Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Amplified Spontaneous Emissions (ASE) Sources
-
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
-
Product
Solid-State RF amplifier module for High Power Testing
-
Exodus Advanced Communications
Exodus introduces the AMP1071 - a Solid-State RF amplifier module covering the entire ultra-wide 2.0-20.0GHz frequency range instantaneously at 20W CW minimum. Using State of the Art GaN devices, the AMP1071 operates from a 32VDC source at less than 10A consumption. This module is suitable for use with all single channel modulation standards and applications requiring high power and ultra-wide band coverage. It has built-in protection circuits, high reliability and ruggedness. Typical applications include High Power Testing, EMI/RFI, EW and Communications and Jamming.
-
Product
USB Preamplifier, 100 MHz to 26.5 GHz
U7227C
Amplifier
The U7227C, 100 MHz to 26.5 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
Amplifiers
-
Fully automatic, legal limit plus headroom amplifierAlpha’s low-drive, tube amplifier design delivers the cleanest possible signalOperates on all Amateur Radio Bands 160M thru 10MSingle, easy to find, inexpensive 3CX1500A7 8877 type tubeInternal, automatic 4 port antenna switch capable of combining any 2 antenna portsAlpha’s Legendary service and support4 year limited warranty on hardware, 1 year on tube1500W, 100% duty cycle, no time limitation, key down foreverRugged construction built to last
-
Product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
-
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
-
Product
Amplified Photodetectors
-
Hinds Instruments' photodetector modules are specifically designed for use with high frequency optical signals including those generated in Photoelastic Modulator (PEM) applications.
-
Product
Amplifier, Switch and Test Box
CLIOQC Model V
-
The QCBOX Model 5 is a non-conventional unit designed to fulfil actual and future needs of an electro-acoustical analyzer like the CLIO system. It is USB linked to a PC and can be configured, with dedicated software controls, to assist frequency response and impedance measurements or to perform DC measurements. Using it for frequency response measurements acts as 50W power amplifier to drive the speaker or network under test while routing one-of-four inputs to the analyzer as well the current sensing output. The four inputs are able to provide a phantom power supply both for Audiomatica or general purpose microphones (0-24 V range, software controlled). Impedance measurements can be done either switching the D.U.T.’s load across the analyzer’s input or using a dedicated output, ISENSE, thus allowing impedance measurements in constant voltage mode as well voice coil current distortion analysis. An internal ADC measures the DC current into the voice coil. Thanks to an internal software controlled voltage generator the speaker can be driven with a superimposed DC voltage (±20V), allowing for measurements of large signal parameters. Two ADC converters with a ±2.5 V and ±5 V are available at inputs 3 and 4 to measure the displacement with a laser sensor or any other DC signal. A dedicated digital input handles an external foot pedal switch (or TTL signal) to be connected and triggers QC operations. A 6 bit output – 5 bit input TTL digital port is available to interface the QCBOX and driving software with external hardware (like turntables for example).The QCBOX Model 5 finds use both in laboratory for R&D applications and in production lines setups.
