Discrete Component Testers
check connected individual semiconductor components.
-
Product
Embedded Components
-
Teledyne Labtech prides itself in being at the forefront of RF/Microwave PCB development. Teledyne Labtech were also one of the first companies to successfully develop techniques for embedding SMD resistors and capacitors within multilayer structures and the embedding of connector pins in buried stripline circuits.The advantages of such a structures ensures a much higher density of interconnect. This then removes the need for via-hole connections to the board surface or the need to create access pockets to the inner layers. Consequently you finish with a board with that exhibits much lower RF/Microwave losses. This is particularly important when designing large RF feed networks or 16:1 power dividers.
-
Product
RF-MW-MMW Components
-
Our high-performance board-level components incorporates advanced resistive and signal distribution technologies for a broad range of frequency spectrum applications. Our extensive portfolio of RF devices is used to attenuate, level, or terminate signals available in a variety of packages and footprints for demanding high reliability environments.
-
Product
IPD RF Components – LTCC
-
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
Product
Electronic Component Counter
ZE 300
-
REINHARDT System- und Messelectronic GmbH
Instead of the widely used photoelectric barrier technology a new measuring technology is used in the new electronic component counter ZE 300: The laser technology offers a measuring beam with higher energy density and therefore more precise counting and faster counting speed. The ZE 300 component counter is microprocessor-controlled.
-
Product
32-CH Discrete Output Daughter Board Module
HSL-DO32-DB-N
-
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type outputs*Photo couple isolation voltage: 2500Vrms*Output switching capacity: Single channel 500mA; all channels 60mA at 24VDC*Output response time:ON OFF: 180µs, OFF ON: *1.2µsTerminal Base:HSL-TB64 or HSL-TB32U-DIN
-
Product
Broadcast Components
-
Cable testing sections may be used to isolate the antenna inputs from the main feeder when testing either the antenna or feeder. These devices are normally installed between the main feeder cable and antenna inputconnector and allow access to the antenna input without the need to remove the main feeder cable. Cable test sections are particularly useful with large feeder cables that are difficult to manoeuvre.
-
Product
LCR Meters and Component Analyzers
6500P Series
-
Accuracy and versatility makes these HF LCR Meters the idealchoice for many different tasks and applications in the area ofmanufacturing test. The wide range of frequency specificationsmeans that a customer can select the model which best meetstheir requirements and budget.
-
Product
Oil Testers
-
PeakTech Prüf- und Messtechnik GmbH
This device was developed for the quick and reliable testing of frying oils in the catering trade, commercial kitchens and also for private users. With the device settings it is possible to display the oil temperature of the deep fryer. By measuring the TPM value (Total Polar Materials) the content of polar substances can be determined, which is a reliable parameter to characterize the extent of aging of the frying oil / frying fat during frying.
-
Product
Discrete Switch Cards
-
Compatible for use on the VXI, LXI, and GPIB platforms, these switch products were formerly sold under the Racal Instruments brand name.
-
Product
Continuity Testers
-
Triplett Test Equipment & Tools
Tester performs a TIA568 test on CAT5/6 network cable (RJ45) with instant PASS/FAIL results — opens/shorts, reversals, split pairs, and continuity. It is ruggedized and cushioned for toolbox use with a hidden drawer for remote storage. Includes a built-in tone generator for tracing and troubleshooting.
-
Product
Electrical Tester
PRO T6-1000
-
The T6-1000 PRO Electrical Tester measures voltage up to 1000 V ac and current up to 200 A ac, all through the open fork and without test lead contact to live voltage. Connect the black lead to ground with the included heavy-duty alligator clip, slide the wire into the open fork and see both voltage and current at the same time. On wires up to AWG 4/0 (120 mm2), carrying as much as 200 A and 1000 V ac. Even with gloves on. It will change how you do your job.
-
Product
Scratch Tester
-
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
Product
24 Ch , Discrete I/O (0 to 60 VDC, 500 mA/Ch.)
DT1
-
The DT1 module features 24 programmable channels for either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3 – 60 VCC source. These modules can sense broken input connections and whether an input is shorted to +VCC or to ground.
-
Product
Display Tester
-
Yuyao City Yinte Neon-Electroscope Factory
This neon-electroscope is applicable for directly detection of 12-240V zero line indirect detection of DC.
-
Product
Installation Tester
M72
-
Multifunction installation tester for insulation measurement up to 500V, continuity of protective conductors, phase sequence with TRMS multimeter functions.
-
Product
Roughness Testers
-
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
Product
Cable Testers
E448
-
The EMO cable testers are designed for use in portable and bench mounted applications, including the assembly and testing of cables.
-
Product
Alternator Tester
QME-2D
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to fast test generator performance. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing generator (test items difference appear in the different types motor)Test standard.
-
Product
Tester For Maintenance
-
Mobile wiring testers in Multibox design or in customer specific housing for maintenance on military vehicles.
-
Product
PRECISION COMPONENT ANALYZER
6400 SERIES
-
The 6430B and 6440B Precision Component Analyzers provide thorough and accurate testing of any passive component to high resolution. In particular, for capacitor manufacturers, the instruments provide capabilities for both fast automatic production testing and complete design characterisation. Users include designers of passive components, manufacturing test, designing and testing materials as well as circuit designers who are evaluating component characteristics.
-
Product
Continuity Tester
26200
-
Just clip lead to one end of wire in question. Probe other end of wire. If bulb lights up, there is continuity. If bulb fails to light the circuit is open. Not to be used on live circuits or computer sensor feed circuits.
-
-
Product
Trailer Tester
Inspector 930
-
The Inspector 930 trailer tester is a complete, all-in-one trailer diagnostic system which simplifies ABS, brakes, air, lights, and electrical testing. It provides the ability for a single technician to perform a full inspection in one trip around the trailer.
-
Product
Test Connector Components
-
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
-
Product
Downproof Tester
TF134
-
TESTEX Testing Equipment Systems Ltd.
Take an agreed size specimen from the fabric to be tested to sew a pocket at specified size , fill with a certain Weight of down, feathers or a mixture of both, then sew the fabric up to be a testing bag. Clamp the both sides of the bag in the holder. After test to determine the downproof ability of the fabric by calculating the number of down and feathers through the fabric
-
Product
Sensor Tester
QST-5
-
The QST-5 device is intended for testing many popular sensors used in the automotive industry. The tester powers the tested sensors by itself, so it can be used both in a vehicle and outside of it.
-
Product
Battery Tester
B1706
-
ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.
*No test leads needed*Easy-to-read color scale*Self powered-no need of battery *1.5V=AAA,HP16,MN2400,RO3 AA,HP7,MN1500,UM3 C,HP11,MN1400,SP11,LR14,LM2 D,HP2,MN1300,SP2R20,UM1
-
Product
Ferroelectric Tester
Premier II
-
The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.
-
Product
Modbus Master TCP/IP Component for .NET
WSMBT
-
WSMBT is a powerful and simple to use .Net component that makes it easy to access data from a Modbus slave device connected to the PC's Ethernet network. Simply drop the component on your form and talk to your device with your VB.NET, C# or Managed C++.
