Semi
active or passive elements connected as an electronic circuit using a crystalline subtance, eg. silicon or germanium.
See Also: E84
-
Product
16G SO-DDR4-3200 1GX8 1.2V SAM -20~85℃
AQD-SD4U16GN32-SE1
-
SAM Original Chip, Industrial Design for Improved Reliability, PCB: 30μ gold finger, Anti-sulfuration, Semi Wide-temp Support -20~85℃.
-
Product
PXI/PXIe Semi-Dynamic Digital I/O Module, 64-Channel
Digital I/O
The 40-419-001 (PXI) and 42-419-001 (PXIe) are a 64-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Semi-Rigid Test Probes Up to 6 GHz
-
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
Product
Mobii Media Encoder
-
The Smart Encoder is designed for semi and permanent based on-site installation. Deployed into sport stadiums/arena’s, Broadcast production sites, Data Centers and Outside Broadcast vehicles, the Smart Encoder will ingest a variety of input video sources such as SDI, NDI, SRT, MPEG-TS. The encoder will ingest, synchronize, encode and upload Microblock streams to the nearest cloud regional edge cluster for global distribution via the Co-Ordinator, or output a variety of streaming formats to local network for on-site usage.
-
Product
6TL29 Semi-Automated Test Platform
AQ377
Test Platform
- Compact, transportable and modular test platform.- Ready for ICT, FCT, Boundary Scan, HiPot, Vision or any combination of the previous technologies.- Mass interconnect 9025 Receiver from Virginia Panel.- 100% Compatibility with Inline Test Fixtures (P/N: AT799, AN133 and EB773).- Free available rack space: 47U height- Multi-stage pressure at 3 levels.- FastATE Technology & YAV Modules compatible.- Phi6 Dispatcher Interface.- CE Compliant.
-
Product
Film Frame Test Handler
4170-IH
-
High throughput ・High withstand load, and high thrust table ・Expansion of the strip attachment area ：260(L) X 300(W) [Withinφ300mm for WLCSP]・LOT control by barcode/2D code reader ・Easy device type exchange only test socket and display screen setting・Auto-cleaning function unit is installed to clean the socket at any desired timing.・8/12 inches ring conversion ・S2/S8 regulation compliance・SEMI G85 compliance・SECS/GEM compliance
-
Product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
-
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
-
Product
Semi-Rigid Cable Set, 3.5 Mm (Test Port) To 3.5 Mm
85131D
-
The Keysight 85131D is an 53 cm (21 in) long1 semi-rigid cable set composed of a 3.5 mm female2 to PSC-3.5 mm female connector and a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss of 16 dB or better. Insertion loss is 0.3 * sqrt(f) + 0.2 dB, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85131D is less than 0.06 dB and phase is 0.16 * f + 0.5, where f is frequency in GHz.
-
Product
Semi-automatic Three-phase kWh Meter Test Bench
SY8310
-
Hong Kong Songyang Industrial Ltd.
The new SY8310 series semi-automatic three phase energy meter test board, designed according to International Standard, is a newly developed ideal measuring equipment for energy meters. The equipment can be operated easily through test board button to preset directly all data of meter under test and test process.
-
Product
Flexible Current Sensor Probe
CTA
-
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
-
Product
Semiconductor Package Wind Tunnel
WT-100
-
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
Product
16G DDR5-5600 2GX8 1.1V SAM -20~85℃
AQD-D5V16GN56-SBH
-
SAM Original Chip, Industrial Design for Improved Reliability, PCB: 30μ gold finger, Anti-sulfuration, Semi Wide-temp Support -20~85℃.
-
Product
Trace Moisture Analyzer
PPM1
-
Model PPM1 is a trace moisture analyzer designed specifically for monitoring moisture levels in dew point and PPM units. This trace moisture analyzer utilizes an electro-chemical (P205) sensor in combination with a proprietary semi permeable diffusion membrane.
-
Product
Receiver Semi-Kit
75-NS-3
-
National RF’s 75-NS-3 receiver is a complete super-hetrodyne mini high frequency receiver, designed specifically for the short-wave listener, electronics enthusiast or radio amateur, who wants to use their hands and build a radio. The receiver is offered as a semi-kit in which the electronic assembly is loaded and functionally tested at the National RF facility. The customer must then go to the grocery store (yes…the grocery store!), procure a can of lunch meat, eat it or give it to the dog, and then proceed to drill and paint the can, in order for it to become the receiver’s enclosure! As the name of the preferred potted meat can has a registered trademark by Hormel Foods, Inc., it won’t be mentioned on this web-site. However, the name of the product is synonymous with unwanted email!!! In addition, there are other food products that might be found that are packaged in the same metallic enclosure. Detailed drilling instructions and final assembly instructions are provided as part of the kit. All other parts required for completion of the receiver are provided as well. Recognizing that the finished assembly looked somewhat like the fabled Collins receiver of the ‘60s, the 75S-3, (particularly when the can is painted a light gray) National RF engineers dubbed it (with tongue firmly planted in cheek, of course) the 75-NS-3! Although we have had fun packaging this receiver in a lunch meat can, it is nothing to turn your nose at! Its performance and portability will surprise you, and it is an ideal radio to bring with you on any trip!
-
Product
PXIe Semi-Dynamic Digital I/O Module, 32-Channel
42-419-003
Digital I/O
The 40-419-003 (PXI) and 42-419-003 (PXIe) are a 32-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Semi-automatic Semiconductor Probe Assembly Equipment
-
The components of the incoming parts are pre-assembled and preloaded to two packages. We use a high-speed four-axis robot equipped with high-precision multi-sensor grips to grab these pre-assembled subcomponents. Under CCD visual guidance, a set of rotary grab devices is equipped to capture top plunger. The device uses a multi-set CCD visual module to ensure accuracy, and the positioning accuracy of each motion link is controlled within 15um.
-
Product
Hydraulic Universal Testing Machines
UH-X/FX Series
-
Environmentally and operator friendly state-of-the-art universal testing machine The operability and visibility of the computer-controlled hydraulic servo type universal testing machine (UH-X) and the high-performance universal testing machine (UH-FX), equipped with front opening type hydraulic grips, have been greatly improved by the adoption of a large color touch panel. Equipped with a semi autotuning function that automatically adjusts the control parameters, stress control and strain control (ISO 6892 compliant) can be easily carried out without the need for a preliminary test. The UH-Xh and UH-FXh models feature a new hybrid hydraulic oil source that reduces the required quantity of hydraulic oil, thereby achieving a major reduction in electrical power (about 50 %).
-
Product
8G DDR5-5600 1GX16 1.1V SAM -20~85℃
AQD-D5V8GN56-SCH
-
SAM Original Chip, Industrial Design for Improved Reliability, PCB: 30μ gold finger, Anti-sulfuration, Semi Wide-temp Support -20~85℃.
-
Product
Semi-automatic tensile testing machine
-
The controller of this testing machine automatically applies an appropriate load and puts the extensometer between the gauge lines, etc. after the sample is set. It provides measurement with high repeatability.
-
Product
Semi-automatic Single Phase Close Link kWh Meter Test Bench
SY8120
-
Hong Kong Songyang Industrial Ltd.
The SY8120 new series semi-automatic single phase energy meter test board, designed according to International Standard, is newly developed ideal measuring equipment for energy meters. The equipment can be operated easily through test board button to preset directly all data of meter under test and test process.
-
Product
Host emulator
E84
-
Precision Development Consulting Inc
A USB controlled and self-powered emulator for functional testing SEMI E84 implementations. (E84-1000) This was developed because there was nothing like it in the marketplace, and it was clearly needed. This product enables a factory automation engineer to perform E84 functional testing anywhere in the world. Weighing less than 5oz, it is neither a burden, nor a power hog. You will never need to look for an additional power receptacle in the fab. The emulator gives the user full control over the sequence so that any test can be performed. Existing products were large and unwieldy, and provided canned tests that could not be modified to meet the requirements that Fab managers impose on their suppliers.
-
Product
PXIe Semi-Dynamic Digital I/O Module, 16-Channel
42-419-004
Digital I/O
The 40-419-004 (PXI) and 42-419-004 (PXIe) are a 16-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
Semiconductor Test System
TS-960e
Test System
The GENASYS Semi TS-960e PXI Express Semiconductor Test System is an integrated test platform that offers comparable system features and capabilities found in proprietary ATE systems. Available as a bench top system or with an integrated manipulator, the TS-960e takes full advantage of the PXI architecture to achieve a cost-effective and full-featured test solution for device, SoC and SiP test applications.
-
Product
Sapphire 3D Microscope
WDI-2000
-
The Sapphire 3D Microscope: HS-WDI-2000 was designed with high quality lighting parts and a good optical system design,can get a very clear image.with the digital camera,it can provide the image in time, widely used in LED,Solar,SEMI…
-
Product
Semi-auto 4 Point Probe System for Solar Cell Substrate
RG-100PV
-
*Measurement system for thin film on substrate samples for multi-points measurement*Even pitch and random pitch for Max.1,000 points*2-D/3-D square mapping software for even pitch
-
Product
300W to 1800W - Single Output
HWS Series
-
*Limited Lifetime Warranty*UL 508 approved*SEMI F47 Compliant (high line AC)*Universal Input (85 - 265VAC)*High Efficiency*Class 1 Div 2 option (/RY suffix)
-
Product
MOSFETs, MESFETs, and Schottky Diodes
Semiconductor Module
-
The Semiconductor Module allows for detailed analysis of semiconductor device operation at the fundamental physics level. The module is based on the drift-diffusion equations, using isothermal or nonisothermal transport models. It is useful for simulating a range of practical devices including bipolar, metal semiconductor field-effect transistors (MESFETs), metal-oxide-semiconductor field-effect transistors (MOSFETs), Schottky diodes, thyristors, and P-N junctions.
-
Product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
Test Port Cable
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
Product
PXI Semi-Dynamic Digital I/O Module, 64-Channel
40-419-001
Digital I/O
The 40-419-001 is a 64-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
