Ultrasonic Thickness Gauges
-
Product
Ultrasonic Leak Detection Camera
Leakshooter LKS 1000-V.2
-
1st ultrasonic compressed air, gaz and vacuum leak detector with camera. Specialy dedicated to visualize the spots where compressed air is leaking, the LEAKSHOOTER LKS 1000 – V.2 has many other applications such as : steam trap monitoring, bearing monitoring, electrical applications like partial discharge, corona effects, punctured isolators, electrical tracking detection.
-
-
Product
Gauge Type T Thermocouple Wire
W-TW-44P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Imaging Gauge Software Test System
-
The IMAGING GAUGETM quality analysis system was developed by APPLIED IMAGE to address the growing need to standardize the evaluation of camera image quality. The system includes a Test Chart manufactured using our ACCUedge® technology, along with unique Image Analysis Software, used together to analyze the quality of the imaging system, and then provide a summary report on the various image quality metrics. Our goal is to provide a simple to use, unique image analysis system, that can be utilized by R&D, scientists, system integrators, technicians and field operators to evaluate the camera quality or imaging system.
-
Product
Mechanical Force Gauges
-
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
Product
Flaw Detector & Thickness Gauge
DFX-8+
-
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
Product
Precision Gauges
WP-Series
-
Precision gauges to test the dimensional tolerances and requirements of many different types of products. The gauges are designed to verify the quality & safety characteristics of products,
-
Product
Height Gauges
V4
-
The height gauge V4 have been developed for the most difficult workshop environments. Manufactured in their entirety in Switzerland, they will guarantee a robust, precise and reliable product on the long run.
-
Product
Harness Testers/Thickness Gauge
-
Our Hardness Testers/Thickness Gauges includes premium models such as the EMHT40, UTEMHT20 and UTEGEMTT2. These testers are precision instruments designed to measure the thickness or hardness of most metals. Two cost effective units - FHT801 and FHT803 are tailored to agricultural applications such as checking the ripeness of fruits and vegetables in fields/warehouses.
-
Product
Strain Gauges
TSM
-
We have been designing and manufacturing strain gauges for over 50 years and one of the earliest members of the British Society for Strain Measurement: Linear Strain, Dual Strain, Full & Half Bridge, Rosette & Circular, Bonding Services, Torque & Shear Strain Gauges and Bi-Axial/Tri-Axial Strain Gauges.
-
Product
Gauges & Calibrators
-
Ralston Instruments' gauges and calibrators are born from decades of experience working with technicians, project managers and facilities teams responsible for maintaining metrology instruments.
-
-
Product
WT Series Digital Pressure Gauge
-
AMETEK Sensors, Test & Calibration
The WT version of the XP2i is designed to replicate the dimensions and pressure connections of the most common test gauges mounted in portable cases. It is a drop in replacement for a Wally Box Pressure Gauge.
-
Product
Coating Thickness Meter
MEGA-CHECK DX
-
The List-Magnetik MEGA-CHECK DX Coating Thickness Gauge can be connected to a wide range of specialized digital probes. Applications on very small apertures, thick layers and small measuring points are easily possible.
-
Product
SENSOR FOR THICK & CURVED MATERIALS
S3
-
The smallest, simplest, most affordable high-precision non-contact sheet resistance sensor availableNon-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterReads any conductive coatingon even the thickest nonconductive substratesOptions include PC-based productivity software, stage, and morePerformance limited by "lift off" phenomenonelevation of sensor above conductive layer must be carefully controlled
-
Product
Handheld Ultrasonic Flow Meter for Liquid
P117
-
Gentos Measurement & Control Co.
P117 is a hand-held flow meter equipped with external clip-on transducers, which can meet the needs of convenient and fast flow measurement, allowing you to quickly transfer and measure data between different working environments and improve work efficiency.
-
Product
Dimensional Gauging Systems
-
Marposs provides a complete line of solutions for dimensional gauging, both manual and automatic. We work closely together with our customers to design tailor-made applications according to their needs and requirements, whether the quality control is performed for off-line sample-based or integrated automatic production lines. We complement these solutions with made-to-order Calibration Masters (rings, plugs, part-like masters and master gears).
-
Product
SSG Series Strain Gauge Extensometers
-
Shimadzu’s SSG series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards, including those for plastics and metallic materials These lightweight, precision extensometers feature a wide elongation measurement range, while retaining the flexibility to measure using small gauge lengths, and support both rod and flat plate shaped specimens. Consisting of an elongation sensor and amplifier, this extensometer is suitable for use with metals and hard plastic materials, and is fastened securely to specimens with screws. Calibration using an extensometer calibrator allows the extensometer to meet JIS and ISO Class 0.5 and ASTM Class C standards for higher accuracy.
-
Product
Low Gauge Vacuum Tester
G4103
-
Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)
-
Product
Thermocouple Vacuum Gauge Tubes for Medium Vacuum
DV-6 Series
-
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.The Teledyne Hastings’ DV-6 series thermocouple vacuum gauge tube acts as a localized sensor which is then paired with a selection of meters or controllers to provide reliable, cost-effective measurements in diverse applications. The robust sensor gauge tube is easily installed into vacuum systems and when properly excited, generates a thermoelectric voltage to provide a vacuum pressure measurement based on gas density. The DV-6 thermocouple vacuum gauge tube fully compensates for temperature and rate of temperature change.Thermocouple gauge tubes are calibrated on vacuum systems that contain N2 or Air, but can be used with other gases. Additionally, thermocouple gauges and their controllers can be recalibrated when a replacement thermocouple gauge tube is installed, following instructions in the manual. However, our DB-20 reference tube is available to confirm meter/controller performance. A complete line of installation accessories are also available to simplify the integration of our thermocouple gauge tubes into a variety of vacuum systems. Our goal is to provide “one less thing to worry about”, when performance matters! With a wide range of meter, fitting, relay and output options, the DV-6 series provides a reliable pressure measurement in numerous industries and applications.
-
Product
Force Gauge
-
The Centor range of digital force gauges offers force measurement solutions for every situation. From the simple Centor First II force gauge to the colorful Centor Easy II, we have a wide range of instruments designed for industrial and laboratory use.
-
Product
CORROSION GAUGE
MX-1
-
The MX-1 will hold a single velocity, making it the perfect choice applications where only one material is being tested day after day. With the preset velocity in the gauge, you simply turn it on and go to work. The tool's backlit display is easy to read, even in dim light conditions, and the unit operates for up to 200 hours on a single set of AA batteries. The MX-1 comes complete, ready to use, and is protected by Dakota Ultrasonics 5 year limited warranty.
-
Product
Flatness, Bow, Warp, Curvature, Glass Thickness
Standard Warp Measuring System
-
Optik Elektronik Gerätetechnik GmbH
Optical, non contact measurement of warp and bow of specimen with size up to (1600 x 1200) mm. The system is designed for the contactless, optical measurement of the curvature (Warp) horizontal, coated float glass substrates. For that measurement the heights on different measuring points is evaluated.
-
Product
Pressure Gauges
-
Diaphragm pressure gauges feature stainless steel construction for superior chemical and corrosion resistance for your intermediate pressure measurement applications. Because of the protective diaphragm seal design, these pressure gauges are ideal for use with viscous as well as corrosive fluids. Optionally, these diaphragm pressure gauges may be ordered with glycerine filling to help dampen the effects of machine vibration and pulsation of the media.
-
Product
Pressure Gauges
-
Digital and analog pressure gauges in absolute, barometric, gauge, differential, sealed gauge, and vacuum pressures in a variety of pressure units including bar and psi up to 25,000 psi.
-
Product
Deflection Gauge Extensometers
-
We supply a wide range of deflection gauge extensometers ideal for measuring deformation in three and four point bend tests and in compression testing applications.
-
Product
Ceramic Capacitor Input Water Level Gauge
HR8008
-
HighReach Measuring & Controlling System Co.,Ltd
HR8008 is a high-precision pressure water level gauge that monitors surface water or groundwater level and water temperature for a long time. It uses ceramic pressure sensitive components with good stability, high precision and strong overload capability. It adopts advanced mixed signal processing technology. Full-scale digital linear correction can be realized, digital temperature error compensation in full temperature zone; compensation parameters are stored in non-volatile memory, multiple safety protection mechanisms are avoided, and products cannot be used due to loss of calibration parameters; Monitoring function effectively preventing accidents such as crashes and program runs, and greatly improves the reliability of the product.
-
Product
Needle Pressure Gauge
102
-
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
Product
Distance, Coating and Thickness Meters
-
PeakTech Prüf- und Messtechnik GmbH
This professional laser distance measuring device with multi-line LCD display, which has a backlight, was specially designed for high-precision distance measurements.
-
Product
Destructive Coating Thickness Gauges
-
Designed for measuring on a non-metallic substrate or assessing the thickness of a multi-coat paint, Elcometer offer a range of destructive coating thickness gauges such as the Elcometer 121/4 and Elcometer 141 that are portable and easy to use.
