-
Product
Protection Test Set
COMPANO 100
-
COMPANO 100 is the universal and easy-to-use solution for all types of basic testing duties in electrical energy systems. Controlled electronic sources allow the user to obtain exactly the desired value and to output signals with variable frequencies and other signal forms, automated ramps, and pure DC.
-
Product
ARINC 818 Tester
-
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
Product
Electronic Control Unit Functional Test
-
End-of-line tests are critical to ensure passenger safety in the era of smarter vehicles. A flexible test solution is needed to ensure extensive test coverage and high test throughput with a low total cost of ownership.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
-
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
Level Test Set
ET 91
-
100 Hz to 2.4 MHz selective/wideband Level Meter & Generator,with Spectrum Analyser and Z/RL/LCL Bridge
-
Product
Programming Accessories
-
A comprehensive range of hardware designed to support their universal and gang programmers.
-
Product
Test & Programming Software
ScanExpress
-
The ScanExpress Family of boundary-scan software offers a fully integrated development environment that includes boundary-scan and at-speed functional test program generation, test program execution with advanced pin level diagnostics, interactive boundary-scan debugging, and in-System Programming (ISP) of devices such as Flash memory, serial EEPROMs, CPLDd, and FPGAs.
-
Product
Test Program Development
-
Today's System-On-Chip-designs require creative development of test system add-ons. Test vector converters for most common simulators are available. Our specification for test program development is available on request. Our specification for test program development is available on request.
-
Product
EMS Test System
TS9982
-
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
Product
EVSE Test Platform
-
To manage both the challenging high-power requirements of electric vehicle supply equipment and the market demand, it is crucial to rely on a test system that performs to your specs. The right system needs to combine the tools for reliable asset communication, microgrid management, effective protocol simulation and high-power testing. This EVSE platform combines the right energy regeneration equipment with 25+ years of test experience to deliver the results you need to meet conformance in the time you need it.
-
Product
Automatic Relay Test Set
MT2000 Series
-
Portable single phase dual current manual and automatic relay test set. Readymade test modules. Independent control of Phase angle, frequency and amplitude.
-
Product
Bench Top Test Set
WesTest-3000/BTTS
-
Communications & Power Industries
*PXI Based*Test Requirements Driven*Cost Capability Consistency*Software Standards- ATML, IEEE
-
Product
4-Module ICT System, I307x Series 6
E9903G
-
Test efficiency, test system stability, and seamless equipment integration. Keysight’s i3070 Series 6 family provides those improvements built upon a proven technology foundation. With time-tested software, hardware, and programmability, the Series 6 are fully backward compatible with previous systems, and they make highly repeatable measurements.
-
Product
EFT Module for Teststand
-
The Electronics Functional Test (EFT) Module for TestStand provides out-of-the-box tools to speed up development of automated tests for electronic assemblies including PCBAs, subassemblies and final assemblies. Test engineers can develop, deploy and execute test sequences quickly and efficiently with minimal custom code development for a shorter time-to-solution.
-
-
Product
Lower-Cost Small Footprint In-Circuit Test System
TestStation LHS
-
The TestStation LHS in-circuit test system is a lower-cost, small footprint, feature scalable version of Teradyne’s popular, award winning TestStation product family. Compatible with existing TestStation LH fixtures.TestStation LH features the voltage accuracy and backdrive current measurement embedded in Teradyne’s SafeTest protection technology for accurate, reliable and safe powered-up testing of new low-voltage software.
-
Product
Test Set For Instrument Transformer
-
This modern Test Set For Instrument Transformer is used for measuring relative errors of Instrument Voltage and Current Transformers. This is developed for reading out the unbalance of any bridge circuit. It also calculates the burden associated to the test sample. In addition to this, it further converts it to ratio and phase error values for presenting them on a LCD screen. With high-tech microprocessor controller, it ensures to provide quick and correct measurements.
-
Product
ATE Self Test Fixtures
AL663
-
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
Product
Aircraft Test Set
CA-2100S-07
-
The CA-2100S-07 is a bench mounted, modularized and computer based test set used to service all types of aircraft electronics. It simulates the aircraft environment and replaces a myriad of specialized test fixtures found in the industry.
-
Product
Service Ground Test Set
900
-
TESCO’s Service Ground Test Set has been designed to check the condition of the ground connection on a secondary service. If for any reason the ground connection has a resistance, this can be immediately detected by the Test Set. The Service Ground Test Set consists of a voltmeter which can be shunted by a resistance of 60 ohms. The voltmeter is of the suppressed zero type with a double range, from 65 to 130 or from 130 to 260, and can be used for checking service voltage independently of the ground test.
-
Product
Universal Launcher Test Set
TS-217
-
The TS-217 is an I-level and Depot-level Universal Launcher test set supporting fighter aircraft launchers including the LAU-127, LAU-128, and LAU-129 (AMRAAM), LAU-117 and LAU-88 (Maverick), and LAU-7 (Sidewinder) missile launchers, launcher electronic assemblies, launcher power supplies, and circuit cards. The TS-217 is also used as a depot-level tester for F-18 armament including launchers (LAU-127, LAU-7, LAU-115, and LAU-116), bomb racks (BRU-32), and aircraft pylons (SUU-62 and SUU-63). Additionally, the TS-217 supports MAU-169 Paveway kits, subassemblies, and circuit cards. The TS-217 performs full parametric functional testing as well as troubleshooting to the faulty LRU (I-Level configuration) and SRU (Depot-Level configuration). The TS-217 can be used as an I-Level tester or as a Depot / Acceptance tester for launcher subassemblies.
-
Product
Bench Top Test Set
WesTest-3000/BTTS
-
WesTest Engineering Corporation
*PXI Based*Test Requirement Driven*Core Capability Consistency*Software Standards- ATML, IEEE
-
Product
Flash Programming for Functional Test Systems
-
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
Product
Memory Test Systems
T5503HS2
-
Semiconductor memories are in high demand to meet the needs of fast-growing end markets such as portable electronics and servers. It has been forecasted that applications ranging from mobile devices and data centers to automobiles, gaming systems and graphics cards will consume an estimated 120 billion gigabits of DRAM capacity. To meet this market demand, new generations of memories with data-transfer speeds of 6.4 Gbps and higher are being developed. Advantest’s second-generation T5503HS2 tester is designed to handle these ultra-high-speed memory ICs.
-
Product
TWT Test Set
-
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process. Polarity designed and developed this Microwave Tube Test Set with the following specifications:
-
Product
AC Hipot Test Set
-
Weshine Electric Manufacturing Co., Ltd
AC Hipot Test Equipment for Dielectric Withstand Test are suitable for 50 / 60 Hz AC testing of low capacity test objects. Optionally, these units can also be upgraded to function as DC test sets by mounting the rectifier attachment on top of the transformer.Weshine® AC Hipot Test Set for AC hipot test can be equipped with a rectifier attachment for DC voltage testing.Typical application areas:Testing of cables Testing of switchgearTesting of transformersTesting of CP & PTTesting of MV systems
-
Product
Test Fixtures & Test Sets
-
Keysight test fixtures are used to hold electronic components or materials (physically and electrically) in order to perform various measurements. Keysight offers a variety of test fixtures from Parametric, Dialectrice, Liquid test fixtures and more.Some of our test fixtures allow you to connect directly to your measurement instrument, while others require various adapters.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
Seven-Module Test Set
F8300
-
Use the F8300 for testing three-phase conventional schemes and digital protection systems. This seven-module F8000-series instrument is available in five standard configurations of HVA Current, HVA Voltage, and Low-Density Logic I/O modules.
-
Product
Boundary-Scan Test / In-System Programming Controller
CPXI-1149.1/Turbo
-
The CPXI-1149.1/Turbo is a high-performance boundary-scan controller for multi-TAP (Test Access Port) and concurrent JTAG test and in-system programming. When combined with a ScanTAP™ intelligent pod, the CPXI-1149.1/Turbo offers up to 80 MHz clock rates on 4, 8, or 32 TAPs with features such as external write strobe, direct programming, and analog voltage measurement.
