Model
construction of a concept.
See Also: Modeling, Modelling, Modelers, Human Body Model, Charged Device Model
-
Product
- RS-422 Opto Isolation Module
Model 8381
-
FEATURES: Opto Isolation; Built-in Power Supply; 115.2 KBPS Data Rate; DIN Rail Mounted; Full Duplex; Programmable Terminations. The Model 8381 RS-422 Opto Isolator allows re-generating and extending the distance of RS-422 networks while maintaining optical isolation between the ports. Model 8381 allows for the extension of RS-422 links to a maximum limit of 3,300 feet or 1 km at any data rate up to 115 KBPS.
-
Product
NIST Calibration for D620-A
D620-A-CCNIST
-
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
Product
Diametral Extensometers for Rock and Concrete Testing
Model 3975
-
Jinan Testing Equipment IE Corporation
Designed for accurate measurement of small diametral strains such as those required to determine Poisson’s ratio of rock, concrete and asphalt samples. The units are designed to be used in conjunction with the Model 3542RA axial averaging extensometer.
-
Product
Biconical Antennas
-
For many years most standards called for the use of a half-wave dipole antenna set for frequencies above 80 MHz. However, to reduce test time, broadband antennas such as the biconical antenna and log periodic antennas began to be accepted. Broadband antennas, compared to half wave dipoles, reduce test time because the technician did not have to stop the test to adjust the dipole antenna for each frequency. A.H. Systems'' 7 models of Biconical Antennas operate efficiently over the frequency range of 20 MHz to 18 GHz. Suitable for FCC, MIL-STD, VDE, TEMPEST, and immunity testing, each Biconical antenna will provide reliable, repeatable measurements.
-
Product
NI Electric Motor Simulation Toolkit
-
PMSM, ACIM, SRM, and power inverter models for high-performance simulationHigh-fidelity simulations with support for user-defined parameter lookup tables or JMAG-RT models. Open software for full flexibility and customizationLabVIEW project templates to build a software-only simulation and hardware-in-the-loop application. Direct integration with NI VeriStand for configuration-based real-time test. Models for desktop simulation, LabVIEW Real-Time simulation, and FPGA-based simulation
-
Product
150 A, 5 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 6 Meter Cable
CP150-6M
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
Man in the Middle Cable
MitM
-
The Man-in-the-Middle Cable (Catalog No. MitM) was created to work with the T4000 and T4350 to enable a technician to use an electric vehicle rather than a very large load emulator to absorb the energy delivered by the DC fast charger during charger testing. It currently comes in 350 Amp CCSI and 200 Amp Tesla/NACS models, each with charging connector holders and digital temperature sensors.
-
Product
2-Ch 1 GHz A/D and D/A with Virtex-7 FPGA - 6U VPX
Model 58730
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One or two 1 GHz 12-bit A/D- One or two 1 GHz 16-bit D/A- 4 or 8 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface up to x8- Dual-µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
DC Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
DC load banks for all voltage levels and power test applications, available in a variety of models including portable and fixed models.
-
Product
Very High Speed Pulse Generators (Rise Time ≤ 1 ns)
-
The Avtech high speed pulse generator line includes models with rise times as low as 40 ps! Instruments are available in a variety of formats, including DC-powered externally-triggered modules, simple AC-powered benchtop pulsers with knob and switch controls, as well as more sophisticated instruments with GPIB,
-
Product
MirrorLink Test System
Catena 2210
-
The Catena 2210 is a test tool with two USB Network Control Model ("NCM") devices. These devices create a bridge between two USB hosts. Validation testing is made possible by connecting a test control computer to the USB host being tested. Ethernet traffic from the test host is transferred through the Catena 2210 device to the control host, and vice versa.
-
Product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4I.2211-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Basic Basic Butt Set For Phone Line Testing
BSX200
-
Triplett Test Equipment & Tools
BSX200 Basic Butt Set is designed for people who occasionally need to deal with dial tone but don't require all of the features of an expensive model. The BSX200 provides user with dial tone, dial out, Caller ID, last number redial, on/off hangup button, flash button, DTM and FSK support, and three ways to connect to the line: an RJ11 connector, high quality alligator clips, and a type 66 adapter.
-
Product
Aerospace Onboard Software Modules
ADS2 for Aerospace
-
Your product description goes here. The Aerospace Onboard System Development Process is guided by SAE ARP4754A. It consists of multiple levels of specification, design, validation and verification and is distributed between OEM and multiple suppliers of systems, subsystems and components.Due to the complexity of the development process, a consistent platform supporting model based validation, virtual and physical integration as well as requirement based verification at each level is of great importance for the industry.
-
Product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2204HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
Pulse Generator
Traction Wheel Assembly
-
The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies. • Square-wave frequency output, NPN open-collector • 5-28 VDC powered • 1 to 1,270 pulses per revolution (PPR - specify when ordering) • Optional bi-directional (quadrature) output models • 3 models: black neoprene rubber, smooth polyurethane, and diamond knurled aluminum tread
-
Product
DC Power Supplies
Asterion DC ASA Series
-
AMETEK Programmable Power, Inc.
The Sorensen™ Asterion® DC ASA Series is the newest addition to the Asterion platform of power testing solutions. The new ASA Series features three independent, isolated 600W channels for a combined 1800W total output power. The autoranging supplies feature expanded current and voltage range at the full output power level, enabling the ability to satisfy a wider testing need without requiring the purchase of additional models.
-
Product
Lightning Masts
PLP- 32
-
PLP- 32 Lightning Masts are recommended for a wide range of lightning protection applications where it is impossible or undesirable to attach conventional lightning terminals. Other models in the series share the same attributes and differ only in height and weight.PLP-32 Lightning Masts provide a cone of protection within which lightning charges are diverted to the mast and grounded instead of to the protected object. Multiple PLP-32 masts may be used to protect extended areas. Protected areas may be determined by use of the widely accepted “rolling sphere” concept. For example, a single PLP-32 mast will protect 9 foot (2.14 m) high portable buildings wholly within a 40 foot (12.19 m) radius. An array of five PLP-32 masts will protect a camp of portable buildings within a 25,000 square foot (2323 m2) area. Consult LBA Technology™ for specific layouts you wish to protect.
-
Product
Prototyping Kit
VXI-5502
-
* VXI-5502 has a Sea-of-holes Prototyping Board with multiple power and ground planes for analog and digital prototyping applications.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
Computer Controlled, Solid-State RF Switch Matrices
-
PMI offers a full product line of RF Switch Matrices that operate over the 20MHz to 40GHz frequency range. Three standard models are offered that cover this frequency range, namely 20MHz to 3.0GHz, 2.0GHz to 18.0GHz, and 18.0GHz to 40.0GHz. Any of the three models can be supplied as either a 4 X 4, 8 X 8, 16 X 16, or 32 X 32 non-blocking matrix.
-
Product
High Voltage Surge Current Monitors
HVSCM
-
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
Product
High Power Single And Dual Directional Couplers
-
Pulsar Microwave manufactures a line of single and dual directional couplers specifically designed for high power operation. There are various narrow and broadband designs from 0.1 MHz to 10 GHz. These directional couplers come in standard values of 30, 35, 40 and 50 dB with coupling tolerance of +/- 1 dB.The high power directional couplers have low insertion loss. Coupling flatness is maintained at +/- 1 dB or less among models. Most units hold a mainline VSWR of 1.2:1 or better throughout the operating frequency range. Pulsar Microwave has designs up to 2.5 kW input power. Typical directivity is 20 dB or more.Standard outlines are available with SMA or N type female connectors. For higher power ratings, typically the mainline will use N connectors with SMA on the coupled ports.
-
Product
Torque Sensors
-
Industrial-grade torque sensors and thrust cells for every application. Flange to shaft mount models, surface key mount models, shaft mount models, flange mount models, and more.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Standard Series
-
When it comes to winding resistance measurement on three-phase power transformers and autotransformers, TWA Standard series offers some of the most technically advanced instruments with LCD display in the market. Both models are capable of testing six transformer windings with a one-time cable connection, as well as three-phase automatic transformer demagnetization. The stored magnetic energy is safely automatically discharged at the end of the test. The built-in tap changer control unit enables automated test mode, where the instrument operates the tap changer without operator input and records winding resistance results based on pre-selected stabilization criteria. This option makes the operator’s job significantly easier.Both models can output test currents from 5 mA to 25 A DC for the purpose of winding resistance measurement. TWA40D has a special test mode for checking the synchronization of on-load tap changers with three phases simultaneously tested in parallel, in which the total test current can rise to up to 40 A DC.TWA40D has additional advantages when it comes to non-intrusive tap changer analysis. The unique DVtest method enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, simultaneously with the measurement of tap changer motor current which helps with the detection of motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or on three phases simultaneously. It can also be performed as an additional test simultaneously with the winding resistance test in all tap positions.An additional unique advantage of TWA40D is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer (connected in a YN configuration). This can significantly shorten the total testing time – for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.The test leads for TWA three-phase transformer winding ohmmeters are interchangeable with the TRT turns ratio testers, which means that both sets of tests can be performed with a single test lead connection to the power transformer terminals.
-
Product
Bi-Directional Amplifiers
-
Fairview’s bi-directional amplifier models are designed for use in both commercial and military applications and will support any signal type and modulation format such as 3G and 4G telecom, WLAN, OFDM, DVB and CW/AM/FM. Fairview’s bi-directional amplifiers offer high power density, efficiency and linearity in small lightweight environmentally sealed packages with SMA connectors. These units also feature a quick-connect circular locking connector for DC and control functions and each design uses a single voltage supply with voltage regulation.
-
Product
Combination Tester
Focus-4000
-
Programmable power supply（User can select big volume or high accuracy model）Fixed power supply (5V/12V/24V acceptable)High accuracy current measurement(MAX 2A) - FX710Voltage measurement MAX 16points(within +/-60V) - FX710Short relays 16pcs (MAX current 1A) - FX62024CH digital input output pins(8pcs per unit, IN/OUT setting) - FX700/FX71016 open corrector output for controlling external relays16 port (simultaneously 2 ports ) Oscilloscope channel for observing wave formCommunication function RS232C/GPIB（Standard）、CAN/LIN communication, Programmer(Options)Focus-2000Plus unique in-circuit Test（ICT）function
-
Product
Pulsed X-ray technology
-
Golden Engineering X-ray generators are based on Pulsed X-ray technology. Pulsed X-rays generate a high intensity X-ray burst (pulse) in a very short period of time (10 to 50 nanoseconds depending on the model). The output dose of each pulse is 3-6 mR measured 12 inches from the front of the X-ray generator. The operator varies the overall dose of each exposure by changing the pulse setting. The pulse rate varies from 10 pulses per second to 25 pulses per second depending on the model. The generators can fire up to 200 pulses before a four-minute rest period.
-
Product
Dissolved Ozone Analyzer
Model 470
-
Teledyne Advanced Pollution Instrumentation
The Model 470 is a state-of-the-art Dissolved Ozone Sensor designed for semiconductor Wet Bench tools and many other industrial processes. It provides continuous measurement of dissolved ozone in deionized water or sulfuric baths with concentrations up to 150 mg/L. The Model 470 is “clean-ready” for high purity semiconductor processes, and is designed to be simply spliced in-line in the recirculation loop of any wet bench tool with flow rates up to 150 SLPM.
-
Product
Demonstration Boards
SAMPULSE50GHz and SAMPULSE70GHzANT
-
The SAMPULSE50GHz and SAMPULSE70GHzANT are demonstration boards for Furaxa InP single channel sampler/pulser ICs. The SAMPULSE50GHz model contains a 2.4mm combined TDR input/output connector to the common sampler/pulser node in the IC. The SAMPULSE70GHzANT is similar, except that instead of a single-ended 2.4mm connector, the sampler IC's differential inputs are fed from a bowtie antenna. In both models, the IC's differential sampler output is converted, using an AD8009 op amp, into a single-ended ground-referenced output that is sent to an SMA jack labeled SAMPLER OUTPUT.
-
Product
Multi-Channel Anemometer
1550/1560 Series
-
Kanomax Multi-Channel Anemometers are research-grade airflow measuring instruments designed for high performance and precision. When coupled with our highly accurate probes this four-channel anemometer provides highly accurate and reliable data readings. It features a LCD display that displays the data from each channel. The Our 1550 & 1560 models house module bays for the connection of up to 24 channels (model 1560) or 64 channels (model 1550) of simultaneous air velocity measurements. Each bay accepts one of five unique modules allowing for a wide variety of custom configurations for air velocity, temperature, and humidity measurement. For a larger system, you can connect up to 5 units in a cascade for up to 320 air velocity channels and transfer the data to your company computer.
