HV
electric power transmission is > 35,000 volts and for safety AC > 1000 and DC > 1,500.
See Also: High Voltage, High Voltage Switching, High Voltage Meters, High Voltage Detectors, High Voltage Programmable Power Supplies, Glove
-
Product
Variable Frequescy Resonant System
-
Yangzhou Power Electric Co., Ltd
Variable frequency resonant system for testing of long HV cables and GIL, for testing of short HV cables and GIS/GIL and for testing of long MV cables are designed for the generation of alternating current (AC) high voltage (HV) by resonant circuits with variable frequency, available of outdoor design.
-
Product
High Voltage Power Sources
-
Electronic Test & Power Systems
A comprehensive range of high voltage power sources are available from ETPS. Product families range from programmable high precision laboratory power supplies to HV Cassettes and PCB modules.
-
Product
Safety Testing
-
Whitelegg has over 80 years of experience in the design manufacture of market-leading electrical safety test equipment. Our unrivalled range of electrical test equipment serves a wide variety of safety testing and precision measurement applications for use in a variety of industries including manufacturing, construction, education, utilities, aerospace, calibration and anywhere else where there is a requirement for electrical safety testing or precision resistance measurement.Test equipment is cost effective, helps you to minimise expense, improve efficiency and increase profit. Whether you need electrical test equipment, environmental test, power analysers or HV Test Equipment, we stock the products to meet your demands, all backed by our first-class technical support if you have any problems using the equipment.
-
Product
Partial Discharge
-
Is a localized dielectric breakdown (DB) (which does not completely bridge the space between the two conductors) of a small portion of a solid or fluid electrical insulation (EI) system under high voltage (HV) stress.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 0.5m, HV
A009DF4-T-HA050
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
HV Tester
-
For High Voltage withstand, breakdown testing of electrical insulating systems.For Dielectric Strength testing of electrical / electronic components, small appliances, tools, motors, machines etc.
-
Product
Circuit Breaker Analyzers & Timers
CAT Advanced Series
-
DV Power circuit breaker analyzer and timer utilizes the latest technological enhancements for safe and fast testing of circuit breakers. The sophisticated design ensures efficient and reliable operations in high-voltage substations and industrial environments.The CAT Advanced series are stand-alone or PC-controlled digital instruments for a circuit breaker testing. The timing channels record closing and an opening of the arcing, resistor, and auxiliary contacts. Also, the main contact channels can measure the resistance value of the pre-insertion resistors (if present in the circuit breaker).With CAT Advanced series instruments, it is possible to record graphs of open and close coil currents. Furthermore, it records displacements of the HV and MV circuit breaker moving parts. Test results can be saved via USB, PC or be printed via 112 mm (4.4 inches) thermal printer (optional accessory) in tabular and graphical form.A circuit breaker test consists of different operational modes and CAT Advanced series supports:Open (O)Close (C)Reclose (O-0,3s-C)Trip free (CO)O-0,3s-COOpen-Close (O-C)Close-Open (C-O)Open-Close-Open (O-C-O)First trip (O)Multiple operations, such as Open-Close and Open-Close-Open, can be initiated by using a predefined delay time or by sensing a breaker’s contact position.The auxiliary inputs are used to monitor dry and wet auxiliary contacts. The six coil control analog channels measure and record coil currents simultaneously (OPEN and CLOSE), up to 35 A AC/DC.The additional six voltage analog channels have four selectable voltage ranges available (±1 V, ±5 V, ±60 V and ±300 V AC/DC).A built-in micro-ohmmeter generates up to 500A true DC ripple-free current with an automatically regulated test ramp that provides performing static and dynamic contact resistance measurement.Three transducer channels provide a measuring displacement of the circuit breaker moving parts, contact wipe, over-travel, rebound, damping time and average velocity. Also, a user can connect either an analog or a digital transducer to these universal channels.
-
Product
High Voltage Switching System
964i
-
The manual method is extremely problematic. Slow, error prone, labor intensive, operator hazardous – don’t even think about recording the test results. The 964i on the other hand, is purpose built to fully automate all of you HV switching needs. You chose the 964i, partnered it with a Vitrek 95X Series Industrial Strength Hipot Tester and QuickTest Pro test automation software. The company wins the Malcolm Baldridge National Quality Award, you get a promotion and that corner office you’ve always wanted. Choose carefully.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m HV, Exit Away From Pin 1
A050DM4-C-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 1m HV, Exit Towards Pin 1
A050DM5-T-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
UHF PD Detector
-
Handheld online PD substation surveying system. The UHF PD Detector is the ideal tool for quick, non-invasive surveys in MV and HV substations and should be part of the toolkit for all maintenance and service teams. Due to its high measurement bandwidth, the UHF method provides accurate local online partial discharge (PD) measurements on HV components such as cable end-terminations, surge arrestors, voltage transformers and isolators.
-
Product
High Voltage Personal Tester
HV/PT2
-
HV/PT2 is a compact, affordable, high quality proximity HV tester that is manufactured in South Africa. Your own personal HV tester is now available for you to wear at all times. A five position sensitivity switch enables the user to approach the HV source on the highest sensitivity at a safe distance.
-
Product
Cable Assembly, 50-Pin D-Type, Male To Female, 0.5m HV, Exit Away From Pin 1
40-970-050-0.5m-MF-HV
Cable Assembly
50-Pin Male to Female D-Type Cable Assembly, High Voltage, 0.5m Long, 45º Cable Exit Away From Pin 1.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m HV, Exit Away From Pin 1
A050DF4-T-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
High Voltage Tester
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI make high voltage tester is specially designed to test induction & submersible motors with cutting edge technology.High Voltage Tester is manufactured as per the International set standards and regulations. This High Voltage Testers are available in AC and DC types and are used for testing HV cables after installation and repair for ensuring efficient performance. It also indicates voltage withstands level and current leakage level of the cable during the testing period.
-
Product
Precision Voltage and Current Sources
VI-700
-
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
Product
Contact Resistance Test Sets
-
When a high current passes through a pair of mechanically independent metallic contacts, the resistance must be as low as possible. An increase in resistance can lead to additional degradation, as I2R losses will cause local heating of the contact surfaces. Our range of micro-ohmmeters measure both steady state and dynamic low resistance values. With test currents up to 600A available, logging and trending are also available on some models. We ensure that our Contact Resistance tests sets are portable, making them suitable for field measurements. Our contact resistance testers’ portability makes them ideal for a vast range of resistance testing across the entire LV, MV HV and EHV spectrum.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 1m, HV
A009DM5-T-HA100
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 2m HV, Exit Away From Pin 1
A050DM4-C-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 1m HV, Exit Towards Pin 1
A050DM5-050DM5-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m HV, Exit Away From Pin 1
40-972-050-0.5m-MU-HV
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Bus Differential System
B30
-
The B30 features integrated protection, control and metering for MV, HV and EHV busbars, providing cost effective, feature-focused busbar protection. Use the B30 to protect busbars with up to 6 feeders with up to two three phase differential zones. The B30 is a cost effective alternative to high impedance schemes, ideal for breaker-and-half bus schemes, with integrated feeder backup protection and metering
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 0.5m, HV
A009DM5-T-HA050
Cable Assembly
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 1m HV, Exit Away From Pin 1
A050DF4-T-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Ultrasonic Portable Hardness Tester
UCI-3000
-
Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.
-
Product
Cable Assembly, 50-Pin D-Type, Female To Unterminated With Ferrules, 2m HV, Exit Away From Pin 1
40-972-050-2m-FU-HV
Cable Assembly
50-Pin Female to Unterminated D-Type Cable Assembly, High Voltage, With Ferrules, 2m Long, 45º Cable Exit Away From Pin 1.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Tinned Ends, 2m HV, Exit Away From Pin 1
A050DM4-T-HA200
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Dual Channel HV Amplifier with Phase Inverter
A400DI
-
This unit contains two independent A400 amplifiers that share common ground reference and power supply. Please see A400 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase. Connecting a load between the outputs effectively doubles the amplitude range. Please note that the load cannot have any connection to ground.
-
Product
Ultrasonic Hardness Tester
-
Sinowon Innovation Metrology Manufacture Ltd.
◆ Perfect Accuracy——±3% HV, ±1.5HR, ±3%HB.◆ Microscopic Indentation—— Only high-power microscope can observe the indentation.◆ Quick Measurement——Result in 2 seconds.◆ Large LCD Display——Directly display measurement result, times count, maximum, minimal, average and deviation.◆ Friendly Operation——Operate well after short training.◆ Promised Warranty——2-Year warranty for main unit (Excludes Probe).◆ Mass Storage——Save 1000 groups measurement data.◆ Simple Calibration——Save 20 groups calibration data for invoking, improve calibration efficiency.
-
Product
HVDC Power Filter Characteristic Test Set
FT3000
-
FT3000 Power Filter Characteristic Testing equipment has the functions of automatic sweep harmonic signal output, A-F and P-F characteristic measurement/display etc. It can perform HVDC Power Filter Testing and is mainly used in AC filter of DC convertor station, DC filter tuning characteristics test and parameter test of R, L and C. It is also used in electrified railway HV filter, passive power filter client and conventional AC substation reactive compensation device.
