Bit Error Rate Testers
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received. Also known as: BERT
See Also: BER Testers, BERT
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Washing Fastness Tester
-
TESTEX Testing Equipment Systems Ltd.
Launderometer, to determine color fastness to washing or dry cleaning to ISO, BSI, AATCC and Marks & Spencers standards. Washing Fastness Tester complies with AATCC 61/86/132/151/190, ISO105-C01/C02/C03/C04/C06, ISO105-C07/C08/C09/D01/E03/E12, etc. Color fastness to washing is directly related to our health.
-
Product
CDM testers
Scorpion
-
Scorpion opens a new generation of CDM testers. It is designed to meet the new JS-002 standard and features Contact First pulse delivery. This patent pending technique of Contact CDM (CCDM) meets the latest CDM standards with higher accuracy for device classification.
-
Product
Alternator & Starter Testers
JBT and AST Series
-
D&V's JBT and AST line of testing units are multipurpose computerized testing systems for alternators and starters.
-
Product
Rechargeable Multifunction Tester
ET4000
-
The new ET4000 tester carries out all the tests needed to verify the safety of electrical installations in domestic, commercial and industrial wiring installations in accordance with the latest regulations.
Everything about the new ET Series has been designed to save time and make testing easier.
Fast, reliable high current and non-trip loop testing comes as standard together with a high level of input protection and a CAT IV safety rating .
Supplied with a full range of accessories.
-
Product
CELL TESTER
SPOTLIGHT
-
SpotLIGHT was designed to minimize maintenance and to significantly reduce downtime. The lifecycle of its contacting system is longer than that of standard systems currently available on the market, thus substantially reducing TCO.
-
-
Product
Silicon Heavy-doped Pen Tester
HS-MPRT
-
Heavy doped testing, especially good for purchase the material.■ Not only sound alarm, but also Led light alarm , to guarantee sorting work accurately.■ adaptable for sorting little granular material, little broken IC Wafer and other little silicon material.■ Can set alarm ranges from 0.0 to 1.0Ω﹡㎝.
-
Product
Cable Tester
-
WEETECH offers a number of individual testers for the low voltage open test and short test.
-
Product
Ground Bond Tester
264
-
Our 264 Model makes Ground Bond / High Continuity Testing simple with 40 Amps of current to satisfy your NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 264 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
Product
Analog Type Battery Tester
HH2712
-
Handy, quick and easy to use tool. For testing almost all kind batteries. Convenient Green and Red zone indication. Pocket size for easy carring and storage
-
Product
Cable Tester
CableJoG 128
-
The CableJoG 128 can test up to 128 individual connections of all manufacturers of connectors. This simple test instrument stores up to 55 separate connection configurations. Each cable that is tested is compared with the configuration stored in its memory to produce a pass/fail indication of each pin connection.
-
Product
Fiber Bundling Tester
DRK022A
-
Shandong Drick Instruments Co., Ltd.
By winding and unwinding the carbon fiber, the bundling of the carbon fiber is detected.
-
Product
Dielectric Strength Tester
HY
-
Chongqing Lushun Scientific & Technological Development Co., Ltd.
The instrument is designed and made as per the National Standard GB/T 507 "Test Methods for Breakdown Voltage of Lubricating Oil". It can be widely used to determine dielectric constant of lubricating oils in the field of railway, aviation, power plant, petroleum industry, and scientific institutes.
-
Product
Battery Tester
IT5100 Series
-
IT5100 series is a series of battery internal resistance testers with high precision, high resolution and high speed. IT5100 adopts AC 4-terminal sensing, that means the tester can test internal resistance and voltage simultaneously with high precision. Resistance resolution is down to 0.1 μΩ, voltage resolution is 10 μV.
-
Product
Flexible Leakage/Line Current Tester
RLM-10+
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
●Low-pass filter equipped, it can be cut the noise which is over 150Hz frequency.●Even Coreless Coil but Least Influence from External Magnetic Field and Residual Current●Superior Flexible CT enables Leakage Current Measurement●Backlight Function useful for measurement in the dark place
-
Product
Peel Strength Testers
-
Peel Strength Tester can be used for peeling, stripping and other performance tests of adhesives, adhesive tapes, pressure sensitive tapes, medical adhesive bandages, protection films, release paper, laminated films, leather, woven bags and paper.
-
Product
Earth Ground Tester
-
Weshine Electric Manufacturing Co., Ltd
UT520 series can perform precise 3-wire and simple 2-wire earth resistance measurement for power and electrical systems, lightning protection equipment, and ground system of all electrical equipment.
-
Product
RF PHY Tester
TLF3000
-
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - up to 40 MS/s on 8 Channels
M2P.6533-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
-
Product
PXI Programmable Resistor Module 3x24 Bit, 0 Ohm to 16M Ohm
40-295-021-3/24
Programmable Resistor Module
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
Product
Protocol Conformance Tester
TS-PCT
-
The R&S®TS PCT is a compact full range protocol conformance test solution in line with GCF and PTCRB requirements. It supports the entire device certification process for protocol testing and can be extended to operator acceptance testing by adding software.
-
Product
Coil Testers & Power Supplies
POB Series
-
Coil testers and power supply units, models POB30 and POB40 are ideal for commissioning and maintenance testing of circuit breakers. The station supply is not available. The POB series are power supply units implementing the latest power electronics technology. They are developed for use in switchyards, power and industrial environment. In addition to providing current and voltage for breaker testing, they can measure certain coil parameters.
-
Product
Continuity Testers
-
The extremely versatile continuity tester offers an insulated, shock-resistant and break-proof plastic housing. The pluggable and screwable connection between the test leads and the terminal post is safe to touch. The continuity test is indicated by an acoustical and an optical signal. The integrated torch light allows you to find wires quick and safe under though circumstances.
-
Product
Data-logging Circuit Tester for Power
-
The Log4 USB is a circuit measurement tool which both display accurate readings of voltage, current, and power while also simultaneously logging all measurement data to a MicroSD card and/or the free dedicated PC software. The Log4 USB device is specifically designed to measure the low positive voltages of USB connected equipment with high accuracy.
-
Product
Wire Damaged Tester
WDT-1
-
This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.
-
Product
Suspension/Road Contact Tester
VLT3673-G6
-
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
Product
Leeb Hardness Tester
THL210
-
LCD display of 128×64 matrix with back-light, showing all functions and parameters. Converts to all common hardness scales (HV,HB,HRC,HRB,HRA,HS). English displaying and easy and convenient menu operation. Powerful PC Software available and USB 1.0 interface and USB with Protective Membrane. 7 types of Impact Device optional, which don't need to be recalibrated when changing them. Memory of 600 groups data（impact times:32～1）. Lower limit setting and sound alarm. Material of “cast steel” is added; HB values can be read out directly when D/DC impact device is used to measure “cast steel” work piece. Printer be separated from main unit and copies of testing results can be printed as required. Normal battery AAA and big power store while USB connected and charging controlling circuit. Inbuilt function of Software Calibration.
-
Product
DMX Tester Portable
DTR-HH
-
The DTR-HH is a DMX 512 tester data send / receive unit with 10 store and recall preset scene snapshots. Each of the 10 presets will store 512 channel levels including the packet size and start code. Each preset can be edited to precise values and recalled anytime.
