Product

Shield Level / Pathloss Equipment

SG1000B/PR1000A

-

Praxsym

SG1000B/PR1000A - Praxsym

The SG1000 Signal Generator and PR1000A Preamplifier have been designed to simplify the measurement of shielding integrity in a shielded enclosure. When coupled with a high stability spectrum analyzer and an appropriate selection of test antennas, the SG1000/PR1000A combination can measure shielding effectiveness at all of the NSA 94-106 (supersedes NSA 65-6) defined test frequencies from 1 kHz to 10 GHz.The PR1000A amplifies the received signal from the test antenna and overcomes the high noise figure of the companion test receiver or spectrum analyzer. The PR1000A will ensure that the system noise figure will be less than 4.5 dB at all test frequencies from 1 kHz to 10 GHz. When used with a spectrum analyzer measurement bandwidth of 100 Hz, the system exhibits a sensitivity of -150 dBm at the test antenna output.​To overcome high cable loss between the test antenna and the PR1000A assembly at 10 GHz, a remote low noise pre-amplifier (Praxsym PN 310-010091-001) is mounted directly onto the 10 GHz antenna.

Product

Arduino CAN Shield

IFB-10003-INP

-

Playing With Fusion Inc

IFB-10003-INP - Playing With Fusion Inc

CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!

Product

Expandable Embedded Box IPC With 10th Gen Intel® CPU

UNO-348

-

Advantech Co. Ltd.

UNO-348 - Advantech Co. Ltd.

Intel® 10th Gen socket type processor with DDR4 memoryScalable CPU, RAM selectionCompact, rugged and fanless design for harsh embedded environmentFlexible expansion with up to 3 x PCIe/PCI slots, 1 x M.2 (B-key), 1 x mPCIe & 2 x 2.5" SSDOptional iDoor expansionRemote out-of-band (OOB) power management with Advantech’s iBMC technologyBuilt-in TPM2.0 for hardware-based security

Product

Compact Embedded Box IPC

-

Advantech Co. Ltd.

Advantech Co. Ltd.

UNO-2000 box pc series serves as IoT automation gateways, offering flexible configurations with iDoor expandability and stackable modular design.

Product

DMX512 Test Box

GIZMO

-

Doug Fleenor Design, Inc.

GIZMO - Doug Fleenor Design, Inc.

The Gizmo is a DMX512 test tool with features useful for lighting system setup, testing, troubleshooting, and commissioning. With the Gizmo you can transmit, receive, save, playback scenes and perform a variety of data and cable tests.

Product

OTDR Launch Cable Box, OTDR Dead Zone Eliminator, 1KM-2KM

-

Shanghai Fibretool Technology Co.,Ltd.

Shanghai Fibretool Technology Co.,Ltd.

Designed to aid in the testing of fiber optic cable when using an OTDR. TheOTDR Launch Cable Box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.

Product

Box Compression Testing Machine

-

Dongguan Kejian Instrument Co., Ltd.

Dongguan Kejian Instrument Co., Ltd.

Containers are subject to compressive forces when stacked and during transportation. It is vital to determine the compression strength of the box in order to make sure that the box will be able to resist the anticipated compressive forces and to determine the load that the box will be able to withstand during transit and storage.

Product

Small Test Boxes

-

Cuming-Lehman Chambers

Cuming-Lehman Chambers

In today’s environment a small specific test box may be needed to test a component, perform R&D or simply tweak your product. Cuming Lehman Chambers has the ability to custom design and construct a precise test box to meet your specific needs.

Product

Modular Embedded Box PC With 11th Gen Intel® Core™ I CPU

UNO-2484G V2

-

Advantech Co. Ltd.

UNO-2484G V2 - Advantech Co. Ltd.

Intel® Core™ 11th i7/i5/i3 Processor with 8GB DDR4 3200Mb/s memory4 x GbE, 3 x USB 3.2 Gen2, 1 x USB2.0, 1 x HDMI 1.4, 1 x DP 1.4a, 4 x RS232/422/485Optional 2nd stack supports up to 2 x iDoor extension for expending wireless connectivity, industrial fieldbus or more I/OCompact fanless designRuggedized by zero cable and lockable I/O designSupports NVME storage with high data-transmission efficiency

Product

Resistor Calibration Boxes

RCB-3

-

Standard Electric Works Co., Ltd

RCB-3 - Standard Electric Works Co., Ltd

● The RCB-3 is used to verify and proof any High Voltage Insulation   Testers. It can be utilized to calibrate all High Voltage Insulation   Testers very accurately Analogs or Digitals.● Some institutions and large industries requested their own calibrator   too, therefore, SEW started manufacturing the RCB for special   customers.

Product

Camera Link Breakout Box

CLB-501B

-

Vivid Engineering

CLB-501B - Vivid Engineering

The CLB-501B Camera Link Breakout Box provides convenient access to the data transferred between camera and frame grabber over a Camera Link connection. All video, control, and communication data can be monitored and/or sourced via a standard header connector located on the rear panel.

Product

Edge-AI Box

DS-011

-

Advantech Co. Ltd.

DS-011 - Advantech Co. Ltd.

DS-011, an Edge-AI Box with 2 UHD HDMI ports, is designed for AI applications, making it ideal for interactive AI displays. Power by Qualcomm Dragonwing™ 8-cores QCS6490 2.1Ghz. Hexagon™ 770 AI Engine up to 12 TOPS. Triple-ISP for camera up to 192MP capture.

Product

Manual Switch Boxes

-

Robson Technologies, Inc.

Robson Technologies, Inc.

RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.

Product

MAX31855 T-Type Thermocouple Arduino Shield

SEN-30004-T03

-

Playing With Fusion Inc

SEN-30004-T03 - Playing With Fusion Inc

Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega

Product

Electrosmog Shielding

-

Gigahertz Solutions GmbH

Gigahertz Solutions GmbH

Gigahertz Solutions is your partner when it comes to shielding against electrosmog. We offer you products for shielding high-frequency fields as well as products for reducing low-frequency fields. Regardless of whether it is WLAN radiation, mobile phone radiation, Bluetooth or 5G; In our range for shielding from electrosmog you are guaranteed to find the right product with our shielding paints, canopies and shielding fabrics!