Shielded Cabinets
A space surrounded by an electromagnetic radiation barrier
See Also: Faraday Cages, RF Enclosures, Shielded Box, Shielded Enclosures
-
Product
Shield Box
-
Anritsu's Service Testers and accessories enable OEM aftermarket service and authorized repair centers to troubleshoot and repair mobile phones and data devices quickly and economically. A full range of accessories are available including shield boxes and automation software to provide scalable test capability to the industry.
-
Product
Arduino CAN Shield
IFB-10003-ANP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
SCB-19 Noise Rejecting, Shielded Aux I/O Connector Block For FlexRIO
782444-01
-
Screw Terminal, 19-Pin HDMI, Noise Rejecting, Shielded AUX I/O Connector Block.
-
Product
SH37F-37M-2 37-Pin Female to Male Shielded I/O Cable, 2 m
778621-02
-
SH37F-37M-2 37-Pin Female to Male Shielded I/O Cable, 2 m
-
Product
SH25F-25M-1 25-Pin Female to Male Shielded I/O Cable, 1 m
192568-01
-
SH25F-25M-1 25-Pin Female to Male Shielded I/O Cable, 1 m
-
Product
SH96F-96M-5, Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 3 Meter
786341-03
-
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 3 Meter
-
Product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,1 m
763061-01
-
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
Product
Remote Cabinet and CO Splitters
3000 Series
-
Comtest's 3000 Series splitters are designed specifically for the European market. Their all-front connectors allow them to slot conveniently into ETSI racks at CO or a remote location—without the need for swing shelves. Cards are available for both POTS and ISDN and are compliant with ADSL2+ and VDSL technology.
-
Product
SHB12X-B12X, 73-Pin, Male InfiniBand to 73-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable 2m
192344-02
-
The SHB12X-B12X LVDS Cable connects the 12X InfiniBand connector on PXIe-656x LVDS instruments or some NI 658x LVDS Adapter Modules for FlexRIO with other NI accessories such as the SMA-2164 to break out cable signals for direct access. It is a shielded, 100 ohm cable that is offered in various lengths.
-
Product
802.11a,b,g Dual RF Shielded Test Enclosure
JRE 0814-2R-A
-
Containing all the capability of the larger JRE enclosures, the rack mounted 0814-2R-A is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices. Two independent 0814 series enclosures are mounted in one 19 inch rack. Two shielded vents provide excellent cooling and optional fan(s) are available for those hot products. Tough 'honeycomb' vents maintain shielding effectiveness throughout the frequency range. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
Mini Coax, Contact, ITA, RG316 Double Shield
610103152
-
Mini Coax, Contact, ITA, RG316 Double Shield.
-
Product
SH68M-68M-EPM, 68-Pin Male VHDCI to 68-Pin Male VHDCI, Twisted Pair, Shielded Multifunction Cable
190233-01
-
68-Pin Male VHDCI to 68-Pin Male VHDCI, Twisted Pair, Shielded Multifunction Cable - The SH68M-68M-EPM Cable, sometimes referred to as SHC68-C68-EPM, connects DAQ devices. The cable includes separate digital and analog sections, individually shielded twisted pairs for analog inputs, individually shielded analog outputs, and twisted pairs for critical digital I/O. The SH68M-68M-EPM Cable is offered in different lengths.
-
Product
Mini Coaxial Contact, Receiver, RG316 Double Shield
610104149
-
Mini Coaxial Contact, Receiver, RG316 Double Shield.
-
Product
Digital Cabinet X-ray System
XPERT 80
-
Kubtec's XPERT 80 brings high quality imaging and ease of use to science and research. The XPERT 80's compact self-contained cabinet, with a high resolution x-ray source, provides the sharpest images for every application. Optional sources are also available for micro-focus and soft x-ray applications.
-
Product
Magnetic Shielding Cabinet for EMI Testing
SDR-2000B
-
Cabinet Shell2mm galvanized cold-rolled steel sheetCabinet Door0.9*1.7m(L*W)0.6*0.6mCabinet Window0.3*0.3*0.025m(L*W*T) with 4mm holeN/APower Supply Filter30A/220V30A/220VInternet Line FilterRJ-45N/ACabinet Inside DecorationPVC ceiling, PVC plastic steel wall, 10mm wooden + 2mm galvanized steel sheet floorCabinet Inside Size2*1.2*1.8m0.8*0.8*0.8mAfter Packing Size2.2*2.3*2.3m1*1.1*1.2mAfter Packing Weight800kg200kgWorking With EMI-9KA/EMI-9KBEMI-9KA/EMI-9KB, PC, Testing load, and operator insideTesting load is inside to connect with EMI-9KA/EMI-9KB via BNC
-
Product
Instrument ER Shielded Cases
-
The Optima Stantron ER (shielded) and EX (unshielded) family of instrumentation cases are designed to house EIA standard 19” wide sub-racks and chassis. The rugged yet lightweight and stackable structural design is achieved with rigid front and rear aluminum bezels joined by rounded, extruded aluminum corner members. All panels - side, top and bottom are constructed of 18 ga. CRS. Select from a wide range of top, bottom and side panel options. Accessories for doors, shelves, power and co
-
Product
Circuit Breaker & Control Cabinet Simulator
SIM-CB6
-
The SIM-CB6 is the circuit breaker simulator that will make you an expert in breaker testing. The SIM-CB6 enables you to simulate any type of circuit breaker (SF6, Air Blast, Oil, etc.) up to 6 contacts (2 contacts per phase), with or without closing/opening resistor contacts and control cabinets. This simulator will allow you to increase your knowledge on circuit breaker analyzer systems to ensure full efficiency once on the field.
-
Product
Fixed Writing Surface for 24" RC Cabinet
WS-124
-
This fixed shelf / writing surface for a single-bay RC cabinet spans the full width of the cabinet and extends 18” in front.
-
Product
SH96F-96M-5, Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 5 Meter
786341-05
-
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 5 Meter
-
Product
SHC68-C68-D4, Shielded Single-Ended Cable, Low Leakage, 1m
152870-01
-
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
Full Extension Quick Disconnect Slides for 30"D Cabinets
IMS-85-C-19
-
Special order only. Friction slide yellow zinc steel slides. Ideal for mounting chassis into cabinets.
-
Product
RF Shielded Box
LTL A4001
-
Liveon Technolabs LTL A4001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL A4001 RF shielded test enclosure can comfortably house the intermediate device on test. LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
6 Ft Shielded Cable For All 5xxx/35xx (68 Pin)
GT95031
-
6 ft Shielded Cable for all 5xxx/35xx (68 Pin)
-
Product
68-Pin SCSI-II Female to 68-Pin SCSI-II Female, D-Type Shielded, 2m, Multifunction Cable
185262-02
-
68-Pin SCSI-II Female to 68-Pin SCSI-II Female, D-Type Shielded Multifunction Cable - The SH68-68-S connects compatible multifunction I/O devices to accessories or cables with SCSI-II connectors. 2m.
-
Product
802.11a,b,g RF Shielded Test Enclosure
JRE 0709-A
-
Containing all the capability of the larger JRE enclosures, the compact 0709-A is ideal for small wireless devices such as; 802.11a,b,g WLAN access points, VoIP devices and other small RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
Aspirated Radiation Shield
-
The fan has an ingress protection (IP) rating of 55, virtually eliminating moisture and dust ingress. At full speed the power requirement is 1 W (80 mA at 12 V DC). To conserve power fan speed can be reduced, via pulse width modulation (PWM), to 0.3 W at night or when wind speed is greater than 3 m s-1 without loss of accuracy. If the fan is continuously operated at full speed lifetime is rated at 50,000 hours (5.7 years). The fan includes a tachometer, allowing RPM to be mounted to detect obstruction of the fan.
-
Product
Splinter Shields
-
AMETEK Sensors, Test & Calibration
Splinter shields for use with materials testing machines are available to protect the user when testing brittle samples which are liable to fragment. The shields help prevent sample splinters from leaving the test area when performing a test.
-
Product
Shield Level / Pathloss Equipment
PAMS & PAMS-C
-
PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures. Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks. Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure. Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
Highly Shielded Phase Stable Assemblies
PhaseMaster® Enhanced
-
Does your application require cable assemblies offering some combination of phase stability and low loss, significant shielding effectiveness and increased durability?Consider Phase Master® 190E as your design-in option.Compared to similar phase stable cables, the Phase Master® 190E’s enhanced, multilayer shield construction yields:- A high level of phase stability vs. temperature- Reduced insertion loss & increased amplitude stability - Increased shielding effectiveness (120 dB @ 1 GHz, min)- Increased mechanical durability, especially torsion resistanceGreater connector retention (>40 lbs straight pull with SMA connectors)
