-
Product
Complete IP Module
Scan Ring Linker SRL
-
The Scan Ring Linker SRLTM - is a complete IP module that can be easily embedded into a CPLD, FPGA or ASIC on a PCB to reduce the complexities and costs of designing 1149.1 (JTAG) test infrastructure for designs that use multiple scan rings. The SRL IP module links any number of scan rings (secondary scan paths) into a single high-speed test bus, which permits devices on secondary scan chains to be independently tested and configured through a single 1149.1 external interface.
-
Product
PCI High Density Potentiometer Card 5-Channel, 8-Bit, 0 To 255 Ohm
50-296A-021-5/8
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Resistor Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-295A-021-3/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Tactical Grade Inertial Measurement Unit (IMU)
ADIS16490 iSensor
-
The ADIS16490 iSensor® device is a complete inertial system that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16490 combines industry-leading iMEMS® technology with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, and linear acceleration (gyroscope bias). As a result, each sensor has its own dynamic compensation formulas that provide accurate sensor measurements. The ADIS16490 provides a simple, cost-effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The SPI and register structure provide a simple interface for data collection and configuration control.
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Tunable Notch Filters
-
The Ranatec Tunable Notch Filters are critical tools for adaptation to stringent new ETSI/3GPP conformance test specifications for mobile device radio properties, that covers all sub-6 mobile bands and channel bandwidths for 2G/3G/4G/5G. Designed for formal conformance testing performed by accredited test houses, as well internal verification by mobile device vendors. A flexible and easy to use test automation platform to support almost any ambition level, tailored to your demands.
-
Product
Abrasion and Washability Tester
1720
-
The Elcometer 1720 Abrasion and Washability Tester is robust, reliable and extremely versatile and is designed for testing the washability, brushability and resistance of a wide range of materials.
-
Product
PXI Resistor Module 4-Channel 1R to 127R
40-293-012
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable DC Electronic Load
IT8500+ Series
-
IT8500+series (150W~3000W) single-channel programmable DC electronic loads are designed for middle & high-end applications. They can be offered as multiple solutions according to customer's design and testing requirements.
-
Product
Test Solutions For MROs
-
Through our 50+ years of experience, we’ve designed equipment that test components on nearly all aircraft platforms. Because of our experience and our attention to industry trends, we can anticipate what components you’ll be testing tomorrow. We design our test stands to exceed your current test requirements for simple upgradability to ensure that you’re ready for the future.
-
Product
Advanced Power System - Dynamic DC Power Supply, 9 V, 100 A, 1000 W
N7950A
DC Power Supply
The N7900 Series dynamic DC power supplies are designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
Multifunction Substation Test Set
STS 4000
-
STS 4000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers, designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm - SPST
40-294-113
Programmable Resistor Module
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Long Gauge Length Axial Extensometers
Model 3542L
-
Jinan Testing Equipment IE Corporation
The dual flexure design makes the 3542L very rugged and insensitive to vibrations. These extensometers are designed for testing a wide range of materials including metals, plastics, composites and ceramics. Epsilon’s Model 3543 is recommended for applications requiring long gauge lengths and larger measuring ranges.The Model 3542L comes standard with Epsilon’s quick attach kit, making it easy to mount the extensometer on the test specimen. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The 3542L extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Test Pattern Generator Software
ScanExpress TPG
-
To deliver a product meeting the highest standards of quality and reliability, design engineers and test engineers alike must maintain test capabilities throughout the entire product life cycle, from prototype to manufacturing. Automation in test generation is essential to ensure that tests keep up with the rapid development of modern products.The ScanExpress TPG™ Intelligent Test Pattern Generator Software provides a highly advanced, automated boundary-scan test design environment—perfect for quick and efficient creation of complete boundary-scan tests for all IEEE-1149.1 and IEEE-1149.6 compliant circuit boards.
-
Product
Variable Resistor Load Bank
REOLOAD 100
-
A variable resistor load-bank with fixed stages connected in parallel and switched in, as required, with an adjustable stage for fine trimming. Designed for testing equipment under load. 1000V (AC or DC). 250A and 2500
-
Product
Advanced Power System - DC Power Supply, 40 V, 50 A, 2000 W
N6972A
DC Power Supply
The N6972A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
High Voltage Tester
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI make high voltage tester is specially designed to test induction & submersible motors with cutting edge technology.High Voltage Tester is manufactured as per the International set standards and regulations. This High Voltage Testers are available in AC and DC types and are used for testing HV cables after installation and repair for ensuring efficient performance. It also indicates voltage withstands level and current leakage level of the cable during the testing period.
-
Product
PXI Programmable Power Supply
Programmable Power Supply
PXI Programmable Power Supply modules feature multiplechannels that you can combine for higher voltage or current capabilities. Some modules include isolatedchannels and an output disconnect functionality that allows isolation from the device under test(DUT) when not in use and remote sense to correct for losses in system wiring. You can use these models to simplify the task of designing automated test systems for a wide range of applicationsfrom aerospace and defense to automotive and component testby eliminating the need to mix multiple instrumentation form factors in a given test system.
-
Product
Automated Discrete Semiconductor Tester (ATE)
5300HX
-
The Model 5300HX Automated Discrete Semiconductor Tester (ATE) is designed for fast, reliable testing of a wide range of discrete devices. Using an on-board Intel SBC, can provide stand alone testing capability or connected to a PC for intuitive test development and data capture.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
Shielding Solutions
-
Antenna Test Chambers are especially designed for testing RF devices and antennas from frequency ranges of 700 MHz to 6000 MHz. These Antenna Test Chambers provide a shielding of more than 90 dB as well as lowest residual passive intermodulation.
-
Product
SAS
-
SCHILLER AUTOMATION GmbH & Co. KG
The Gen4 Mini-SAS HD adapter kit will facilitate compliance testing for SAS-4 host, device, and cable. The left and right-hand version plug adapters are designed to test side-by-side.
-
Product
High Quality Transformer Oil Dielectric Strength Tester
AS-023A
-
Chongqing Assen Power Equipment Co., Ltd
AS-023A Series High Quality Intelligent Transformer Oil Dielectric Strength Tester is specially designed for testing dielectric strength (Breakdown Voltage) of transformer oil. The breakdown voltage (dielectric strength) is one of the most important parameters of transformer oil, it is a rule of the voltage withstand. The value of breakdown voltage (dielectric strength) indicates whether the oil contains water, impurity and electric particles, and you’ll know the oil value via the breakdown voltage (dielectric strength).
-
Product
Programmable S/R Standard & Simulator
5300
Simulator
NAI’s 5300 Synchro/Resolver Standard & Simulator is a laboratory-grade, programmable instrument. This model can be used as a true Synchro/Resolver standard for calibrating and testing Automatic Test Equipment (ATE) for Calibration/Metrology Labs, and for Engineering Design and Production Test environments. It can also be used to measure Angle Position Indicators (API) and Synchro-to-Digital converters for static or dynamic characteristics. This model also may use an external reference waveform.
-
Product
RF Shielded Test Enclosure, Large, Yet Benchtop Enclosure
JRE 2525
-
Originally designed for testing rack mounted RF Sensing equipment, the roomy JRE 2525 is ideal for large wireless devices such as; Rack Mount Mesh Network AP's, Cellular/LTE/4G Base Stations, Wireless Laptops, Test Fixtures for testing Large RF Modules, and other large RF devices.
-
Product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Advanced Power System - DC Power Supply, 120 V, 16.7 A, 2000 W
N6976A
DC Power Supply
The N6976A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
Transformer Turns Ratio Meter
TTRM 302
-
SCOPE introduces state of the art precision three phase Transformer Turns Ratio Meter (TTRM ) designed for field testing as well as factory testing of power transformers, instrument transformers and distribution transformers of all types. Along with turns ratio, this light weight and reliable instrument measures ratio deviation, phase angle deviation, magnetizing current and detects tap-position of single as well as three phase transformers in charged switchyard condition. The instrument has facility to automatically detect vector group of all majority configurations available. The differant AC voltage selection offers high accuracy in measurement.
-
Product
Low Loss Cable Assemblies
True Blue
-
The Answer: An unmatched combination of low loss, durability, and value.The Question: What does Teledyne Storm Microwave’s True Blue® line of cable assemblies provide?For more than 30 years, our True Blue® assemblies have been the winning choice of design, test, and production engineers for:- Military and aerospace design-in applications- General purpose test applications- Production testing- With a design based entirely on high-performance materials, the True Blue® line covers frequencies from DC to 50 GHz.Assemblies are available in both custom configurations and a variety of standard lengths and connector combinations.The basic True Blue® cable is designed to be durable. However, for applications requiring added durability, assemblies are also available ruggedized, armored, and soft armored.
