BER Testers
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: BER Test, Bit Error Rate Testers
-
Product
DC Resistance Tester
ZLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
Product
Optical Testers
-
Instruments used to analyze, certify, and troubleshoot fiber optic networks and components, ensuring they meet performance standards by measuring light power, detecting faults (breaks, bends, dirt), and verifying signal integrity, using tools like OTDRs, Power Meters, and Visual Fault Locators.
-
Product
Combination Board Tester
V250 / V250PXI
-
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
Product
Optomechatronics Testers
-
T100 is a flying actuator tester designed to calibrate and test any kind of device, module or product with electronic, optical and mechanical functions, using the latest opto, MEMS, sensor, microelectronics, micromechanics technologies.T100 can be equipped with tools and actuators to perform calibration, electrical test, mechanical test, optical test.All on a single machine without any need for additional equipment.It is the ideal tester for production lines with a wide variety of products and frequent entry of new ones.
-
Product
Socket Tester
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
*It tests your protection system to ensure the household electrical safety.*Widely used in the school, laboratory, factory and other social fields.
-
Product
Leakage Current Testers
-
For general-use electrical devices Built-in non-medical use networks For rated currents of up to 20A For automatic testing on production lines, etc.
-
Product
Non-Contact Voltage Tester
1AC II
-
The portable 1AC II non-contact voltage tester from Fluke are easy to use – just touch the tip to a terminal strip, outlet, or supply cord. When the tip glows red and the unit beeps, you know there's voltage present. Electricians, maintenance, service, safety personnel, and homeowners can quickly test for energized circuits in the workplace or at home and even detect miswires of an electrical outlet.
-
-
Product
Photovoltaic Testers
-
A range of products to verify safety and efficiency of photovoltaic installations. This range includes 1500V I-V Curve Tracers, Insulation testers (IEC/EN62446), designed to provide more and more functional solutions for the activities to be performed.
-
Product
Pro CABLE TESTER
PK-101/PK-101C
-
PK101 is an innovative tester to perform full cabling testing, displaying wiremap, cable ID, faults, toning and identify active network port on all common low-voltage cabling system in today's automated homes, network, telephone or video media, and determine cable run length up to 300 M.
-
Product
12V Battery Tester
1957
-
Peaceful Thriving Enterprise Co Ltd
Voltage / battery / alternator multi tester for all 12V DC systems.
-
Product
Back Pressure Tester
TU29P
-
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
-
Product
Electronic Product Testers
-
Infinity Machine International Inc.
Electronic Product Testers by Infinity Machine International Inc. - for applications such as connectors insert and extract testing machine, touch screen torsion, abrupt pull tester for power wire and headphone cable, double station electronic product cable tester, cord flexing rotary bending fatigue tester, button click electronic product tester simulation, and more.
-
Product
Parasitic Drain Tester
64970
-
Replaceable in-line fuses protect both the meter and tester in the event a high current source on the vehicle is left on. The multimeter is bypassed with the switch during connection in case of a power surge. The tester and meter can remain connected until other computer systems shut down, isolating the drain. As a convenience, stacking banana connectors are used on the tester. This allows voltage to be measured on various locations on the vehicle during the drain test, using standard test leads.
-
Product
Multi-Modular Cable Tester
3PK-NT005N
-
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
-
Product
LD/LED ESD Tester
-
Hanwa Electronic Ind. Co.,Ltd.
Performs automatic destructive evaluation of Lazer-Power.
-
Product
Earbud Tester
BK2132
-
When you don't need the full power of a BK2120A speaker tester, then the more portable BK2132 might be what you are looking for. This little machine is based on the more sophisticated system but it provides only basic testing. It is very fast and easy to set up and use and is especially portable as well, all for a lower price.
-
Product
Glow Plug Tester
7640
-
Peaceful Thriving Enterprise Co Ltd
The tester is able to help diagnosing the condition of glow plug without removing it from the engine. This tester is working for 12V system, tester can be energized by 12V vehicle battery directly.
-
Product
Boundry Scan Testers
-
Qmax Test Technologies Pvt. Ltd.
Boundary Scan Trainer Kit was developed by Qmax to provide user a good understanding and hands on the testing principals of boundary scan namely the scan chain test, interconnect test, non-BS functional testing of logic IC and cluster like a combinational or sequential circuits.
-
Product
Memory Module Testers
-
The module tester tests the modules in which the final tested components are assembled together. This test is also one of the most important factors to guarantee the quality of the products. DDR, DDR2, DDR3, FBDIMM,
-
Product
Sharp Edge Tester
UI-T03
-
Sharp Edge Tester is used to test if toy or other test sample has hazardous sharp edge or not.
-
Product
Transmission & Synchronization Tester
xGenius
-
xGenius is a nice handheld tester equipped with a large (8 inc) capacitive touch-screen to make easier the analysis and results interpretation. It is 100% suitable for labs or field use because is full equipped (IP/Ethernet/PTP/T1/E1), battery operated, light (1.9kg) and very rugged. The unit is able to test Ethernet/IP networks up to 10Gb/s while supporting master/slave Sync-E/PTP emulation and also has interfaces for T1/E1.
-
Product
SCSI CABLE TESTER
ST123
-
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
Product
Transformer Testers
-
*Quickly tests deenergized power distribution transformers*Briefly energizes the transformer and takes a snapshot of the condition by measuring the voltage, current and power factor of the test signal*Tests overhead, pad-mount and distribution transformers*Audible alarm confirms successful test*Improve SAIDI statistics by quickly testing and getting the transformer back in service*Auto self-test performed with every test*Compact, lightweight and easy-to-use
-
Product
Hydraulic Adhesion Testers
108
-
The Elcometer 108 Hydraulic Adhesion Tester is an extremely versatile Type III* adhesion gauge which can be used for many adhesion requirements.
-
Product
Rockwell Hardness Tester
-
The most popular and widely used method of Hardness Testing, The Qualitest range of Rockwell Hardness Tester Range start from low cost analog models up to sophisticated and advanced load-cell type models. The popular, HardRocker, QualiRock, Rocky series hardness tester models have configurations suitable for Regular and/or Superficial Rockwell Hardness Testing, while our advanced Universal Hardness Tester Range can test the full Rockwell scale in addition to Brinell & Vickers. Qualitest also offers Automatic In-line hardness testers for high volume testing.
-
Product
Battery and Capacitor Testers
-
Battery test system developed on the basis of the experience and know-how that we have amassed through implementing numerous custom-built battery evaluation systems.
-
Product
Handheld Grounding Tester
HGT1
-
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
Product
Torsion Tester
-
This apparatus is one excellent integration of measurement units. It’s mainly for the R & D department to study users’ body output in riding their designed bicycles.
