AXI
1) Advanced eXtensible Interface 2) Automated X-ray Inspection
See Also: Automated X-ray Inspection
-
Product
Magnetic Field Cancelling System
MK-1
-
Single axis magnetic field cancelling system for MRI scanners and biomagnetic applications. This system is used when the magnetic field sensor cannot be placed within the shielded volume. For example, in MRI applications the sensor is usually installed outside of the shielding room because of the MRI scanner's high fringe field.
-
Product
LXI 50Ω RF Matrix - 2.4GHz
Matrix Switch Module
Pickering's LXI 50Ω RF Matrix - 2.4GHz design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 16 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output. These matrices can be supplied in a variety of configurations based on Y axis sizes of 4, 8 and 16 and X axis sizes up to 32. The smaller matrix sizes in the range are factory reconfigurable up to the maximum size.
-
Product
Nanopositioner
P-616 NanoCube
-
Physik Instrumente GmbH & Co. KG
Compact Parallel-Kinematic Piezo System for Nanopositioning and Fiber Alignment. In a parallel-kinematic multi-axis system, all actuators act directly on a single motion platform. This means that all axes can be designed with identical dynamic properties, which reduces the moved mass considerably. Further advantages: It is possible to make the parallel-kinematic system more compact than serial stacked or nested systems. The errors and masses of each individual axis do not accumulate.
-
Product
CAM/GATE Test Kits
-
The Camgate ™ series test fixtures provide ‘Z’ axis motion and, with the optional floating top plate, makes this series ideal for top side probing. The floating push plate is accurately registered with two tooling/guide pins. The top plate mounting frame is adjustable in .500″ (12.7mm) increments to accommodate top side probing in the lower position, or clearance for PCA’s with tall components in the middle or top position, without the need for riser blocks. Camgate fixtures are available with the most widely used interfaces in the test industry.
-
Product
Motion Control Board, PCI
APCI-8001
-
*Axis control for 3 servo or stepper motors*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders or SSI absolute encoders*Possibility of extension to a total of 8 axes*Menu-driven test application
-
Product
Shake Table Testing
-
Response Dynamics Vibration Engineering, Inc.
Shake table testing is often used in prototype analysis, failure analysis, shipping vibration testing and vibration sensitivity testing. We know what boundary conditions are vital for effective testing, how and where to instrument the system, how to deal with for off axis excitation (often not accounted for), and make the most efficient use of testing time. Let us have a look at your system and any specified vibration criteria before the shake test is designed. We can interpret the criteria, make sure it is applied appropriately, and make recommendations that will save valuable time and expense.
-
Product
Vibration Test System
3-axis
-
This small 3-axis vibration test system has been developed in response to many customers' request for ?gcompact and easy to handle & use h multi-axis VTSs without sacrificing performances, featured by its small installation area of W900mm by D850mm, relatively quiet due to employment of small fans insterad of bolower(s), a displacement of 25mmp-p for each axis and max. transient acceleration of over 98m/s2<10G>*,
-
Product
Motor Vehicle Headlight Testers
-
Foshan Analytical Instrument Co, Ltd.
It can be used to promptly and accurately measure the luminous intensity and the illuminating position(or the optical axis deviation amount) of the high/low beam of vehicle headlight. With the lamp image alignment techique the single-machine high/low beam testing needs only 30-odd seconds.It is also used for the dual-lamp test at the testing station,the dual-machine test at the same time needs only 20-odd seconds.
-
Product
Goniophotometer For Luminaries Intensity Distribution Curve
LCG-1800
-
Shenzhen Chuangxin Instruments Co., Ltd.
Mainly used to measure FL etc. When installing luminaires, the lighting center of luminare and the rotating center of rotating table shall be at the same position. In B- coordinates, luminaire axis is superposed with the horizontal axis of rotating table. In A- coordinates, luminaire axis is vertical with the horizontal axis of rotating table.
-
Product
PXI/PXIe RF Matrix, Single 2x2, 2.5GHz, 75Ω, MCX
42-837A-101
Matrix Switch Module
The 40-837A-101 (PXI) and 42-837A-101 (PXIe) are 75Ω 2x2 RF matrices with 1 bank in a single slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40/42-837A modules.
-
Product
Additional Rotary Axis for High Precision Co-ordinate Measurement Machines, ISO 10360 Part 3 Compliant
QuadProfile
-
Rotary Precision Instruments UK Ltd
Precision rotary axes specifically developed to increase the flexibility, productivity and efficiency of your CMM.The smallest rotary table in the Quadrant range that delivers high speed measurement of smaller parts such as turbine blades and gears.
-
Product
Real Time Digital Filters
-
Real Time Digital Filters can be used to filter a measured signal in real time. Filter characteristics can be defined by the user to meet the requirements of a specific application. Real-time digital filters are applied in the data conditioning phase. The filters are designed with a graphic design tool and then uploaded to the front-end for real-time calculation. The graphic design tool defines the filter performance vertical axis with a dB scale. The horizontal axis is defined as relative frequency.
-
Product
Optical Time Domain Reflectometers
-
An optical time domain reflectometer (OTDR) is a precision instrument used to locate events or faults along a fiber link, typically within an optical communications network. The OTDR launches a series of high speed optical pulses into the fiber to be measured. Various events on the fiber generates a Rayleigh back scatter that returns to the OTDR and the strength of the return pulses are measured and integrated as a function of time, and plotted as a function of fiber length. The horizontal axis is the distance and the vertical axis is the loss.
-
Product
LXI Scalable Matrix - 2Amp 10x20 Configurable Matrix Plugin Module
65-219-206
Matrix Switch Module
Matrices are created by populating the 65-200 scalable matrix chassis with plug-in modules that provide access to the X axis on 15-pin D-type connectors and the Y axis on 50-pin D-type connectors. The chassis is capable of supporting matrices with a Y axis size of 20 or 40 and X axis sizes up to 60 in increments of 10. Users can specify as many or as few plugin modules as they require and can field upgrade the chassis to extend the matrix size.
-
Product
Rotation Field Testers
-
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. In normal use, the test leads are connected to the live terminals, with an R / L display showing the later direction of rotation of the electric motor. In addition, this model can be used for the contactless determination of the direction of rotation of switched-off or not connected motors. Place the switched-on measuring device on the motor parallel to the longitudinal axis without test leads. Now turn the shaft of the motor, the measuring device now shows a right or left movement.
-
Product
Linear Interferometer
10766A
Linear Interferometer
The Keysight 10766A Linear Interferometer is used for general purpose single axis measurements and can be employed when the interferometer is the moving component, instead of the measurement reflector. It has a rugged, thermally stable stainless steel housing.
-
Product
Image Analysis & Stage Micrometers
-
The APPLIED IMAGE series of Image Analysis and Stage micrometers are ideally suited for calibrating optical, imaging, video, and reticle-based measurement systems. Designed for ease of use and manufactured for durability, the SM Series has both English and Metric scales in one or two axis configurations. Both types of micrometers come with NIST traceable calibration standards and are available on multiples substrates to perfectly fit your needs. The experience APPLIED IMAGE has in manufacturing precision imaged optical components makes us the trusted source for standards for magnification system microscopy and vision applications. Should you need to alter feature patterns, size, or substrate, fill out our Custom Optical Components and Standards form to start the conversation.
-
Product
High Resolution Digital Radioscopy Compact System
FastRadio
-
Real time high resolution digital radioscopy. Motorized zoom axis. Horizontal flat sample holder. Very small footprint.
-
Product
Solvent Resistance Tester
NRJ-100
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008/IEC60851-4; Inspection standard: JB/T4279.10-2008Used to detect the solvent resistance performance of enameled round wires and flat wires with nominal conductor diameter above 0.250mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Pencil push unit would automatically lay down pencil and move ahead, lift pencil and automatically return to initial position;Used in combination with JRK-60 solvent thermostatic controller;Automatic pencil sharper can sharpen pencil tip to be 60° symmetrical to its axis;
-
Product
Automated X-ray Inspection (AXI)
-
Automated X-ray inspection (AXI) is a testing approach based on the same principles as automated optical inspection (AOI). Instead of cameras, X-rays are used to automatically inspect features.
-
Product
EtherCAT Master Multi-Axis Motion Controllers
DMC-52xx0
-
The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.
-
Product
Cladding Alignment Splicer
95EA
-
OFS-95EA optical fiber fusion splicer is designed with high-speed image processing technology and special precision-positioning technology. It will automatically finish the whole fiber fusion process in 9 seconds by fast mode, and splice loss is lower than 0.02dB for single mode fiber. 3.5-inch LCD, dual CMOS monitors, X and Y axis separately display or simultaneously display, thus different fusion stages can be showed clearly. It is compatible with ITU-T SM/MM/DS/NZDS/ED fiber, and is equipped with 4-in-1 holders and SOC adapter.
-
Product
Wheelset Axle Identification Using 2D DMC Codes
-
Automation of the process of identifying the axles of wheelsets at the site of the final inspection by the two-dimensional codes applied to them. The system should provide automatic search, reading and recognition of a two-dimensional code punching on the axis. The recognition result should be automatically transmitted to the ultrasound diagnostic unit as an identifier of the controlled object.
-
Product
Optical Test Instruments
OptiSpheric® & Spherometer
-
TRIOPTICS' OptiSpheric® and Spherometer are the classic optical test systems for spherical lenses that can be found in virtually any optical manufacturing process. While the Spherometer is used for the tactile determination of lens radii, OptiSpheric® systems provide contactless measurement of effective focal length, back focal length, flange focal length, MTF on axis and the radius of lenses. Specific upgrades allow determining centration errors and angles on plane surfaces. Systems for testing IOLs in compliance with EN/ISO 11979 form a class of their own. OptiSpheric® IOL R&D is preferably used for measuring single lenses while OptiSpheric® IOL PRO 2 is designed for the fully automated IOL measurement in serial production.
-
Product
SparkFun Triple Axis Accelerometer Breakout
KX132 (Qwiic)
-
This SparkFun Triple-Axis Accelerometer Breakout is a simple Qwiic breakout for the KX132 digital accelerometer from Kionix. The KX132 is a low-power, 16-bit resolution three-axis accelerometer with four user-selectable acceleration measurement ranges of ±2g/4g/8g/16g and has up to a 10kHz (max) output data rate making it ideal for a wide range of acceleration measurements as well as high-speed applications such as vibration and tap sensing.
-
Product
LXI Chassis X Plugin - 8x16 Matrix
65-110-202
Matrix Switch Module
The 65-110-202 is an 8x16 matrix plugin for the 65-110A chassis. At least one is required to be fitted to these chassis assemblies that are configured for Y=16 applications. The number of plugins is determined by dividing the X axis size required by 8 and rounding the number up to the next integer.
-
Product
Goniophotometer for Traffic Signal Lamps
LSG-1950S
-
LSG-1950S is a high automatic test system for luminous intensity distribution of luminaires and can be applied to quality evaluation and quality control for signal luminaires, luminaires for cars, motors, vessels and Retro-reflectors. LSG-1950S system is a goniophotometer which can measure all kinds of lamps and luminaires.• Rotations of test samples around both vertical axis (-90°~+90°) and horizontal axis (-35°~+35°) • Accuracy of angle: 0.1° • Resolution of angle: 0.01° • Photometer detector: CIE class A (standard class) accuracy • All software control, high intellectual faculties and simple operation
-
Product
QW-AddIn For Autodesk® Inventor® Software
-
QW-AddIn for Autodesk® Inventor® Software is a QuickWave plug-in for Autodesk® Inventor® Software, a wide-spread mechanical tool, allowing defining a complete project for electromagnetic simulation, also periodic structures and axisymmetrical structures (V2D), directly in the popular CAD environment. A set of self-explaining dialogues provides very convenient tool for setting the electromagnetic properties such as assigning the materials, adding ports, boundary conditions, setting postprocessings and excitation parameters.Automatic mesh generation using Automatic Meshing Intelligent Generation Option (AMIGO) optimises the meshing taking into account requested wavelength resolution in all media, while avoiding unnecessarily small cells. Additionally QW-AddIn for Autodesk® Inventor® Software can be used for optimisation and parameters sweep with QW-OptimiserPlus.QW-BHM is available and heating parameters can be defined together with rotation in XY plane along axis parallel to Z axis. Creating proper axis of rotation can be done by selecting edge or solid body from the project. It will contain the middle point of selected object and its location can be modified either with the mouse or by entering new coordinates.
-
Product
CAMGATE Test Kits
Series 453
-
LThe GR Series 453 CAMGATE mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 453 provides interface compatibility using the GR2270 Style, 12 block interface. This interface accepts the industry standard I/O, power, and coax blocks. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components.
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
