LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
Evaporative Light Scattering Detector
ELSD-LTII
-
The ELSD-LTII utilizes a high-efficiency LED and enhanced digital signal treatment to minimize noise and deliver optimum sensitivity for trace analysis. An innovative cell design also reduces band broadening and allows sensitivity levels below 200 picograms. The high-performance optical detection system can also be used for combinatorial chemistry and high-throughput screening applications. The new Low Temperature Evaporative Light Scattering Detector (ELSD-LTII) is an easy-to-operate, universal detector that identifies analytes with uniform sensitivity regardless of their spectroscopic properties. It is not a spectroscopic detector. Instead, it removes the mobile phase through evaporation and then makes a light scattering measurement of the dried analyte particles.
-
Product
CANbus Controller for VMEbus
VME360
-
The VME360 CANbus controler is a 6U VMEbus board based on four SJA1000 CANbus controllers. Each SJA1000 provides an interface to the popular CANbus that supports both standard (11-bit) and extended (29-bit) identifier fields. Front panel LEDs provide diagnostical network information. The VME360 provides four CANbus interfaces. The CAN network is a serial communication protocol which efficiently supports distributed control with a high level of reliability.
-
Product
Monitor Solutions
-
Plura monitoring solutions were designed, engineered and built based on worldwide involvement with different technology segments, learned through hands-on experience which products were of high quality and value. The knowledge and experience that came from dealing with so many national & international projects from different types of applications ultimately led Plura engineering team to invent and create new technologies and products that comply with all the current and future video media standards from ST-259M/C to high complex IP ST-2110, ST-2022-7 & ST-2082.
-
Product
Handheld Water Quality Meters
LAQUA DO220
-
Measures dissolved oxygen (DO) concentration in ppm (mg/L) and % saturation0.01 mg/L or 0.1% DO resolutionCompensates salinity, temperature, and atmospheric pressure Allows up to 2 calibration points using galvanic DO electrode°C & °F temperature readingsWith real-time clock and date/time stamp for GLP complianceAuto log data; built-in memory can store up to 1000 dataAuto stable, auto hold, and real-time measurement modesAuto shut-off (programmable: up to 30 minutes)Built-in electrode holder allows 2 electrodes to be attached Monochrome LCD with white LED backlight: 50 x 50 mmPhono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slipPowered by 2 x AA batteriesPackaged with galvanic electrode in carrying case3 years meter warranty
-
Product
Customer Acceptance Test Panel
TA-65
-
DGS-65 Customer Acceptance Panel for both testing and trouble- shooting. We have added an option to the panel that allows you to select an analog slaving meter or the LED monitor lights as shown in the maintenance manual Fig. 5-14. The addition of the meter provides the technician with a more visible means to monitor the slaving "trend". The 50 pin DG connector is broken out on the panel to assist in monitoring or isolating unit signals.
-
Product
Wrist Strap Monitors
-
Single conductor (more commonly called single wire) ESD wrist strap monitors detect capacitance. These simplified monitors sense the input connection but do not discern precision resistance. They also offer additional value by monitoring the worksurface (ESD Mat) and the ground connection. The built-in LED offers local visual alerts, and a small piezo buzzer offers a nice clear audible alert to the operator at the bench.
-
Product
HMI Touch Screen Terminals
-
Panasonic Industrial Devices Sales Company of America
Panasonic HMI Touch Screen Terminals are among the brightest, sharpest and most flexible Operator Panels in the industry. Building custom interfaces has never been so easy or rewarding.Utilizing Panasonic's built-in tools like a time-saving 3D parts library allows quick and painless Operator Panel set up. From simple LED Displays to 12.1” 32,768 color touch screens, Panasonic has the HMI solution for any application.
-
Product
High-Speed Digital Output
-
High-speed digital output photocouplers (optocouplers) are optically coupled high-speed, totem-pole output isolators containing a GaAlAs LED on the input side and a photodiode and signal processing circuit on the output side in a single chip.
-
Product
High Power DC Electronic Load
IT8800 Series
-
IT8800 series has wide power range 150W~10KW, voltage and current measurement speed up to 50KHZ, resolution up to 0.1mV/0.01mA, adjustable measurement current rising speed 0.001A/us~2.5A/us, built-in RS232/GPIB/USB interface. IT8800 series has wide application fields because of its high performance products, it has been applied to LED lighting, aerospace, automotive electronics and other fields.
-
Product
LED/Laser Drivers for Display
-
Macom Technology Solutions Holdings Inc.
MACOM offers a leading-edge portfolio of LED and laser driver solutions for innovative OEM display products. Our programmable, low power, high-performance products are ideally suited for head-up and head mounted displays, multicolor LED/laser displays, backlight illumination applications, high current laser/LED systems and LCD/LCoS/DLP portable and pico projectors.
-
Product
Data Acquisition Module for Embedded Systems with IO60 expansion
IO60-M410
Data Acquisition Module
WINSYSTEMS’ IO60-M410 is a reliable data acquisition module for embedded systems with IO60 expansion featuring 24 GPIO (General Purpose Input-Output) tolerant to 30 V DC. Activity LEDs indicate device communication and DAC fault. WINSYSTEMS can provide custom configurations for OEM clients. Please contact a Applications Engineer through our contact page for details.
-
Product
Pulsed Source Measure Unit
-
The SpikeSafe SMU is a precision pulsed source measure unit that precisely sources pulsed current and simultaneously digitizes voltage. Optimized for precise and repeatable high-power LED and laser testing, SpikeSafe™ SMU (Source Measure Unit) current sources deliver precise pulsing with low microsecond rise times, low-jitter triggering and integrated digitizer for more accurate and repeatable high-power LED and laser testing.
-
Product
Light Flicker Meter
LiFli
-
The LiFli light flicker meter enables fast evaluation of light sources on the flickering part (flicker / flicker). Especially in the case of LED lamps, the flicker portion can be determined only by one measurement, since it is in the range of 0% to 100% for these luminous means.Audio features enable the flicker to be reproduced acoustically. A voltage output for further analysis by means of oscilloscope or voltage analyzer is available.
-
Product
Fiber-Optic Probes
Fiber-optic Probe
Designed with an unparalleled optical quality finish, Optomistic Products has developed a wide array of Fiber-optic Probes to accommodate your specific LED test requirement and mechanical constraints.
-
Product
7“ WSVGA,1000nit LCD
IDK-2107W
-
7" LCD supports 1024 x 600 pixels, Brightness of 1000 cd/m2 with LED backlight, Wide operating temperature (-20 ~ 70 °C) Projected Capacitive touch solution.
-
Product
LED Tester
-
Pocket-size LED tester.Easily check functionality, color, brightness and uniformity.Plug any leaded LED into one of 12 positions on the socket strip to test at current ratings from 2-50ma.The seven middle positions on the strip are set at 10 mA allowing comparison of LEDs in those spaces.Requires a 9V battery (not included).
-
Product
Programmable Setpoint RelayProtection Relay, Trip Relay
CRD-005 and CRD-020
-
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbulletCRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbulletCRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbulletCRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbulletLid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bulletRed LED lamp lights to indicate when the threshold level has been tripped
-
Product
Miniature High Resolution Underwater Color CCD Camera
L3C/LCC-720-L
-
The Teledyne Bowtech L3C/LCC-720-L miniature high resolution underwater colour CCD camera (with six integral high intensity LEDs) provides a low cost solution to general underwater viewing and observation, down to 1,000, 4,000 or 6,000 metres in confined spaces.
-
Product
Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron®, Intel® Q170, 4 PoE, 4 USB 3.0, And Real-time Vision I/O
IPS962-512-PoE
-
The IPC962-512-PoE meets the increasing requirements for maximum quality and flexibility in modern production plants. It features flexible expansion capacity, camera communication interfaces, real-time vision-specific I/O with microsecond-scale and LED lighting control. This machine vision controller is powered by the LGA1151 socket 7th/6th generation Intel® Core™ (codename: Kaby Lake/Skylake) and Celeron® processors (up to 65W) with the Intel® Q170 chipset. The IPS962-512-PoE comes with a full range of isolated I/O interfaces and real-time controls essential to machine vision applications, including trigger input, LED lighting controller, camera trigger, as well as an encoder input for conveyor tracking. The real-time vision system PS962-512-PoE enables a fast and high accurate inspection to ensure that the desired quality is achieved with no manufacturing defects. It supports four IEEE802.3at PoE LAN ports and four USB 3.0 ports for connection with industrial cameras. Operating over a wide temperature range from -10°C to +55°C, the IPS962-512-PoE provides reliable and stable performance within severe environments. Its easy setup and compact design are ideal for space constrained environments. Moreover, one PCIe x16 and one PCIe x4 expansion slots allow quick installation of I/O cards and graphics cards. Two easy-swappable 2.5" HDDs are available for extensive storage needs.
-
Product
Versatile Test Stand
VTS-2100
-
Applied Scientific Instrumentation
*Base is a Breadboard on 25 mm centers tapped for M6 screws with threaded holes for risers for TE/TI-2000, TE-300, IX-71/81, DMI, and MS-2000 stages.*Base feet provide vibration isolation.*Z riser is adjustable on pillar blocks.*Z motion from LS-50, LS-100, or LS-150 linear stage.*Z illumination can use LED, LED and a Condenser (from below), or fiber illumination (from above).*Observation is with a Modular Infinity Microscope.
-
Product
Digital Thermometer
SPRINT 8
-
Models with optional Green LED aiming diodes are available. This feature simplifies alignment when a measurement object is otherwise difficult to target. The Green LED spot size and location approximates the actual measurement spot size at the measurement distance. To make installation easy Sprint 8 is housed in a solid stainless steel tubular body with a 40mm x 1.5 external thread. Optional cooling jackets and air purges allow Sprint 8 to operate in hostile environments.
-
Product
LED Analyser
Feasa
-
Each LED Analyser allows for simultaneous measurement of up to 20 different light sources as it measures Color and Intensity – Brightness Test. Light from the LEDs is transferred by Plastic Optical Fibers and transported to the LED Analyser board for accurate measurement and analysis. The Feasa Analyser has been engineered to test LED’s and other lighting devices such as LCD Displays automatically. Intrinsic Quality offers a LED tester demo unit that can be tried out for two weeks free of charge. Currently available for purchase, call to order:
-
Product
Calibrating Equipment
-
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
Product
12.1" (4:3) High Brightness Modular Front Display Design Compatible With TPC-B520, TPC-B300 Models
FPM-D12T-HE
Panel PC
Sunlight readable with 1000 cd/m² luminance with 1024 x 768 resolutionHigh durability and performance with industrial-Grade LED LCDAdvanced projected capacitive (P-CAP) technologyIP66-rated front panel and panel mount supportUser-friendly system status LED indicators
-
Product
For PWS-872 And PWS-872FL
PWS Series Multi-bay Battery Charger
-
Supports up to 4 external batteriesCharging time: 4 hrCharge status LED indicatorsScrew holes for secure installationPower input: 19.5V/7.7ADimensions: 214.4 x 229.4 x 60 mm (8.44 x 9.03 x 2.36 in)Weight: 1.4 kg (3.08 lb)Packing material: XAASC-FSP150-RFBN2 (1 x 150w adapter)
-
Product
General Purpose Radiation Survey Meter/Geiger Counter
Rad 100™
-
The RAD 100™ is a general purpose radiation survey meter/geiger counter that detects and measures alpha, beta, gamma, and X-radiation. It is intended for personal safety and educational purposes. Like the popular Radalert® 100X, the RAD 100™ features a 3-second update on its digital liquid crystal display (LCD). The LCD shows the current radiation level in your choice of microSieverts per hour (SI units) or mR/hr for gamma radiation measurements. For mixed sources (alpha, beta, gamma) the CPM mode is recommended. This instrument also offers an accumulated total and timer function, up to 9,999,000 counts and 40 hours. A red LED blinks and a beeper chirps with each count (the chirp can be muted). This is a professional instrument that is also easy to learn to use and to operate, and carries the industry leading Medcom warranty (2 years overall limited to 1 year on the GM sensor). Many instruments designed by the Medcom team are still working perfectly after 30 years of use, so this instrument should provide a lifetime of useful information.
-
Product
4-Port Isolated USB 3.0 SuperSpeed Hub
USB-4630
-
2,500 VDC voltage isolation for upstream port4 downstream USB 3.0 SuperSpeed portsSupplied by external 10 ~ 30 VDC power or by USB bus powerESD protection up to ±8 kV (level 3)LED indicators for power-on and speed of each downstream port
-
Product
AC/DC Digitizing Power Meter
4015A（500V / 20A）
-
4015A Digital Power Meter is designed to measure the power line parameters of AC / DC and DC / DC power supply. It is suitable for AC / DC Adapter, Charger, Quick Charger, LED Driver and DC / DC Converter. It is also suitable for uninterruptible power supply UPS, Regulators AVR, Inverter, batteries, AC / DC power supply / components ... and other applications.
-
Product
Embedded Systems Projects
-
Precision Development Consulting Inc
Module Controller in Track System for silicon wafers, Static Headstack Tester, DOS Device Driver, LED Wafer Prober
-
Product
4 Digit Process Meter
CM2-PR
-
CM2-PR Process Meter has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option 2 relay output and an analog output or RS485(Modbus RTU Mode) communication.
