-
Product
High Voltage Insulation Tester Module
DP-cPCI-5586
-
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
Product
Wide Range Flexible Current Probe
EFX6000
-
The EFX6000 is a flexible AC current clamp utilizing the Rogowski principle. It can be used to measure currents from 1 amp to 6000 Amps in 2 auto-ranges, over a wide frequency range to 10kHz. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas, around large conductors and where access to confined or tight spaces is a problem. It requires no batteries or external power supply.
-
Product
Desktop MW Signal Generators
-
The Desktop platform offers all the functionality of a fully featured full-size MW analog signal generator in the smallest footprint module available on the market. Its small size enables using it as a desktop unit or easily scaling up to hundreds of channels, while keeping the required space to a minimum, let it be 20 GHz or 40GHz, excellent signal quality and integrity and fast switching speeds.
-
Product
Wavelength Selective Switches
WSS
-
Use our modules for wavelength routing to combine, manipulate, or separate multiple WDM and DWDM signals from 100 GHz spacing down to < 25 GHz, all with no crosstalk.
-
Product
Ultrastable Microwaves
-
Ultra-stable microwave sources are paramount for a broad range of applications, including precision metrology, deep space navigation, telecom and next generation wireless communication, as well as coherent radar. With the PMWG-1500 Menlo Systems offers a unique commercial solution for providing ultrastable microwaves in an all-in-one solution.
-
Product
Intelligent Interface Card
IIB-1553-PC104
-
The IIB-1553-PC104 is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-PC104 supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a single, dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable. The board is supplied with C drivers in source code and Windows menu driven software as standard
-
Product
SparkFun GPS Breakout
Chip Antenna, SAM-M8Q (Qwiic)
-
The SparkFun SAM-M8Q GPS Breakout is a high quality GPS board with equally impressive configuration options. The SAM-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
200MS/s Four-Channel Arbitrary Waveform Generator
WW2074
Waveform Generator
The WW2074 offer a 200 MS/s four-channel universal waveform synthesizer. Each is built in a small case size to save space and cost but without compromising bandwidth and signal integrity. The instrument outputs either standard or user-defined waveforms in the range of 100µHz and up to 80MHz.
-
Product
6TL36 Plus In-line Test Handler w/Bypass
EA923
-
- Test handler 6TL36 Plus.- Dual line (bypass)- 1096 x 1875 x 1851mm [WxDxH]- Expandable to form a group with several 6TL36 modules (adapt line to production volumes).- ICT, FCT with RF, ISP or Combined test (ICT+FCT)- Servocontrolled DUT stop (stopper-less system)- Exchange time 3,2s- Max. PCB dimension 600x450mm- 19” rack space for instruments integration: 28UH- Receiver 25 slots in probe plate + 4 slots in push plate- Automatic Conveyor width adjustment- Optional Return Conveyor- High dynamics conveyors (1500 mm/s)- 90mm Top-30mm Bottom Component clearance- SMEMA and Hermes standard- CE
-
Product
Printed Circuit Board
RISER-PPM-1
Printed Circuit Board
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
-
Product
Zinc Diecast Body Vacuum Switch
P119V
-
The P119V Zinc Diecast Body Vacuum Switches are the inexpensive version of the P117V and recommended for indoor OEM use. It is commonly used in the medical field and as a safety switch in numerous applications. The compact nature of these switches make them ideal for tight spaces.
-
Product
Six-Cell Diffusion Testing System
Phoenix DB-6
-
The Phoenix DB-6 (six-cell diffusion block) provides an ideal platform compliant with 21 CFR Part 11 for release-rate testing of six vertical diffusion cells at once using manual sampling methods. Controlled by an advanced computerized display, the DB-6 provides uniform and precise heating and stirring of six cells. The compact footprint of the DB-6 economizes on lab bench space.
-
Product
2-in-1 High-Voltage Test Hood
LX-HVE900EC
-
The test cells are made of stable, highly insulating plastic and are closed by a swiveling, transparent cover. The built-in safety switch is used to lock the hood and release the high-voltage sources. This ensures that no high voltage is active when the door is open. There is a generously dimensioned wiring space in the floor of the test cage. An interchangeable adapter plate in the test cell - optionally with an interchangeable interface or an interchangeable adapter cassette - allows quick adaptation to different types of test items. Prepared openings enable connectors and other common interfaces or cable bushings to be easily attached. The hood is opened and closed almost effortlessly thanks to precisely coordinated gas springs.
-
Product
Easycheck Fiber Endface Inspector
CA3002
-
The integrated style design makes the size compact and operation easy. You are no longer to worry about so many cables between monitor and microscope, greatly saving the time for operation and worktable space, thus creating more productivity. Easycheck have a series different model according to different application, it has photo capture function; for transceiver checking; X、Y adjustable; image auto analysis and judgement, etc. The user can choose the desired model per the requirement.
-
Product
LXI Microwave Multiplexer, 50Ω 36-Channel 1-Bank 4GHz BNC
60-891-001-002
Multiplexer Module
The multiplexer has an extremely high level of performance with low VSWR, very high isolation, low loss and high power handling. It is ideal for switching 50Ω systems for HF up to microwave frequencies. It occupies 2U of rack space, providing a compact switching solution.
-
Product
Combined Environmental Reliability Test System
VTC SERIES
-
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
Product
Preselectors and Switch Filter Banks
-
Our preselectors and switch filter banks offer low noise figure, high dynamic range, state-of-the-art filter rejection with high channel-to-channel isolation front ends, realized in compact building blocks, designed in custom form factors. Applicable markets include: EW, missiles, radar, communications and space.
-
Product
Vision Standard IP Cores
-
S2I’s Vision Standard IP Cores solutions are delivered as a working reference design along with FPGA IP cores. This minimizes development time and allows for top-notch performance at a small footprint, while leaving enough flexibility to customize the design. Sensor to Image cores are compact and leave enough space in the FPGA for your application.
-
Product
Digital Mission Engineering
-
From chip to mission, connect modeling and simulation efforts across all phases of the engineering product life cycle. Model multi-domain operational environments, including land, sea, air and space, with accurate, dynamic, physics-based simulations. Integrate with the Ansys portfolio of multi-physics tools and solvers to achieve unmatched end-to-end modeling and simulation.
-
Product
Digital Storage Oscilloscopes
SDS1000DL+ Series
-
The SIGLENT SDS1000DL+ series is a dual-channel 50 MHz model. It includes a 30 kpts memory depth that helps to ensure accurate waveform resolution and to capture long signal lengths. With its 7-inch TFT-LCD (800*480) screen, there is adequate screen space to help better see and analyze waveform details. Along with a 500 MSa/s sampling rate, the SDS1000DL+ supports 32 parameters measurements and common mathematical operations to speed up complex / repetitive measurements.
-
Product
Backplane Connectors
-
Offering a broad portfolio of backplane connectors that include SOSA aligned optical, COTS plus hard metric, VITA standard and high speed twinax interconnects. Our interconnect solutions address the requirements of mission-critical applications within commercial aerospace, space and defense market segments.
-
Product
4 MP OV4682 RGB IR Camera Module
e-CAM40_CUMI4682_MOD
-
The e-CAM40_CUMI4682_MOD is a 4 MP RAW RGB-IR MIPI OV4682 camera module with the M12 S-mount lens holder. The e-CAM40_CUMI4682_MOD RGB IR camera module is based on OmniVision's OV4682 1/3" Optical format CMOS Image sensor, that captures high-resolution images and videos as well as IR information. Its dual RGB-IR Camera capabilities allow it to bring a host of additional features to machine vision applications and by combining RGB - IR in a single camera module reduces the total cost and saves space. Customers can evaluate e-CAM40_CUMI4682_MOD with See3CAM_CU40 over USB 3.0 interface and e-CAM40_CUTK1 over MIPI interface. e-CAM40_CUMI4682_MOD camera module can stream the 4MP(2688x1520) unprocessed 10-bit RAW data video upto 40 fps.
-
Product
14-Slot Combination PXI Chassis
GX7100 Series
Chassis
The GX7100B Series are 14-slot combination PXI chassis that accommodate 3U and 6U PXI controllers and instruments in 4U of rack space. The GX7100B’s unique format includes seven 3U-only slots and seven 3U/6U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI applications and requirements.
-
Product
Colorimeters
-
A colorimeter is a valuable color-measuring tool used by manufacturers, printers, painters, designers and quality control professionals. Colorimeters ensure accurate, consistent color, eliminating issues related to color subjectivity. Depending on the model, PCE Instruments' colorimeter products can measure colors in different color spaces such as CIE LAB, XYZ, LCh, RGB and LUV (for liquids and solids / that is why you can choose the media via filter selection). The most popular colorimeter models in our range of color-reading products are the PCE-CSM series colorimeters. Aside from being easy to use and economical, the PCE-CSM series colorimeters offer high degrees of accuracy.
-
Product
Fibretool Portable Fiber Optic Inspector - HW-700V
-
Shanghai Fibretool Technology Co.,Ltd.
● 2.7 inch handheld DM27 monitor;Brightness and contrast adjustment● Quick navigation, get image within 3-5 seconds; Two-way focus control● 95% Image centralization, Clear image, no interface, no flash● 27 types of adapters tips available to inspect different connectors and angle-mounted connectors with limited access space● Precise resolution (<1 um), no shadow or vignetting in screen● Reliable output signal, no default under repeated operation● Various monitors can be chosen with specific display capability
-
Product
Programmable Multifunction Counter Board, Isolated, w/ 4 Function Modules & BISS-Master Logic
CPCI-1710-10K20
-
The board CPCI-1710 is a fast multifunction and multichannel counter board for the CompactPCI bus. The strengths of this board are its wide range of applications and high precision and reliability for though industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provides the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied sofware. The flexible programming facilities on this board allow many different user applications to be quickly and easily developed or reconfigured as further requirements arise.
-
Product
Sensors
-
A speed and angle sensor using a black/white tape which is glued on a rotating part. The reflection is converted into a TTL signal, bandwidth 100 kHz. The sensor consists of a tiny electronics part and a 5 m fiber optic cable terminated with a M6 screw. Thus areas where space is very limited still can be reached conveniently.
-
Product
Desktop AC Power Supply
DRJ Series
-
DRJ Series is a stable sine wave output AC power supply of the world's smallest class that integrates the functions of rack-mount multifunctional AC power supply DRA Series in a desktop size. It is a new type of AC power supply that addresses both space saving and high-quality output that are required in experiments, evaluation tests, production line and so forth. With worldwide input feature DRJ can be used anywhere in the world. In addition, it delivers simple operability in a compact size, allowing first timers to operate easily.
-
Product
Break-Over Wrenches
TBIH
-
The TBIH is a small torque wrench ideal for applications with limited space. The flexible preset wrench can adapt to different fastening applications as it is compatible with different head options like open end, box end, flare end, hex key end or a ratchet head. The slim wrench features a tamper-proof internal adjustment. When the TBIH torque wrench achieves torque, the head breaks-over signaling to the operator to stop applying torque to the fastener or bolt. Break-over torque wrenches improve control of the fastening process by reducing the risk of both over and under tightening.
-
Product
Field Test Kit
621
-
TESCO’s light-weight, 50 Amp Field Meter Test Kit (Catalog No. 621) with Power Factor, has been designed to reduce the weight of field test equipment to the lowest possible limit. The carrying case is fabricated from durable powder coated aluminum. The total weight of the meter test kit including leads, and digital reference standard is only 25 lbs! The test kit also incorporates ample storage space for the cable set.
