Motion Simulation
-
Product
6 Channel Function Generator / Flow Simulator
DP-cPCI-2601
-
DP-cPCI-2601 is a 6 Channel 2MS/s Waveform Generator with high frequency performance, versatility and compact size in an economical cPCI bus format. Signal output in the range of 10 mHz to 5 KHz with 14 bit vertical resolution makes this single slot, 6U-sized cPCI card a powerful solution to meet most demanding test stimulus.DP-cPCI-2601 uses Direct Digital Synthesis (DDS) technique to generate stable and accurate output waveforms down to 0.01 Hz resolution. DP-cPCI-2601 offers Sine, Square, Ramp, Triangle, Pulse as built-in wave shapes and user defined arbitrary waveform.DP-cPCI-2601 can frequency sweep any of its function outputs. User can sweep upwards using linear sweeps.
-
Product
Spacecraft Power Bus Simulator
-
AMETEK Programmable Power, Inc.
*Provides enhanced measurement and data-logging of up to 40 channels.*Bus Power Monitoring Unit (BPMU) can be easily relocated to TVAC chamber to ease cabling complications*Data can be viewed either in spreadsheet or graphical format*Spacecraft (Payload) Protection Unit (SPU) provides 10 μsec reaction to out-of-tolerance conditions g
-
Product
Electrostatic Discharge Simulator
ESD61000-2
-
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD61000-2/ESD61000-2A has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
Product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
-
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
Product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
-
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
Battery Simulator
-
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
Product
Ethernet Test and Simulation Instruments for Speeds from 10 Mbit/s to 25 Gbit/s
-
Avionics Interface Technologies
AIT’s Ethernet test instruments provide Ethernet test features for 10Mbit, 100Mbit, 1Gbit, and 10Gbit Ethernet networks, for both Optical and Copper media. All instruments are supported by Analyzer and Simulator software applications (GUIs) and additionally software API’s allowing integration into user applications.
-
Product
Modbus Test & Simulation Software
ModBus Constructor 1.7
-
Using Modbus Constructor you can quickly create a data management model for any of your Modbus devices. Unlike other available solutions on the market which provide displaying data as columns of abstract numbers of the same type, Modbus Constructor represents each data element exactly as you need. You may define type, format or scale independently. This makes them easy to read and analyze.
-
Product
Collins Radar Fixture with Gyro Simulator
TA-3A/B
-
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
-
Product
ESD Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
Product
O-RU Simulator
-
With Simnovus’s web interface, there is no need to install any software to use the UE simulator.The UE simulator has an intuitive step-by-step workflow to walk users through the generation of even the most complex test profiles in just a few minutes.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x-DS
-
A unique feature of AIM’s APE1553-x-DS modules is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
Xenon Long Pulse Solar Simulator Three Target Sizes
-
Complies with IEC60904 Class A solar simulation standards.Up to 100ms of effective irradiated time is achieved. Through our proprietary filter technology, spectral concordance conforms to IEC / JIS Class A standards.Three systems provide a wide selection to meet your panel size, floor space, and performance requirements.
-
Product
Molding Simulation Software
Moldflow®
-
Engineers and analysts use Moldflow software for plastic injection molding simulation to improve plastic part designs, injection mold designs, and manufacturing processes.
-
Product
4 Port Phone Line Simulator (FXS) Adv
SIM-4FXS-A
-
This unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, modems, access servers, audio conference equipment or anything that requires phone lines. Telephone line simulator acts like a "telephone company in a box" providing dial tone, ring voltage and all advanced phone line features such Caller ID, Call Waiting, Call Hold, Three Way Calling and many others.
-
Product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
Product
2 PRI + 32 BRI-S/T ISDN Simulator
CH-32BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 32 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
Distributed Motion Control
-
ADLINK's Intelligent Remote Data Acquisition & Control Modules (NuDAM) are designed for data acquisition systems based on PCs and other processor based equipment with standard serial I/O ports (RS-232 or RS-485 with auto direction control).The modules convert input/output signals to engineering units and transmit/receive, in ASCII format, to/from any host computer with an RS-232 or RS-485 port. NuDAM modules are the key components in flexible and cost effective remote data acquisition and control systems.
-
Product
Vehicle Network Simulator
OBD Simulator™
-
Simulate Vehicle Network Messaging for OBD CAN, J1939 CAN, J1850 VPW, J1850 PWM, ISO-9141 and KW2000.
-
Product
Motion Control Terminal Board for Mitsubishi J2S-A Servo Amplifiers
DIN-814M0
Amplifier
This well-designed motion control terminal board is for the users who use Mitsubishi J2 super servo. With this terminal board, users can ealisy complete wiring with PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134.
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P | VP 230046
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P is also suitable for power measurements at constant speed and constant tractive force.
-
Product
Uphole Simulator
-
For testing Boom Boxes and other Blasters. The Uphole Simulator is the tool for testing a dynamite blaster in the shop or field. Quick and easy, the UHS unit connects to the high voltage output of the blaster and the uphole geophone input.The UHS sinks the output voltage from the blaster. As it receives the charge, it counts down 30 milliseconds and then outputs a waveform, simulating the signal the blaster might receive from an actual geophone.
-
Product
LED DC Electronic Load Simulator
3340G Series（150W~300W）
-
Each 3340G Series module has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, plug in 3300F with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
-
Product
Engine Torque Pulse Simulation
ETPS
-
HORIBA has revolutionized the way vehicle manufacturers test their Powertrains and Front End Accessory Devices. The ETPS dynamometer system accurately produces torsional pulse characteristics of an engine. This new technology employs a sophisticated mathematical model to calculate the resulting torque at the output of the engine based on engine and combustion process parameters.
-
Product
Solar Simulator
-
It is an LED light source for evaluating the performance of organic solar cells in indoor light applications.A neutral white LED light source equivalent to a color temperature of 5000 K, achieving an effective irradiation area of 50 × 50 mm.The illuminance can be changed without changing the height of the light emitting surface with low illuminance (200 lx) and high illuminance (1000 lx).
-
Product
Single Or Dual Stream MIL-STD-1553 A/B &4, 8 Or 12 Channel ARINC429 Mixed ProtocolTest & Simulation Module For Standard Ethernet
ANET-MxAy
-
Single or dual stream MIL-STD-1553 A/B and 4, 8 or 12 channel ARINC429 mixed protocol Test & Simulation module for standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create runtime applications (e.g. MIL-STD-1553 to Ethernet Converter / ARINC429 to Ethernet Converter , MIL-STD-1553 to Ethernet Gateway / ARINC429 to Ethernet Gateway) to execute right in the box. For wireless applications an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET docking station to host up to 4 ANET modules.
-
Product
Solar Simulation Systems
-
Solar simulation systems with global radiation guarantee the simulation of natural sunlight according to CIE20 and CIE85 Table 4. Our portfolio includes components, systems and systems for solar simulation for test benches in the automotive, military, aerospace, railway, photovoltaic, material research and building materials industries. Our plants and systems stand for high reproducibility and precise test results.
-
Product
8 CHANNELS ARINC 429 Simulator Analyzer Tester
CIC429
-
The CIC429 is a full featured, high performance Serial bus Simulator Analyzer Tester developed by Andor Design for test and simulation of ARINC 429 or similar Avionic buses. The CIC429 is designed as a 5/8 size plug-in card for an ISA bus. An on board microprocessor off loads the host by organizing the data in a predefined structure in the dual port RAM. Programming the CIC429 consists of changing this data, which can be done on the fly for real time applications
-
Product
Oxygen Sensor Tester and Simulator
ST05
-
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
