MUX
Combine multiple signals into one signal.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 50Ω, MCX
40-872A-101
Multiplexer Module
The 40-872A-101 (PXI) and 42-872A-101 (PXIe) are 50 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of the 40/42-872A has been minimized by careful attention to the mechanical and electrical design.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A
40-667C-012
Multiplexer Module
The 40-667C-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 24-Pole
40-571-102
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 75Ω, SMB
42-832A-002
Multiplexer Module
The 40-832A-002 (PXI) and 42-832A-002 (PXIe) are 75 Ohm 4 to 1 RF multiplexers with 2 banks in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, FC/APC Connectors, With Interlock
42-850A-014-M50-HI
Multiplexer Module
The 40/42-850A-014-M50-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI High Density Multiplexer, 1-Bank, 64-Channel, 1-Pole
40-610A-012
Multiplexer Module
The 40-610A-012 is a 1-bank, 64-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 2 Amp MUX, Single 32-Channel 1-Pole
40-635-101
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
950~2400MHz DVB-S 4 ways SAT-IF DWDM Optical Transmitter & Receiver
HDBS-4000DW
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HDBS-4000DW series, combine 4 pieces C-Band, 100GHz, ITU standard wavelength SAT-If optical transmitter, or optical receiver to one chassis, through DWDM, Make 4 ways optical MUX (TX) or DEMUX (RX), through one fiber, used in transmitting 4 ways different polarization SAT-IF signal of one satellite VL, VH, HL, HH with high performance. Installation flexibility.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, SMB
42-835A-001
Multiplexer Module
The 40-835A-001 (PXI) and 42-835A-001 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PXI Triple 4 To 1 RF Multiplexer, 8GHz 50 Ohm SMA, Terminated
40-882A-003
Multiplexer Module
The 40-881A-003 is a triple 50Ω 4 to 1 RF multiplexer with 8GHZ bandwidth.The 40-881A range of multiplexers have automatic termination of unused signals and are available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules.
-
Product
PXI Very High Density Mux 5 Ch 32 Pole
40-670A-022-5/32
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI 5A Power MUX, 8-Bank, 5-Channel
40-651-004
Multiplexer Module
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
Product
PXI High Density Mux 49 Channel 2 Pole
40-670A-021-49/2
Multiplexer Module
The 40-670A series of very high density multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI 2 Amp MUX, Single 8-Channel 8-Pole
40-635-004
Multiplexer Module
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Digital Multiplexers
-
Advanced Science and Novel Technology, Co., Inc.
High speed broadband 4:1 Multiplexer (MUX)Exhibits low jitter and limited temperature variation over industrial temperature rangeDifferential CML I/O data and clock buffersQuarter-rate clock outputSingle +3.3V or -3.3V power supplyPower consumption: 960mWFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 44 pin package
-
Product
PXI Single 18 Channel MUX, BNC Connectors
40-735-902-S3
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, FC/PC Connectors, With Interlock
42-852A-118-M50-HI
Multiplexer Module
The 40/42-852A-118-M50-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI 2 Amp Multiplexer, Dual 8-Channel, 2-Pole
40-635A-106
Multiplexer Module
The 40-635A-106 is a dual 8-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI Very High Density Multiplexer, 49-Channel, 4-Pole
40-675A-002-49/4
Multiplexer Module
The 40-675A-002-49/4 is a 49-channel, 4-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI High Voltage Multiplexer, 24-Channel
40-320A-101
Multiplexer Module
The 40-320A-101 is a single 24-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
Product
PXI Very High Density Multiplexer, 5-Channel 16-pole
40-670C-021-5/16
Multiplexer Module
The 40-670C-021-5/16 is a 5-channel, 16-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
PXI High Density Multiplexer, 4-Bank, 40-Channel, 1-Pole
40-615A-007
Multiplexer Module
The 40-615A-007 is a 2-bank, 80-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
High Density 1xN mux or 2xN Matrix Switching Systems
JX Series
-
This compact and economically priced series can be used as either 1xN multiplexers, 2xN matrices, or individual switches. As multiplexers, they can be used as a large number of individual muxes or jumpered together to form as large a mux as you need to switch a large number of inputs or outputs to one common port. As a 2xN matrix they allow you to switch any number of signals between two ports of a DVM, DMM, LCR, or other type of meter or supply. Individual relay modules are available for other configurations requiring discrete SPST or SPDT relays with standard or power relays.
-
Product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. The 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
PXI 10 x 4 to 1 RF Multiplexer 500MHz 50 Ohm Multiway Connectors
40-755-010
Multiplexer Module
The 40-755-010 is a 50 Ohm high density RF multiplexer (4 to 1) array with 10 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a Souriau multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
-
Product
Dual 2 Channel Fibre Optic Mux SC/PC
40-815-222
-
Pickering PXI Fiber Optic Multiplexers connect a single channel to one of two or four channels. They are available in single or dual multiplexer configurations supporting single-mode or multi-mode fiber. A wide choice of connectors types is available. The 40-810 multiplexer connects the optical channel by redirecting the optical signal into a selected output fiber.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, FC/APC Connectors
42-852A-018-M50
Multiplexer Module
The 40/42-852A-018-M50 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI 2 Amp Multiplexer, Single 8-Channel, 8-Pole
40-635A-004
Multiplexer Module
The 40-635A-004 is a single 8-channel, 8-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
RF Multiplexer 3GHz, 4 to 1
40-872-004
Multiplexer Module
The 40-872-004 is a 50 ohm 4-to-1 RF MUX available with 4 banks in a single PXI slot. Using modern RF relay technology, it features low insertion loss and low VSWR at an affordable price. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics up to frequencies of 3 GHz, with each path having a nominally equal insertion loss.
-
Product
Serializer/Deserializers & Selector Muxes
-
Serializer/Deserializer muxes use both rising and falling edges of the clock to serialize the data from parallel inputs to serial output while demuxes deserialize the data from its serial input to parallel outputs. Selector muxes routes the differential inputs to either one or more of the desired outputs upon assertion of the appropriately selected port. Muxes can be used in various applications including High Data Rate Ethernet, Fiber Communication, Signal Routing and Broadband Test & Measurement Equipment.
