Distributed Antenna System
-
Product
Hall Effect Measurement system
HMS-5500
-
Variable temp : 80K ~ 350K (model# : AMP55T ) - HMS-5500 can be compatibly used with both low temp magnet kit (model# :AMP55T) and high temp magnet kit (model#: AHT55T5, upto 500dC) - Below image is to show model# HMS-5500 + AMP55T, for low temp.
-
Product
Massively Parallel Board Test System
I7090
In-Circuit Test System
The Keysight i7090 is a massively parallel board test system designed to help PCBA test engineers improve manufacturing efficiency while reducing costs. Unlike traditional in-circuit testers, the i7090 supports up to 20 In-Circuit Test cores in parallel, which means engineers can test multiple Units Under Test (UUTs) simultaneously without the need for multiple systems. This reduces scaling and infrastructure costs and frees up valuable testing space.
-
Product
High Gain Horn Antenna
BBHA 9120 K
-
The BBHA 9120 K is a linear polarized high gain horn antenna for immunity testing at short distances, especially optimized forAutomotive 600 V/m Pulse Radar Test 1.2 - 1.4 GHz. Standard: General Motors: GMW3097, Ford: EMC-CS-2009.
-
-
Product
Active biconical Antennas
BicoLOG X Series
-
Only a single broadband test antenna for the complete frequency range from 20MHz up to 3GHz. Optimal for usage with spectrum analysers for EMC measurement. Active Antennas with high gain up to 41dBi.
-
Product
Test Tables / System Solutions
-
WEETECH, as a manufacturer of test equipment, offers its customers also a "Ready To Use" test system solution. It consists of the test table, the customer-specific adaptation as well as the test device, and is very quickly ready for use at the customer's site. According to the customer's requirements, the set-up is designed as a system with permanently installed adaptations for the production of constant cable harnesses in large quantities or with interchangeable adapters for the flexible production of different cable harnesses. Depending on the application, a larger table version or a smaller desk version is available. Various interfaces are available for integrating these solutions into a complete production automation system.
-
Product
Display Measurement Systems
DTS Series
-
Instrument Systems Optische Messtechnik GmbH
Characterization of emissive, transmissive, reflective, and transflective displaysViewing-angle-dependent analysis of illuminance, contrast, color, and derived parametersDetermination of the electro-optical transfer function: analysis of luminance, contrast, and color depending on electrical driving conditionsMeasurement of transient properties, such as switching times, flicker, and modulation
-
Product
Mobile Gas Leak Detection System
ABB Ability
-
ABB Ability mobile gas leak detection system uses ABB’s patented Off-Axis Integrated Cavity Output Spectroscopy (OA-ICOS) technique which has a sensitivity and precision more than 3000 times greater than legacy methods. This enables identification of leaks several hundred feet away from the source. Current traditional leak detection technology is slow, laborious and costly. Operators walk on foot near the pipeline with hand-held sensors making paper-based reports.This is slow and can lead to dangerous leaks being missed or not identified in a timely manner. ABB’s Ability mobile gas leak detection system delivers a low cost per leak solution with low false positives. Reporting includes mapping of the leaks available via a mobile app and measurements as Cloud-based service. The system consists of ABB’s Methane/Ethane Analyzer, a GPS, a sonic anemometer and proprietary leak detection software that presents real-time geospatial maps of multiple gas concentrations in real time. The software’s sophisticated leak detection algorithm combines the system’s measurements of gas concentrations (CH4, C2H6), local coordinates (GPS) and local wind velocity (sonic anemometer) to estimate the location of the leak. Readings are stored in the device and can be transmitted in real-time to the cloud for centralized monitoring.
-
Product
Steering Module Test Systems
-
Steering test systems for quiet evaluation of rattle, NVH & performance issues – non-hydraulic. The MB Dynamics Steering Module Test Simulator family of technologies (SMTS) is an assembly of components and software designed to facilitate the quiet testing, development, troubleshooting, and auditing of a variety of steering gear and steering column assemblies — collectively referred to here as steering modules (including components).
-
Product
SAP Continuous Delivery System
ActiveControl
-
ActiveControl allows SAP systems to respond to new business requirements at high speed. Its range of powerful automation features support agile development, DevOps and Continuous Delivery in SAP environments, generating more business value through faster, safer application delivery. ActiveControl consists of four component modules that combine to accelerate change without putting business continuity at risk.
-
Product
Full Wafer Contact Test System
Fox 1
-
Unique cartridge technology uses full-wafer contactors combined with parallel test electronics to achieve single touch, full-wafer test
-
Product
Vision Inspection Systems
-
We have available with us diverse array of Vision System. These systems are based on high-end technologies and meet the requirements of diverse sectors. Further, our systems are an epitome of quality and available at economical prices. Details of different systems.
-
Product
VECTOR-GUN HANDHELD DIRECTION FINDING ANTENNA SYSTEM
HFDF
-
National RF's Type HFDF active directional antenna system consists of a high gain RF amplifier coupled to a tunable Faraday shielded loop antenna. Several loop antenna assemblies are available to provide coverage of frequencies in the HF and low VHF spectrum. Due to the nature of a Faraday shielded loop, the antenna exhibits a sharp null through the diametric center of the loop. This null is used to determine the direction of incoming radio signals or to locate electrical noise being radiated from some source. The internal high gain amplifier is used to compensate for the inherent inefficiency of the actual loop at the operating frequency. Overall, the system dynamic response is about +6 dB as compared to the dynamic response of a dipole. To aid in the direction finding process on strong signals, an internal 30 DB attenuator is provided. As the loop antenna presents a bi-directional response, tri-angulation may be required to eliminate the ambiguous signal direction. The line of site of the incoming signal is determined by listening for a signal null on the receiver or by watching the receiver’s S-meter.
-
Product
Automated Soil CO2 Flux System
LI-8100A
-
A portable, automated system for simple and reliable survey and long-term measurements over a study site. The LI-8100A Analyzer Control Unit contains an infrared gas analyzer and a connection panel to interface with the 8100-103 Survey Chamber, the 8100-104 and 8100-104C Long-Term Chambers, additional gas analyzers, and the LI-8150 Multiplexer.
-
Product
Hardware Security For Programmable System Control
Mach-NX
-
*Up to 8.4K LC of user logic, 2669 kbits of user flash memory and dual boot flash feature*Up to 379 programmable I/O supporting 1.2/1.5/1.8/2.5/3.3 I/O voltages*Secure enclave supports 384-bit cryptography, including SHA, HMAC, and ECC*Configuration of PFR and security functions through Lattice Propel simplifies developer experience*Highly reliable. Low power and 3X better SER performance to comparable CMOS technologies
-
Product
Touch Posi-Control System V2
DPC
-
The position control torque arm system helps manufacturers detect and eliminate costly screw-fastening errors during the assembly process. This position control system is designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. A good tightening sequence ensures that an even preload distribution is achieved in the joint. Using a position control system is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.
-
Product
Custom Systems
-
No two products or processing challenges are exactly alike. That’s why a specially-configured MAC® Custom System can help you address unique testing requirements…as well as the demands of your own internal standards
-
Product
X-ray Inspection System
TruView Prime
-
The TruView Prime is a fully motorized radiography system developed to meet the stringent requirements of electronics assembly and component inspection. The TruView Prime is professionaly built - something hard to find in entry level systems in the TruView Prime's price range.
-
Product
Polarity & Burn in Test Systems
-
Our polarity and burn-in test systems are available for components such as multilayer, disc type or hollow ceramics.
-
Product
Mass Flow Test Systems
-
No matter the industry, product integrity is necessary to the manufacturing process. Everything leaks, and mass flow testing provides a fast, reliable determination of leakage to ensure it is within permissible ranges.
-
Product
Portable Metal Detection System
XT 8000
-
The new XT 8000 portable walk through metal detection system is a full featured digitally controlled unit that can be deployed in less than five minutes, yet stores away in a rugged carry bag for easy transport. Only $3,995.00 eachBuy NowOur Price $3,995.00 The new XT 8000 portable walk through metal detection system is a full featured digitally controlled unit that can be deployed in less than five minutes, yet stores away in a rugged carry bag for easy transport.XT 8000 is simple to set up and operate without specialized training. The system can be moved regularly to different facilities to provide security and deterrence while costing thousands less than permanently installing units at each site.
-
Product
Cable Diagnosis System
Baseline 9400 TDR/ICE
-
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
Product
Internal Antennas
-
Pulse offers a large selection of internal antennas that are designed into an incredibly diverse selection of solutions, from smart home IoT devices to utility meters, from point of sale products to wireless charging. The PCB antennas, including those made with flexible material, are made to be mounted or adhered against a plastic surface and connect via cable to your PCB, and cover the ISM, WiFi, GNSS, and cellular bands. The NFC selection for 13.56 MHz will work with both 50 and 80 Ohm radios and include antennas with a ferrite backing to work even when mounted against metal. The selection of active GNSS patch antennas with cable are perfect for ensuring your device’s whereabouts are accurately tracked. Finally, the many transmit and receive coils for wireless power charging will add this popular consumer capability to your product, cutting one final cable from design. Use the product finder below to find the perfect internal antenna solution for you.
-
Product
Bolometer Systems
-
The detector comes with an IR light collecting cone assembly, vacuum-sealed wedged window, field of view baffling, and low noise electronics. The bolometer system is then outfitted with a single cut-on IR filter or a cold, manually operated, 2 or 3 position filter wheel. We offer a selection of far IR cut-on long pass filters that range from 10 to 285µm.
-
Product
Obsolete ATE, Replacement Systems
-
No one likes saying goodbye to a faithful old friend but now that the economy is on the up, has the time finally come to replace your ageing Automatic Test Equipment (ATE) or Special to Type test system?
-
Product
Vacuum Handling Systems
-
RECIF Technologies history started in 1982 offering its first wafer handling solution: Vacuum handling Systems.Based on this historical technical mastery, Recif Technologies provides today a full range of single wafer manual vacuum handling solutions adapted to our customers’ and current Semiconductor industry’s’ requirements.
-
Product
X-ray Fluorescence Measuring System
FISCHERSCOPE X-RAY/XDV-SDD
-
Premium model for universal use for the inspection of very thin or complex layers up to RoHS screening at very low detection limits.
-
Product
Tire Rolling Resistance Test System
-
This system measures the rolling resistance of each tire accurately. In addition to the simultaneous measurement of tire loss resistance and rolling resistance coefficient for each drive by mode operation (JC08, WLTC), coasting test, constant acceleration/deceleration test and transient mode test are able to be performed. Furthermore, measurement of driving noise/ vibration of the tire, effect of the tire loss due to the temperature change can be verified by adding options.Conforming the JIS D 4234: 2009 and ISO 28580: 2009.
-
Product
Neutron Flux Monitoring Systems
-
To monitor reactor core neutron flux and provide indication during all modes of reactor operation, and to provide trip signals to the Reactor Protection System (RPS) and the Reactor Manual Control System (RMCS).
-
Product
GPS/GNSS Antenna Signal Splitter 3-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS321
-
INSTOCK Wireless Components, Inc
GPS321 is a three way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
