ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
-
Product
Handheld Performance Tuner
Max Energy
-
Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel giving you more miles at part-throttle and more power at wide-open throttle. In order to increase engine efficiency, horsepower and torque, our engineers first optimize the spark and fuel curves point by point over the entire rpm band. With the additional power and optimized transmission functions, drivers use less fuel to accelerate and maintain cruising speeds without the torque converter un-locking and transmission down-shifting to a lower gear. The results are maximum power and fuel mileage.
-
Product
Power modules
-
G.R.A.S. Sound & Vibration A/S
It provides polarization voltage for the transducer, ensuring that the microphone gets the charging voltage it needs.It provides supply voltage for the microphone preamplifier. The preamplifier acts as a unity gain impedance converter. It provides a certain amount of line drive capability by providing a low output impedance and output current, making it possible to transmit the signal from the transducer to the Power Module without significant degradation.A power module can provide amplification or attenuation to the signal, thus making it possible to fine tune the measurement chain to the signals being measured and the hardware being used.Selectable filters make it possible to exclude unwanted noise from the measurement, e.g. wind induced noise from outdoor measurements.Overload detection makes it possible to validate the measurements and is a useful tool in monitoring setups.When a Power Module with gain is used, you can use longer cables because of the power module's ability to deliver current.A Power module introduces electrical isolation
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-6 FPGA - XMC
Model 71620
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronization- PCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- RoHS Compliant Lead-Free Version Available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Angular Orientation Sensor
WOS-120
-
The Miniature Angular Orientation Sensor system Model WOS-120 contains both a 3-axis fluxgate magnetometer and a 3-axis accelerometer. These sensors are sampled by an internal A to D converter and microprocessor subsystem which outputs 16 bit digital data representing the magnetometer and accelerometer readings. The system can also be configured to transmit the roll, pitch and azimuth orientation angles of the Model WOS-120 system. These angles are calculated before transmission from the accelerometer and magnetometer sensor output data.
-
Product
Precision Microcontrollers
-
Analog Devices provides a range of analog microcontrollers featuring ARM® Cortex™-M3 processors that help enable this product portfolio’s high precision, high performance, and low cost. By featuring ARM Cortex-M3 processors, our devices include a rich support system to aid product development throughout applications that include optical networking, industrial control, point-of-care diagnostics, and a variety of other industrial, instrumentation, and medical uses. Precision analog blocks including, but not limited to ADCs, DACs and references allow for precision control and measurements. Included also is the ability to read back diagnostics, which is a key requirement in the above applications.
-
Product
16 Channel Multievent Peak Sensing ADC
V785N
-
The Model V785N is a 1-unit wide VME 6U module housing 16 Peak Sensing Analog-to-Digital Conversion channels. Each channel is able to detect and convert the peak value of the positive analog signals (with >50 ns risetime) fed to the relevant connectors. Input voltage range is 0 ÷ 4 V. The Mod. V785 N features LEMO 00 connectors for both input and control signals.
-
Product
DALI 0-10v Converter
-
The DALI 0-10V Converter converts DALI signal to the Analog 0-10V protocol.
-
Product
JadeFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
Model 5983-313
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- Four 250 MHz 16-bit A/Ds- Four multiband DDCs- One digital upconverter- Two 800 MHz 16-bit D/As- Extended Interpolation- Sample clock synchronization to an external system referencePCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical interface for backplane gigabit serial interboard communication- LVDS connections to the Kintex UltraScale FPGA for custom I/O and synchronization- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions availablePlease refer to the product datasheet for Installed FPGA IP Module details
-
Product
Advanced Antenna Acquisition & Analysis
SW-A4
-
Introducing Advanced Antenna Acquisition and Analysis (A4), the newest antenna measurement software from NSI-MI, expertly engineered for data collection, analysis, automation, and plotting. A4 builds upon the decades of experience and optimization built into NSI-MI’s legacy software platforms, NSI2000 and MI-3000, while adding modern features and capabilities that meet the challenges of today. A4 seamlessly blends the user-friendly interface of NSI2000 with the performance and versatility of MI-3000. Its intuitive design and powerful Application Programming Interface (API) deliver the adaptability needed to handle even the most challenging measurement tasks. A4 offers multicore, multithreaded support to greatly improve processing time while adding the ability to parallelize analysis and transformation tasks. Choose the perfect solution with NSI-MI's four software tiers, each packed with tailored features to match your specific requirements. Let NSI-MI help you choose the ideal package to fully unlock the potential of your antenna measurement range.
-
Product
PCIe 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels
M4I.4480-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Embedded LO Capability
S95084B
-
The S95084B software tunes the analyzer’s receivers to the output frequency of the converter under test without the need for access to internal LOs or a common reference signal.
-
Product
Current to Digital
-
Analog Devices’ breakthrough current-to-digital converter technology is backed by award winning expertise to help solve your medical, industrial, and security application needs. Our high speed, high resolution ADC modules enable improved CT scanner data acquisition, photodiode sensors and power monitoring, spectroscopy, and high channel count data acquisition systems.
-
Product
S-video Format Converters
-
Many of our products have an S-video option.For a full list, use the site search at the top of this page.
-
Product
Fibre Optic Converters
-
In complex testing environments it is often needed that electrical signals have to be transmitted into the chamber or out of the chamber to the test equipment.For that purpose we offer a variety of different interfaces that convert electrical signals into optical signals and back. Such the signal can be transported via fibre optics and is immune against electrical fields.
-
Product
Data Acquisition Device A2D / D2A
-
General Features10 DAC channels5 ADC channelsDifferential or single ended IOs Full scale bipolar or unipolar signaling
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 5 Channels, 2.5 GS/s on 10 Channels, 1.25 GS/s on 20 Channels
DN6.225-20
Digitizer
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
4 Channel DAC FMC Module
DACNF04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
Product
Measurement
Power Meter
-
Power Meter is used for determining the power of the electrical current coming to the input channels of ADC modules and FFT spectrum analyzers, or that of the electromagnetic signal.
-
Product
Utility Power Source
SE-UDPS
-
Load boards for applications like mixed signal, analog and RF require active components. To drive these active components multiple utility power supplies are needed. The SE-UDPS from Salland Engineering is an economical way of adding more utility power supplies to your Advantest™ V93K to drive op-amps, buffers, relays and switches. The SE-UDPS extends the usefulness of your current fleet of V93Ks. You can also minimize the need to add external power supplies on your load boards.
-
Product
Web Sensor Hygrometer
T3511-4
-
Web Sensor with relative humidity and temperature probe. The device is supplied with T+RH probe on the cable.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
-
Product
Dual MAX31865 PT-1000 RTD to Digital Breakout
SEN-30202-PT1K
-
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information.
-
Product
Accessories
-
Spectrum Accessories: Cables, A/D External Pre-Amplifiers, D/A Amplifier Card, Clock and Trigger Distribution, Docking Stations
-
Product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SOSA Aligned 3U VPX
Model 5553
-
- Supports Xilinx® Zynq® UltraScale+™ RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- 10 GigE Interface- 40 GigE Interface- Optional VITA 67.3C optical interface for backplane gigabit serial communication- Dual 100 GigE UDP interface- Compatible with several VITA standards including: VITA 49, VITA 46, VITA 48, VITA 67.3C and VITA 65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Model 8256 3U VPX SOSA Aligned Development Chassis- Model 6003 unique QuartzXM eXpress module enables migration to other form factors- Video: Model 8256 3U VPX SOSA Aligned Development Chassis- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Synchronize up to eight modules with Model 5903 High-Speed System Synchronization and Distribution Amplifier - 3U VPX- Please refer to the product datasheet for Installed FPGA IP Module details
-
Product
IRD
SFT358x
-
Hangzhou Softel Optic Co., Ltd.
SFT358X IRD is a new design which integrates demodulation (DVB-C, S/S2 optional), de-scrambler and multiplexing in one case to convert RF signals into TS output.
-
Product
ARINC 818 to DVI Converter
-
The ARINC 818 to DVI converter is a rugged standalone module available in 6U cPCI form factor used for ARINC 818 to DVI conversion, DVI to ARINC818 conversion, ARINC 818 Mux as well as ARINC 818 Duplicator either on front panel or via cPCI back panel. It is a video Converter module designed with Cyclone V GT FPGA, using Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
Product
Encoders
-
Panasonic Industrial Devices Sales Company of America
Panasonic Encoders convert the manual rotary operation of an actuator or knob into coded signal outputs. The operation is similar to Potentiometers but the output signal is different in that it is a repeated pulse signal rather than a continuous analog signal. Panasonic Encoders offer options such as high torque, push lock, long life, push-on switch, water proof and center space.
-
Product
Diving Technology Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
The imaging ultrasonic testing systems of the USPC 30XX series are optimized for testing a wide variety of materials and provide high-resolution findings in the form of A, B, C, D and F images. The hardware consists of an industrial PC, in which a motor controller and an ADC card are installed, as well as a HILL-SCAN pulser/receiver unit. An overview of the available systems is given in Table 1.
-
Product
BRI, PRI and PSTN FXS Simulator
emutel Max
-
emutel Max is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Max can emulate different country specific networks by adding network personality cards " networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Max.
-
Product
Hardware/Software for Increased Production
VibLink & NavLink
-
The VibLink system - Each vibrator, plus the central recorder, is equipped with a VibLink module. The VibLink module uses advanced TDMA techniques to multiplex seven vibrators and the doghouse on one radio channel. And does this all in one second windows. With additional Vibrators, additional seconds are added. The Universal Encoder 3 uses its time slot to send out status updates and request PSS/PFS data. Each Force 3 controller uses its time slot to send out its location, status, and QC Information.
