Test System Integrators
-
Product
Precision Multiferroic and Ferroelectric Test System
-
The Precision Multiferroic tester is Radiant's most advanced test system. The Multiferroic has fast built-in frequency at 30kHz measurements using the 200V internal amplifier and 50kHz measurements using the 100V internal amplifier. This system comes in a built-in option of +/-100V, 200V, and 500V and can be expanded to 10kV. This unit also comes with a 18 bit ADC and requires no configuration changes.
-
Product
Test Program Execution for High-Volume Production Systems
ScanExpress Runner Gang
-
Electronic manufacturing test systems must be fast and efficient. Schedules today are shorter, products are more complex, and the market demands higher speed—the product needs to be built and shipped yesterday.ScanExpress Runner Gang Edition is a concurrent boundary-scan and in-system programming test executive designed specifically for high volume production. Unlike traditional test systems which execute sequentially on a single unit under test (UUT) at a time, ScanExpress Runner Gang Edition provides concurrent (gang) testing on up to 8 UUTs for improved test and programming times.
-
Product
End of Line Noise Test System
-
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Product
16 Channel Charge Integrating ADC
CQ16
-
The CQ16 is a 16-channel 12bit, fast converting charge-integrating ADC for CAMAC. To provide compatibility to older CAMAC ADC’s it can be switched into an 11-bit mode. All data read-out is provided either via CAMAC commands or through the fast FERA bus on the front of the module.
-
Product
Electric Motor Test Systems
-
Electric Motor Test Systems feature our highly successful water brake dynamometer which is used as an electric motor loading device.
-
Product
System Tests Radar Pulse Stability
PN9002
-
Noise eXtended Technologies S.A.S.
The cost-effective PN9002 test simplifies the testing and analysis of pulse-to-pulse amplitude and phase stability for radar systems and components to 18GHz.
-
Product
Vibration Testing System
-
Torontech is now offering Vibration Test Systems, Shock Test Systems, Bump Test Systems, Drop Tester, and Packaging Transportation Simulators.
-
Product
FPD Tester Model
27014
Test Platform
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
-
Product
Testing
-
Apogee Labs offers a wide variety of modular chassis types used for test applications with various Data Link Test Modules.
-
Product
Gated Integrator, 2 ns Minimum Gate Width
SR250
-
Stanford Research Systems, Inc.
The SR250 Gated Integrator is a versatile, high-speed, NIM module designed to recover fast analog signals from noisy backgrounds
-
Product
Wireless Crane Systems & Crane Systems
-
Ningbo Yaheng Electronic Technology Co.,Ltd
YEAHEVER Wireless Crane Systems & Crane Systems
-
Product
Motor Stator Test System
Chroma 1920
-
Chroma Systems Solutions, Inc.
For electrical safety and quality testing functions of motor stator coils
-
Product
Laser Diode Reliability Burn-In / Life-Test System
58602
Test System
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
Product
Portable Test System
MT781
-
Actual value, vector, curve displayCurrent and voltage generationerror measurementMeasurement of harmonics up to the 40th
-
Product
High Voltage Test System
CKT1175-15
-
12.5 mV – 2000 VDCIR measurements to 5000 megohmsHipot testingDwell time prog. from 1 ms to 1000s in 1 ms steps
-
Product
Adapter Interface 0-19Slot | Test System LH
101153
-
Interface 19 Slot | 256 Pin CardSlot | Pin countGenrad 8x 128 PinInterface 0-19 Slot | 2048 D/S
-
Product
Radio System
FASST
-
Futaba is the first of the traditional radio manufacturers to bring the advantages of 2.4GHz spread spectrum technology to modelers – and the first to introduce that technology in a full-range aircraft system. For getting the full benefits of 2.4GHz technology, you'll find that Futaba's experience makes all the difference.
-
Product
RSP-2T Test System Interface Probe
RSP-2T
ICT/FCT Probe
Current Rating (Amps): 5Average Probe Resistance (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 167Full Travel (mm): 4.24Recommended Travel (mil): 79Recommended Travel (mm): 2.00
-
Product
Burn-In System
-
The COBIS-II Series Burn-in System is designed to test the latest high frequency integrated circuits (ICs) and combines a large capacity oven with well proven Accutron FlexBID™ dynamic driver technology. This system is engineered for productive dynamic device testing and reliable monitoring.
-
Product
Systems
-
Datum Electronics Systems - Silo Hawk silo weighing system, Datum Hawk engine condition monitoring system, Cargo Hawk SOLAS compliant container weight verification system, and more
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
Test Automation System for Heavy-Duty Engine Emission Testing
STARS HDEET
-
STARS HDEET is a Heavy-Duty Engine Emission Test application available as an optional extension to STARS Automation. It provides efficient test cycle execution, emissions equipment control, results calculation and reporting, in compliance with the different legislative standards. Its flexible design offers a wide range of customization while addressing the various requirements for research and development, conformity of production, and certification testing.
-
Product
Optics Test Systems
Lens Test
-
Optik Elektronik Gerätetechnik GmbH
LensTest enables the measurement of air gaps, lens thickness, lens radii and lens surface centration errors in mounted lenses as well as the active alignment of lens surfaces during optics assembly for centering without rotating the assembly.
-
Product
CT/VT Test System
-
Fully pre-wired comprehensive turn test system. *Suitable for CTs up to 6000A & VTs up to 132kV. * Precision to (0.005 class) internal multi-ratio standard CT. * Internal 4KA current source. * State-of-the-art Instrument Transformer Test Set AITTS-98 with computer & printer interfaces. * Electronic potential divider facilitates testing any VT ratio upto 132kV. * Current & potential burdens.
-
-
Product
Electrical Test System TY-CHECKER
DG Series
-
Experience high-speed testing and short tact timers!
-
Product
ESM/ELINT System
-
Shoghi’s Electronic Support Measures (ESM) are designed for electronic warfare techniques involving actions to detect, intercept, identify, locate, record, and/or analyze sources of radiated electromagnetic energy for the purposes of immediate threat recognition.
-
Product
Wireless Test System
WTS-80
-
CETECOM offers a wide range of services and solutions to help companies develop and execute product testing plans to determine a product’s compliance status and master the increasingly complex regulatory issues of the internationalmarket.
-
Product
Material Compatibility Test System (MCTS)
-
Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:
-
Product
Multi-DUT Mobile & IoT Test System
IQxstream-M
-
Its ultra-compact design and flexible architecture makes it highly suitable for high volume manufacturing of smartphones, tablets and cellular IoT modules.
