Semi-conductor
active or passive elements connected as an electronic circuit using a crystalline subtance, eg. silicon or germanium.
-
Product
Physical Vapor Deposition Systems
-
Physical Vapor Deposition (PVD) systems use physical processes, like sputtering and evaporation, to deposit thin films with exceptional purity and control. These techniques are widely used in semiconductor manufacturing, optical coatings and protective applications.
-
Product
Pulsed IV-Curve Solutions
-
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
Product
2MP HDR Jetson TX2/TX1 Camera Board
E-CAM20_CUTX2
-
e-CAM20_CUTX2 is a 2MP HDR camera board for NVIDIA® Jetson TX2 /TX1 developer kit. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). It enables an excellent low-light performance and can capture images even under 0.5 lux. e-CAM20_CUTX2 is based on 1/2.7" AR0230AT CMOS image sensor from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Product
Non-Linear Junction Detector
ORION™ HGO-4000
-
The ORION HGO-4000 is REI’s original high gain Non-Linear Junction Detector for special applications. The ORION HGO-4000 can locate listening devices and semiconductors in walls floors, ceilings, fixtures, furniture or containers and provides a user the capability to detect hidden electronic devices, regardless of whether the device is radiating, hard wired, or even turned off.
-
Product
Deskew Calibration Source for CP030, CP030A, CP031, CP031A, AP015, CP150, CP500
DCS025
-
The DCS025 Deskew Calibration Source generates time-aligned voltage and current pulses for precise deskew of voltage and current probes.This is critical for measurements in which small propagation delay differences between probes can have a large impact on a calculated measurement, e.g., instantaneous power semiconductor device loss measurements.
-
Product
IC Product Testing & Analysis Services
Integrated Service Technology
-
Integrated Service Technology Inc.
iST (Integrated Service Technology Inc.) is a leading lab-service company, specializing in the development of IC product testing & analysis, failure analysis, debugging, reliability test, material analysis. Apart from developing testing technologies for the upstream IC design and semiconductor industries, iST also expanded to provide a full-spectrum of services for the mid and downstream companies in the electronics industry.
-
-
Product
Edge Grinding Machines
-
The requirement for the wafer quality is getting higher and the condition of wafer edge is getting more important. The edge grinders “W-GM series” process edge grinding of various kind of materials such as Silicon, sapphire and SiC.As a solution for that, Our W-GM series are highly rated among manufactures of silicon, compound materials and other wafer shaped materials. Wafer edge grinding machine also draws the attention as a solution for the yield loss due to the knife edge of device wafer in the back end process. In the semiconductor manufacturing process, from the wafer manufacturing to the device manufacturing, the quality improvement of wafer edge is necessary in recent years.We make proposals that achieve the improvement of quality, CoO and yield with our machine.
-
Product
32-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8334
Motion Controller
ADLINK PCIe-8334 is a hardware-based EtherCAT motion controller able to support up to 32 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8334 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party SubDevice are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
Product
3.4 MP Autofocus (Liquid Lens) Low Light Camera Module
e-CAM31_MI0330_MOD
-
e-CAM31_MI0330_MOD is a high performance, small form factor, 3.4 MP Autofocus Low Light Camera Module with Liquid Lens. It is based on AR0330 CMOS Image sensor from ON Semiconductor®. This Autofocus Liquid Lens Camera Module has slave mode for precise frame-rate control and for synchronizing two sensors. e-CAM31_MI0330_MOD – Liquid lens camera module has superior low light performance. It supports Full HD @ 60fps for maximum video performance. It also has a support for external mechanical shutter and an on-chip phase-locked loop (PLL) oscillator. The dedicated ISP performs the entire Auto functions like auto white balance, auto exposure control in addition to complete image signal processing pipeline.
-
Product
RF & Microwave PXI Switch Modules
-
These switching systems are used for design validation, reliability and production test including 5G, SD radios, S parameter testing for RF cables, antennas, radar and semiconductor verification.
-
Product
DUT Boards
-
RTI designs and manufactures DUT boards for many types of special purpose test equipment including: ESD test systems, special purpose functional testers, automated curve trace equipment, as well as standard semiconductor test equipment. All designs are performed in-house using PCB design software (Mentor PADS, CAM350) and 3D mechanical design software (Solid Edge) if required. PCB fabrication is sub-contracted to one of our long-time fabrication partners.
-
Product
STPOWER RF LDMOS Transistors
-
ST offers a broad portfolio of RF LDMOS (lateral double-diffused metal oxide semiconductor) transistors operating from a supply voltage of 7 to 50 V. They target applications in the 1 MHz to 4 GHz frequency range and feature high peak power up (>1 kW) and high ruggedness capability.
-
Product
ALD Advantages
-
Atomic Layer Deposition (ALD) stands out for one reason: control. The most significant advantages of thin film deposition via Atomic Later Deposition over other methods, are manifest in four distinct areas – film conformality, low temperature processing, stoichiometric control, and inherent film quality associated with the self-limiting, and self-assembled nature of the ALD mechanism ALD is exceptionally effective at coating surfaces that exhibit ultra high aspect ratio topographies, as well as surfaces requiring multilayer films with good quality interfaces technology. This thin-film process builds materials one atomic layer at a time, delivering unmatched uniformity and sub-nanometer precision, even on complex 3D structures. That level of accuracy makes ALD a critical technology for advanced semiconductor manufacturing, flexible electronics, and materials research.
-
Product
LXI High Voltage Matrix 2-pole 300x2
60-310-302
Matrix Switch Module
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
Non-Contact Chemical Concentration Monitor
CS-900
-
In order to fulfil the tight chemical concentration control required in semiconductor WET process, HORIBA realizes higher functionality to meet the needs by designing compact equipment while maintaining stable measurement and carrying out operator safety through its original sensor design.
-
Product
LXI High Voltage Matrix 2-Pole 100x2
60-310-102
Matrix Switch Module
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing. The 60-310 is designed in accordance with the LXI Standard 1.4 and is supplied in a 2U high, full rack width case with 500mm depth.
-
Product
2MP Wide Temperature Range Industrial Grade HDR Camera
e-CAM20_CU0230_MOD -
-
e-CAM20_CU0230_MOD is a 2MP high performance, HDR Camera Module with excellent low light performance. It is based on AR0230AT CMOS Image sensor from ON Semiconductor®. It has an ability to stream seamlessly at wide temperature range (-40 to 105°C) which is suitable for Automotive application. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. e-CAM20_CU0230_MOD has a dedicated, high-performance Image Signal Processor chip (ISP) that performs the entire Auto functions (Auto White Balance, Auto Exposure control).
-
Product
Pattern Region of Interest Analysis System
PRIAS
-
PRIAS is a synergistic new imaging technique to visualize microstructure and provide exciting new views of your materials. PRIAS enables users to quickly characterize materials without requiring full EBSD pattern indexing. Through a novel use of the EBSD camera, PRIAS provides as many as 25 positional electron detectors to allow unprecedented flexibility in image collection and visualization. Applications of PRIAS include traditional EBSD materials such as metals, ceramics, semiconductors, and minerals as well as new analysis of plastics and glasses.
-
Product
Micromanipulator
XYZ 300 Series
-
Quarter Research and Development
The XYZ 300 Micropositioners provides 3-axis motion with .300" movement on each axis. Motion is controlled by three adjustment screw knobs that provide .025" resolution per turn. A general purpose micro positioner, it is intended for industrial, medical, biological, semiconductor, and general scientific applications.
-
Product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope
780319-01
Oscilloscope
1 GHz, 2 GS/s, 8-Bit, 8 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, uses a high-throughput bus to lower test times, provides picosecond-level synchronization among modules, and integrates with the entire suite of NI hardware, so you can build and customize a complete mixed-signal or high‑channel‑count test system.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
High Volume Semiconductor Substrate Interconnect Tester
GATS-2100
-
Pre-align *load *CCD camera alignment *electrical test * unload * sort of pass, opens, shorts, and alignment errors.The GATS-2100 concurrent approach provides unmatched volume capability... 2.5 seconds per device. As with all Nidec-Read Test systems, the GATS-2100 offers you the most test technologies for your requirements
-
Product
Energy Saving Static Converter
-
The ENERGY SAVING static converter serves to generate a controlled squarewave single-phase alternate voltage (low frequency: 25 ÷ 125Hz) for industrial applications requiring high load power supplied by an external matching transformer. The power supply, sectioned by remote control switch and external fuses, is fed by a three-phase electric line via uncontrolled diode bridge and filtered by inductor and capacitor battery. The DC voltage thus obtained is converted into single-phase alternating voltage via “H”-shape bridge of semiconductors in order to control impressed frequency single-phase transformers.
-
Product
Test Automation
TetraMAX®
-
The Synopsys TestMAX™ family of products offers innovative, next-level test and diagnosis capabilities for all digital, memory and analog portions of a semiconductor device. The Synopsys TestMAX family contains unique capabilities for automotive test and functional safety as well as technologies that unlock new levels of test bandwidth and efficiency by leveraging high-speed interfaces common on many designs.
-
Product
Probe Card Solutions
-
Advanced engineering solutions are required to meet increasing challenges for wafer test, driven by today’s rapid technology acceleration. Translarity offers probe card solutions for the global semiconductor and packaging test industries, tailored to customer specifications. The company’s IP portfolio, design capabilities, innovative products, and reputation for quality, reliability and customer support ensure the right solution for your testing requirements.
-
Product
Generators and Sources
-
For general purpose standalone applications or as core components in a high speed test and measurement system, Yokogawa sources and signal generators are highly accurate and functional. The integration of source and measurement into a single unit greatly simplifies the test process. Semiconductor devices, sensors, displays or batteries etc can therefore be quickly and easily characterized.
-
Product
Scanning Electron Microscope
Verios G4 XHR SEM
-
The Thermo Scientific™ Verios G4 scanning electron microscope (SEM) provides sub-nanometer resolution from 1 to 30 kV and enhanced contrast needed for precise measurements on materials in advanced semiconductor manufacturing and materials science applications, without compromising the high throughput, analytical capabilities, sample flexibility and ease of traditional Scanning Electron Microscope (SEM).
-
Product
Dynamic Power Device Analyzer/Double Pulse Tester
PD1500A
-
As an off-the-shelf measurement solution, the PD1500A delivers reliable, repeatable measurements of wide-bandgap semiconductors. The platform ensures user safety and protection of the system’s measurement hardware.
-
Product
Mixed Signal Test Systems
MTS1000i
-
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
