ADC
quantization of an analog signal into a digital signal.
See Also: Analog-to-Digital Converters, FPGA, Transducers
-
Product
MIMIC® JUNOS Simulator
-
MIMIC JUNOS Simulator fully supports Juniper JUNOS® software and SNMPv1, v2, v2c, v3. Up to 100,000 devices can be simulated in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. An extensible environment allows new MIBs and devices to be added to the simulation.
-
Product
350 MHz Universal Frequency Counter/Timer, 12 digits/s, 20 ps
53230A
-
The Keysight 53230A universal frequency counter/timer serves all your frequency and time interval measurement needs. In addition to the typical frequency and time interval measurements, continuous/gap-free measurements are available for basic modulation domain analysis. Optional burst measurement software is available. An optional microwave channel can be added to measure 6 or 15 GHz.
-
Product
Digital Power Meter
66205
-
The 66205 is the 2nd generation of the 66200 series power meter designed specifically for single channel measurement. Its state of art design is capable of providing highly accurate power measurements to meet the requirements of IEC 62301/EN50564 standards. Functionality improvements of the 66205 increase power measurement capabilities to a wider range of applications. The Smart Range function is one of the most important new features added to the 66205 power meter. Smart Range allows the power integration mode to perform active power measurements with the measurement range in auto mode. Chroma’s proprietary design automatically selects the appropriate range, based on changes in sensed voltage and current, ensures the best accuracy when integrating the measurements over time. The 66205 provides 10 selectable current measurement ranges from 5mA up to 30A. External sensor options A662017~A662020 are available to increase the current measurement range. Six selectable voltage ranges are available up to 600V.
-
Product
6-Channel VME Buffered Electrical-to-Optical Converter
V720
-
The V720 is a six-channel logic-level electrical-to-optical converter, packaged as a single-width, 6U VME module. It may be used with compatible Highland optical receiver modules for fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
Product
OnyxFX FlexorSet 8-Channel 250 MHz A/D with DDCs - 3U VPX
Model 5973-317
-
- Supports Xilinx Virtex-7 VXT FPGA- GateXpress supports dynamic FPGA reconfiguration across PCIe- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)Ruggedized and conduction-cooled versions available
-
Product
3U cPCI I/O & Comm Board
75C3
-
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
LAN⇔RS-422/RS-485 Converter (Insulated, Wall-hanging Model)
SI-65FA-L
-
SI-65FA-L is an interface converter to connect equipments such as equipment for factory automation or analyzers which have RS-422/485 communication ports to LAN.
-
Product
1 GHz A/D and D/A with Virtex-6 FPGA - XMC
Model 71630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- One 1 GHz 12-bit A/D- One 1 GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Front panel clock/sync bus for multimodule synchronizationPCI Express (Gen. 1 & 2) interface up to x8 wide- Optional user configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Synchronize up to four modules with Model 7192 System Synchronization and Distribution Amplifier - PMC/XMC- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
Power Electronics Solutions
-
Scientech Technologies Pvt. Ltd.
Power electronics has found an important place in modern technology being a core of power and energy control.The subject of Power Electronics is the merger of the field of electrical power system and solid state electronic devices. It is the discipline that involves the study, analysis, and design of circuits that convert electrical energy from one form to another. Almost all the new electrical and electromechanical equipment contain power circuits.
-
Product
RF Acquisition Record and Playback Instrument
SARP-6
-
Saluki SARP-6 RF Signal Acquisition Record and Playback Apparatus is a portable RF signal acquisition record playback equipment. It can be used to directly acquire, record, and playback RF signal from 1MHz to 6GHz. Its data recording and bandwidth playback can reach 200MHz. The SARP-6 RF Signal Acquisition Record and Playback system is composed of up and down inverter module, high-performance ADC and DAC, and large capacity solid-state FLASH or high-performance disk. It is widely used in radar, GPS, communication, telemetry, as well as many other circumstances for civil purposes when acquiring signal and recording it down.Applications: Interference Analysis/Surveillance/Spectrum Management/Satellite Communications
-
Product
Pin Converters
-
Blackhawk provides several different emulation pin converters to fit Texas Instruments standard JTAG target headers. This includes 14-pin TI, 20-pin cTi & ARM, 10-pin ARM, 60-pin XDS560 Trace and System Trace. All pin converters are available from the our Online Store or an authorized Blackhawk reseller.
-
Product
Gen 4 X16 PCIExpress UltraScale+ FPGA Carrier Board
PG4
-
The PG4 continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD UltraScale+ FPGA computing power. The PG4 is a PCIExpress, Gen 4 x16, FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications. The AMD UltraScale+ VU33P delivers impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PG4 FPGA processes input from the FMC+ HPC (Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 12.0GSPS).
-
Product
PXI FlexRIO Digitizer
-
PXI FlexRIO Digitizers feature high-performance analog-to-digital converters with lightweight analog front-ends designed to maximize sample rate, bandwidth, and dynamic range. These modules use FPGAs from Xilinx alongside LabVIEW and Vivado programming options for custom algorithm implementation and real-time signal processing. For applications that require high channel counts, PXI FlexRIO Digitizers use the NI-TClk API and the timing and synchronization capabilities of PXI to achieve sub-sample synchronization between multiple modules in a chassis. These modules also feature an auxiliary I/O connector with GPIO for triggering or digital interfacing and the option for high-speed serial communication.
-
Product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
-
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
PCIe 16 Bit High Speed Digitizer - 250 MS/s on 2 Channels
M4I.4420-X8
-
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
GPIB Controller Card
GPIB-PCI-E
-
The GPIB-PCI-E is a PCI Express GPIB controller card that converts any PC with a PCI Express slot into a GPIB controller.
-
Product
Modular Breakout System for Hardware-In-Loop Simulation
-
Designed in partnership with OPAL-RT Technologies, this Modular Breakout System combines a BoB feature set with the added flexibility of an FIU. By mating the FIU chassis directly to the BoB using our plug-in modules, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
Product
Flying Prober Test
QTOUCH1202C
-
Qmax Test Technologies Pvt. Ltd.
he Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.The V-I signature test shall be in-built in the Prober system with “ Best fit Curve “ algorithm .Provision for adding various external Test & Measurement instruments like GPIB / USB / PXI Instruments is available.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 16 Channels, 16 Single-Ended Inputs
DN2.592-16
-
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
USB Converter Cables
-
These converter cables connect various serial interfaces to a computer USB port.
-
Product
SCSI Converters
-
Paralan's wide product line of SCSI Converters permits different SCSI Bus types to communicate with ease and reliability, and with no loss of data throughput.
-
Product
Signal Acquisition
277
-
The Model 277 is designed around the Texas InstrumentsADS42LB69 16-bit ADC. The 250 MHz sample clock issupplied by either the on-board frequency synthesizer or anexternal source. The frequency synthesizer can be phaselocked to the local 10 MHz TCXO or an external referencecan be used to achieve system-wide phase coherence.
-
Product
Flocculation Jar Tester
LD-LFC-A11
-
Flocculation Jar TesterLD-LFC-A11is designed to stimulate the process of adding reagents, precipitation, coagulation reaction which occurs in water testing procedures. Features portable, 4 round shaped beakers, each with 0.6 L capacity. With 10 to 1000 rpm speed, this flocculation jar tester conducts synchronous as well as independent running operations. It is used to carry out the jar test during water treatment procedure.
-
Product
Synchro Power Amplifiers
SSP
-
Computer Conversions Corporation
The SSP Series are Compact, Reference Powered and Isolated Synchro Power Amplifiers, and AC Sine/Cosine ( Resolver ) to synchro converters; designed for moderate wattage, and re-transmission requirements; providing ultra high efficiency, and ultra high reliability in service, and ease of use. They are ideally suited for demanding Naval/Maritime, Aircraft, and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and active control systems. They are suitable to drive both CT and CDX type passive loads, and virtually any synchro input instrumentation, or control.
-
Product
XMCspan XMC Expansion Board
XMCspan
-
The XMCspan allows users to customize and expand I/O options when coupled with VMEbus SBCs, adding up to 4 XMC or PMC slots.
-
Product
Taper System, CCD Beam Imaging Camera
TaperCamD series
-
355 to 1150 nm, standard CCD detectorHyperCal Dynamic Noise and Baseline Correction software (Pat. Pending)CTE Comet Tail Elimination for > 900 nm (Pat. Pending)Port-powered USB 2.0; flexible 3 m cable, no power brick14-bit ADC, 4 MB image buffer & on-board microprocessorWindow-free sensors standard for no fringing25,000:1 electronic auto-shutter, 40 s to 1000 ms1,000:1 SNR (30/60 dB Optical/Electrical)
-
Product
PCIe 16 Bit Multipurpose Digitizer - up to 40 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5932-X4
-
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Compressed Air RH+T+Tdp Sensor
T0211P-4
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Precision Flying Probe Platforms For Automated Test Applications
-
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design.Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
