Diesel
a light fuel oil.
-
Product
Diesel Smokemeters
-
our super fast MoT approved new generation smokemeter package. Similar to the AGS gas analyser, it is also approved in almost all European countries to the highest and latest specifications.
-
Product
Diesel Engine Tachometer
GE-1400
-
Handheld type digital engine tachometer to be designed for dedicated r/min measurement of 4-cycle diesel engines. R/min direct reading measurement is available only by clamping a CP-044 Diesel Engine Rotation Sensor (sold separately) to a fuel injection pipe.Both analog (switchable between analog and monitor output) and pulse outputs are provided; enabling to use analog output for data recording (monitor output for sensor waveform checking or analysis input signal of FFT analyzer), and to use pulse output for tracking analysis signal of FFT analyzer.
-
Product
Diesel Compression Tester
34700
-
Measures cylinder pressure on diesels equipped cars and trucks. Records maximum pressure reached during engine test. Release valve allows for immediate venting and resets gage for repeat tests. Swivel end quick coupler is connected to adapters sold separately. High pressure hose is 16 1/2" long. Gage is scaled from 0-1,000 PSI and 0-70 BAR.
-
Product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
-
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
Product
Gasoline and Diesel Analyzer
NAX-100S
-
Napco Precision Instruments Co
NAX-100S is the X-ray fluorescence spectrometer which is collaborative researched Sense and the University of Michigan in USA,TsingHua University in china and other spectrum experts, It is based on American high-end technology,has a design patent about the unique vacuum system ,special optics path system,designed for the detection of gasoline and diesel,has excellent stability about the ultra low content of elements analysis for petroleum chemical industry products.
-
Product
Biodiesel In Diesel Analyzer
InfraCal 2 ATR-B
-
The InfraCal 2 Biodiesel Blend Analyzer for measuring percent biodiesel in diesel is the ideal solution where a quick, accurate, on-site measurement is required and a single, repetitive biodiesel blend analysis is needed. The InfraCal 2 ATR-B is based on proven IR technology, originally developed by Wilks, and used by fuel distributors, blenders, producers and regulatory agencies worldwide. The compact, easy-to-use Biodiesel Blend Analyzer has a measurement range of 0 – 100% biodiesel in diesel. These results are comparable to both ASTM D7371 and EN 14078, laboratory methods that require expensive FTIR Spectrometers.
-
Product
Diesel Tester Adaptor for Ford 6.0L
35650
-
Has 14mm-1.25 threads for testing at glow plug port. Applications include: Ford/Navistar Power Stroke 6.0L & 6.4L engines found on F-250 through F-550 trucks and International VT 365.
-
Product
VLT Chassis Dynamometers for Diesel Smoke Testing under Road Conditions (CDST)
-
Diesel Smoke Testing by Free Acceleration Test is one! But how accurate is this Test? We all know that it is a not valuable test, but still better as none testing of Vehicle Diesel Engines. The results are not realistic in many cases. And not as good for the Engine we know.
-
Product
Heavy Duty Diesel Compression Tester
DCT1570
-
Compression tester and adapters to test many vehicles, trucks, heavy-duty equipment. Covers Cummins, VW, Volvo, Allis-Chalmers, Bedford, I.I.Case, John Deer, IH, Mack, Massey-Ferguson, Mitsu-Fuso, Scania, White Farm, Detroit Diesel, and more.
-
Product
Combination Exhaust Tester for Petrol- and Diesel- Powered Vehicles with Innovative Condensate Separation
MET 6.3 | VP 135213
-
Maschinenbau Haldenwang GmbH & Co. KG.
The combination tester is designed for the measurement of petrol- and diesel-powered vehicles. The MET 6.3 stands out for its innovative condensate separation thanks to an active water separator. In addition, low weight, compact design and short warm-up time ensure easy handling. Part of the equipment is a 2 m (optional 4 m) long probe for both engine types.
-
Product
Diesel Return Flow Sensor
TP-RFS400
-
Common Rail Diesel injection systems are becoming more and more advanced. The diesel return flow sensor RFS400 can be used together with a lab scope (automotive oscilloscope) to diagnose the most advanced Diesel injection systems.
-
Product
DIESEL COMPRESSION ADAPTER FOR FORD AND INTERNATIONAL
DTC1524
-
*M14 x 1.25 thread adapter attached to hose and a quick disconnect*Screws into the head of the engine in the glow plug hole*Use on International VT 365 engine used in the International 4200 medium-duty truck and Ford Powerstroke 6.0L used in the Ford F250-F550 trucks
-
Product
Opacimeter on Trolley for the Measurement of Diesel Vehicles
MO T | VP 135044
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MAHA Opacimeter on trolley is used for the measurement of diesel vehicles. The smoke opacity is tested and diagnosed in a time-saving and trouble-free manner in a partial flow procedure during free acceleration or under load of the engine. Rapid readiness for measurement and precise measurement results are the distinguishing features of the MAHA Opacimeter. Type-tested according to PTB requirements 18.09.
-
Product
Exhaust Gas Measurement Modules
-
Reliable and precise acquisition of exhaust values: For exhaust gas measurements, i.e. Lambda, O2, NOx, and NH3 in vehicles with petrol, diesel, CNG or LPG engines CSM has expanded its product portfolio with the CAN-based exhaust gas measurement modules from ECM.
-
Product
AC Engine Dynamometers
-
AC dynamometers (dynos) provide accurate and repeatable dynamometer control under stringent operating conditions for various testing applications. Whether testing small electric tools, large electric motors, off-road diesel engines, marine diesel engines or powertrain components, we have a system that’s right for you.
-
Product
COMMON RAIL Electronic Diesel Injection Analyzer
EDIA-PRO
-
The EDIA-PRO is an enhanced version of the proven EDIA-5 analyzer. To meet expectations of our customers we created a system for automatic evaluation of injection system parameters based on measured waveforms. This makes the diagnosis easier and faster. Additional possibility of fast evaluation of cylinder compression and ability to check starting performance along with control valve measurement mode are perfect complement to diagnostic capabilities of EDIA device.
-
Product
Reciprocating Engines
-
GE’s gas engines range in power from 0.12 to 9.5 MWe. Our Jenbacher and Waukesha engines are recognized the world over for their performance and reliability, and our new diesel generator set delivers unmatched fuel efficiency, extended preventative maintenance intervals, the longest overhaul intervals and the longest design life available for high-speed diesel engines.
-
Product
Engine Vibration detector
VP-201/202/1210/1220
-
The VP-201/202 and VP-1210/1220 are electro-dynamic vibration detectors designed for gasoline and diesel engine measurement. By mounting them on the cylinder head or an engine etc, they detect rotation vibration at the time of combustion. It is easy to use due to a small, light weight, and magnetic mounting by means of a built-in magnet on the bottom surface. The detector and the cable are reliable with heat-resistant structure so you can use it in an engine room.
-
Product
Electronic Air Throttle Tester
DTA-1
-
Throttle is usually associated with petrol engines. However, throttle valves are also found in modern diesel engines. They are used under different names, often general and not linking to intake system.
-
Product
Diesel Smoke Analyser
VLT-E9200
-
The VLT-E9200 diesel smoke analyser measures the opacity of the exhaust gases of vehicles with diesel engines. It can measure if an engine comkplies with the EURO 6 standards. An oil temperature sensor and an rpm counter can be connected.
-
Product
Water Brake Chassis Dynamometers
-
Chassis water brake dynos (also known as hydraulic dynamometers) can be operated continuously to resolve overheating, fuel mileage and drivetrain issues. Taylor’s eight models accommodating 50 to 1,100 hp at 40 mph enable testing of single-axle diesel pickup trucks, RVs and buses up through the largest tandem-axle on-highway trucks and buses. Tap into our deep product and applications knowledge to help you choose and make the most of the right water brake system for current and future needs.
-
Product
Diesel and Gasoline Engine Tachometer
TA303
-
The TA303 Smartach is a tachometer designed for use on any engine equipped with an alternator, and only requires a simple connection to the electrical system (e.g. battery, alternator, cigarette lighter connector) to measure engine RPM. Taking advantage of the ripples generated by the alternator, the TA303 automatically calculates the relationship between the speed of the engine and the alternator ripples, and uses them to measure RPM on any piston engine regardless of its ignition system (Diesel or gasoline).
-
Product
Multi-Stage Injection Analyzer
FJ-8000 series
-
Common rail method already is commonly known as an injection system of diesel engine now. That system enables multi-stage fuel injection by offering high injection pressure in various driving situation. Adopting the common rail system helps improving fuel consumption, reducing noise and vibration, because the system can make the fuel approximate complete combustion which suppresses PM and NOx generation. FJ-8000 series is the multi-stage injection analyzer that supports more accurate injection by measuring injection quantity, injection rate, injection timing, and injection period by multi-stage injection of common rail system in the environment that is near to an actual vehicle environment.
-
Product
Radiator Mounted Load Banks
RD-Series
-
RD-series radiator mounted load banks are designed to be fitted directly onto diesel generator sets. RD-series load banks use the engine cooling air from the generator radiator to cool the load elements.
-
Product
DEF Refractometer - Urea Scale
DEF-201
-
The MISCO DEF-201 digital refractometer is the ideal method for testing and monitoring the concentration of urea-based Diesel Exhaust Fluid (DEF or AdBlue) required by diesel engines equipped with Selective Catalytic Reduction (SCR) technology. This refractometer has a single scale for DEF concentration.
-
Product
2WD Dynamometers
MD-500-SE XL
-
The 500 series dynamometer has a larger big brother – the MD-500-SE XL! The 500-SE is an excellent 2WD performance dynamometer and the XL model expands on these traits by adding in a much wider 98-inch outer track and a HUGE mechanical flywheel to increase the mechanical inertia of the dyno to about 2,000-lbs. This additional inertia helps reduce the duty cycle burden on the eddy current PAU and even allows for pulls to be done in a pinch in inertia-only mode. The XL handles vehicles like diesels and Ford Raptors where the 500 is a bit too narrow for these types of applications. The MD-500 XL’s multiple upgrade paths allows for an AWD upgrade in the future and enables it to accept a second eddy current PAU for increased loading capability. We’ve seen this dyno handle almost 2,000-hp to the wheels on power sweeps so don’t be fooled by the 1,500-hp peak measurement specification. If your tires will hook you can measure as much power as you are laying to the rollers. The large K250 eddy current PAU has plenty of torque for testing and tuning anything from your local diesel pickup crowd and local LS guys to classic carb stuff and front wheel drive cars. The 500-XL is great product at a great price with tons of range. It is also easy to install – buy the aboveground kit with the 16-ft ramps and have this dyno set up and ready to roll in your shop in a half a day! if you want to know more call us! We are always happy to answer questions.
-
Product
AC Load Banks
K-1000 Series
-
Kongter Test & Measurement Co., Limited
Load bank testing is vital to replicate and verify the operation of critical backup power systems such as diesel generators and uninterruptible power supplies (UPS). Kongter offers a wide range of customer-tailored AC load banks that excel in a range of load test applications and environments.
-
Product
Emission Analyzers
-
The VLT-E8104 emission analyser measures the opacity of the exhaust gases of vehicles with petrol/LPG/CNG engines. The accuracy complies with OIML class 0. An oil temperature sensor and an rpm counter can be connected.If you connect diesel smoke cell VLT-E9210, this analyser is a fully functionsl diesel smoke analyser as well.
-
Product
Dynamometer
I-Series
-
AW I-Series dynamometers are excellent for diesel engine testing as well as other applications. The electronic load control system on this hydraulic activated dynamometer allows for precise and steady control of Power and RPM levels.
-
Product
Emissions Dynamometers
MD-1000-M
-
The MD-1000 sets the industry standard for heavy duty chassis dynamometers due to its rugged design and accurate loading capabilities. Simulate on-highway driving conditions under real world loads. Adjust loading to simulate a host of in-use operating conditions. The 1000 is approved for use in Nevada and Colorado for Diesel Smog Testing.
