop or your inspection room• Adjustable measuring force
-
product
Ultrasound Transducers
Utilizing optical and semiconductor fabrication techniques, Imaginant manufactures the PureView PrecisionTM line of RoHS-compliant delay-line ultrasound transducers with center frequencies ranging from 50 MHz to 250 MHz (higher and lower transducer frequencies are also available). Imaginant's precision-manufacturing process produces transducers that exhibit high reliability and high uniformity from device to device. This manufacturing consistency enables uniform test system performance to be attained across multiple systems. Imaginant transducers are available in focused and flat-face models that can be produced with minimal-damping for applications requiring maximal sensitivity or with maximal-damping and high-bandwidth for applications requiring the highest-degree of temporal precision.
-
product
Unequal Split Power Tappers
Pasternack unequal split power tapper product designs are also known as unequal couplers, power dividers or splitters, cross band couplers and signal samplers. Many of our unequal couplers / tapper series are RoHS and REACH compliant. Unequal RF tappers from Pasternack are available with 4.1/9.5, 4.3-10, 7/16 DIN and Type N connector options. These unequal split power tapper components for RF are manufactured to precise specifications required for accurate specified values listed for each product. Unequal split tapper products work with high power of up to 300 watts depending on style. Frequency ratings for unequal power splitter line are wide band components with a 380 MHz to 6 GHz frequency range, based on model selected. Pasternack RF power tappers in unequal design can be ordered with various directivity (dB) values of 4.8dB, 5dB, 6dB, 7dB, 8dB, 9dB, 10dB, 11dB, 12dB, 13dB, 15dB, 16dB, 20dB, 30dB depending on model. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this unequal split power tapper/coupler/divider series for RF is in-stock. These unequal split power tappers are not just in stock, but they will also ship the same-day are they are purchased.
-
product
Vector Network Analyzer Extenders
Our Vector Network Analyzer Extenders (VNA Extenders) allow high performance frequency extension of vector network analyzers into the THz range. The available models cover a Frequency Range from 50 GHz up to 1.1 THz. Contact RPG to discuss VNA Extender configurations that will gain the best performance for your application.
-
product
Programable DC Power Supply
ADG-L Series
14 models and three different output power, 4kW, 8 kW and 12 kW. Utilizing PWM technology, ADG-L delivers stable output and precise measurement. With CV, CC and CP mode, ADG-L series is ideal for Photovoltaic, Electric Vehicle, battery, fuse/capacitor and third party laboratory testing.
-
product
Linear Actuators
Electrak Pro
Thomson introduces our Electrak Pro Series of linear actuators. This family stands alone when it comes to the toughest and most demanding applications. Available in 12 or 24 VDC models with customizable stroke lengths up to 300 mm (12 in), these units can push or pull loads up to 4448 N (1000 lbf) at speeds of 20 mm/s (0.8 in/s) and hold loads up to 9000 N (2000 lbf), or contact our factory for longer strokes or higher loads. When space is scarce, where dust, dirt, and water are abundant and when solid, reliable and maintenance-free operation is a must - Electrak Pro is the answer.
-
product
Diversity Receiver
R400a
The R400a is a high performance, triple-conversion, frequency synthesized, UHF receiver fully compatible with all Lectrosonics 400 series transmitters, and a number of analog models. The proprietary audio processing includes a DSP (digital signal processor) for very low distortion and a superior signal to noise ratio. The DSP eliminates a compandor and its artifacts to provide exceptional audio quality when operating in its native hybrid mode. Special DSP algorithms also provide compatibility modes for use with Lectrosonics 100 and 200 Series analog transmitters.
-
product
T3DSO2000A Series Oscilloscopes
T3DSO2000A Series
Teledyne Test Tools T3DSO2000A Oscilloscopes feature two channel and four channel models with analog bandwidth options from 100 MHz to 500 MHz. Each model offers a maximum sample rate of 2 GSa/s, and a maximum memory depth of 200 Mpts in half channel mode. All models incorporate two 2 GSa/s ADCs and two 200 Mpts memory modules. When all channels are enabled, each channel has sample rate of 1 GSa/s and a standard record length of 100 Mpts. When only a single channel per ADC is active, the maximum sample rate is 2 GSa/s and the maximum record length is 200 Mpts. For ease-of-use, the most commonly used functions can be accessed with its user-friendly front panel design.
-
product
Installation Testers
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
product
Broadband Seismometer
KS-2000M / KS-2000BH
*1000 V/(m/sec) sensitivity (other sensitivities on special order). Three-component. 120 s to 50 Hz (other cut-off values possible). The Geotech Model KS-2000 is a new broadband seismometer based on the time proven Model KS-54000. Its small dimensions make it ideal for portable applications.
-
product
Current Injection Sets
Built in c based Time Interval Meter measuring from1 millisec to 9999 sec. Panel with easy and clear legends to read. Continuosly variable outputs. Auto Cut-off & output isolated. Self sensing of contacts i.e. NO or NC Potential free star stop signals Available in Portable / Lab type models with metal cover
-
product
Model Quality Assurance (MQA)
Model Quality Assurance (MQA) is an automated SPICE model validation software which allows you to check and analyze SPICE model library, compare different models, and generate quality assurance (QA) reports in a complete and efficient way. With more than ten years of history, MQA has become the industry standard for SPICE model acceptance and signoff and is widely adopted by leading integrated device manufacturers (IDMs), foundries and design houses.
-
product
Electronic Potential Divider
• Provides many ratios over a wide range • Small ratio and phase errors • Models operating at different voltages are available
-
product
Paramagnetic Oxygen Purity Analyzer
Model 3010MA
Teledyne Analytical Instruments
Teledyne's Model 3010MA Paramagnetic Percent Oxygen Analyzer is a versatile, microprocessor-based instrument specifically designed for oxygen purity analysis. Drawing on the solid performance of Teledyne's 3000 Series control platform, the 3010MA provides the user with a wide variety of features while maintaining cost effectiveness.
-
product
IndySoft for Calibration Management
The IndySoft Calibration Management workflow offers a rich feature set to manage the entire lifecycle of your quality assets. With support for leading enterprise platforms it's perfect for deployment in the corner lab of a startup manufacturing facility or a multi-site international quality-driven operation. With the IndySoft exclusive process modeling engine, companies can re-configure the event-driven workflows with checkpoints, rule sets, and documentation at every point along the equipment path, ensuring assets are handled according to their exacting requirements.
-
product
Calibration & Demag.
Model 990A/990C
The Model 990 Series Magnetreaters® are highly accurate, pulse type, ringing demagnetizers (also called treaters) for the controlled stabilization of permanent magnets and permanent magnet assemblies. Regardless of line voltage stability, they provide a controlled output through continuous pulse amplitude regulation. Treating voltage is variable from 0 to 600 VDC. Additional energy can be added to the Model 990 Series by interconnecting a Model 992 Energy Booster. The energy level is increased from 18 to 36 watt-seconds. With this option, treating coils will produce higher demagnetizing fields and lower ringing frequencies, which can provide greater field penetration in some applications.
-
product
Glass Thickness Meters
Shenzhen Linshang Technology Co., Ltd.
As a supplier of laser glass thickness gauge and glass thickness measuring tool, Linshang provides two models of glass thickness gauge that can be used to measure the thickness of various glasses, i.e: single-layer glass, double glazing, triple glazing, multilayer glass, LOW-E glass, and insulating glass, especially suitable for installed glass, such as doors and windows, curtain wall glass, etc.. It can measure the glass thickness as well as the thickness of air space (between the glass). The glass check works on the basis of reflection in the glass.
-
product
Banana Plug Test Clip
PCS
The PCS-MB Parrot Clip model is a Banana Plug Test Clip of a medium size, with a length of 70 mm, including the metal tip and the button. Its weight is 7 g, Due to the banana connection the PCS-MB Parrot Clip can be connected to different cable leads. This is convenient when you want to use different clips like alligator clips or parrot clips or just the banana plug at the leads. The PCS-MB provides also reliable hands-free connections for different component sizes from SMD with the W1 tip up to the W4 tip.
-
product
Tunable, Pulsed IR SW & LW OPO IR Source
Firefly-IR
Firefly IR is available in short-wave and long-wave models, providing broad wavelength coverage from 1.4-8.5 µm. The compact and sealed design requires no manual alignment, and can be used in a variety of applications in the lab and in the field. Wavelength selection and scanning is automated and performed via web browser or using a TCP/IP command set. Pulsed operation and high repetition rate provide high peak power and rapid data acquisition.
-
product
2WD Dynamometers
MD-100 SERIES
Our pioneering experience has led us to be the world leader in the design and manufacturing of durable dynamometer equipment that stands the test of time and the 100 model has been one of our most durable models. Mustang has supplied over 50,000 variants based on the 100 chassis over the last 25-years and we estimate that about 1.5 billion tests have been performed on the 100 model during this time. The 100 series offers the small shop owner the right equipment for road testing and power checking of today’s modern automobiles and pick up trucks. The 100 is offered at an attractive price and with features that meet the needs of repair professionals more concerned with repairs than performance tuning. The 100 is also an excellent choice for high schools and colleges as it can be used for educational purposes. Optional emissions testers can be added to teach students how to use the dynamometer for reducing emissions. The 100 can be installed in a pit or paired with Mustang’s lightweight composite ramps for installation above-ground.
-
product
ESD & Latch-Up Test Service
MASER Engineering has automatic test equipment for the most common ESD test pulse models. MIL - JEDEC - ESDA - IEC standards. IC level Human Body Model. IC level Machine Model. IC level Charged Device Model. System level IEC 61000 HBM. AEC-Q100 Field Induced Gate Leakage test. Static Latch-Up test. Dynamic Latch-Up test.
-
product
PXI Vector Signal Analyzer
PXI Vector Signal Analyzers feature a wide frequency range, real-time signal analysis, and advanced signal processing. PXI Vector Signal Analyzers can perform measurements for a broad range of wireless technologies such as GSM, EDGE, WCDMA, LTE-Advance Pro, 5G, Wireless LAN, and Bluetooth. Select models also feature a LabVIEW-programmable FPGA that you can customize for advanced measurement applications. PXI Vector Signal Analyzers are ideal for microwave test, wireless test, RADAR test, spectral monitoring, software-defined radio (SDR), radio monitoring, interference detection, signal intelligence, and other applications.
-
product
Spectroscopic Ellipsometer Software
SpectraRay/4
SpectraRay/4, the SENTECH proprietary spectroscopic ellipsometry software, includes data acquisition, modeling, fitting, and extended reporting of ellipsometric, reflection, and transmission data. It supports variable angle, multi-experiment, and combined photometric measurements. SpectraRay/4 includes a huge library of materials data based on SENTECH thickness measurements and literature data as well. The large number of dispersion models allows modeling of nearly any type of material.
-
product
Intelligent Remote Terminal Unit
The ADAM-3600 is a new series of ADAM models which leverage IoT technology for RTU applications. They not only have high environmental adaptability, to work in, far and wide remote locations, but also has a new form factor that is ideal for installation in remote terminal units.
