Dynamic Engineering
Dynamic Engineering products are designed and manufactured in the USA. The majority of assembly work is done in our state-of-the-art manufacturing facility in California. Since 1988 we have developed engineering, purchasing, assembly, and test capabilities to guarantee reliability in our products. This is evidenced by our AS9100 and ISO9001 certifications. Dynamic Engineering has a wide product line with embedded solutions for PCIe, PCI, PMC, XMC, IndustryPack, cPCI, cPCIe, PCI-104, PC104e, VME and VPX. We also work with custom requirements. Solutions include adapters/carriers to install one embedded format [i.e. PMC] into another [i.e. PCIe], utilizing available positions in current systems with existing or upgraded hardware. Other solutions include standard bus interfaces for example: SpaceWire, 1553, and HOTLink. Custom designs are frequently implemented for special purpose buses and interfaces. Additionally, Dynamic Engineering provides chassis, power supplies, backplanes, breakouts, cables and other support functions to complete each solution. Drivers, reference SW and applications are supported for Windows, and Linux. For information on specific products please visit our website
- 831 457 8891
- sales@dyneng.com
- 150 Dubois St.
Suite B&C
Santa Cruz, CA 95060
United States of America
-
Product
IP-Reflective Memory
-
Each IP-ReflectiveMemory can be used as a standard node or as the Master Node. Clearly labled "DIP Switches" are provided to make the selection of Master or Standard Node, and the Node Address. The Network is based on using LVDS signaling over Ethernet cabling. Nodes automatically come up for pass through operation.
-
Product
Compact PCI Connector Board
cPCI-J2-SCSI
-
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
Product
8 Channel Serial IndustyPack Card
IP-OctalSerial
-
8 channel serial IndustyPack card with 4 dedicated in and 4 dedicated out channels. Each channel has its own seperate FIFO and state machine
-
Product
PCIe and VPX Compatible Adapter Carrier
PCIe2VPX3UX4
-
The power supply designs utilize switching regulators controlling MOSFET´s. An LC filter insures clean power at the VPX device. The PCIe gold fingers are rated for 1.1A each, and a total of 5.5A on the +12V rail. 55W are available to the card after power conversion.
-
Product
PCI-104 Adapter for PMC
PC104p2PMC
-
PC104p2PMC ( PCI-104 to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI-104 slot. Suitable for PCI operation with 32 bit data and 33 or 66 MHz bus operation.
-
Product
PCIe-SpaceWire
-
PCIe-SpaceWire implements SpaceWire in a convenient PCIe format. Four fully independent and highly programmable LVDS IO ports are provided by the PCIe-SpaceWire design. The SpaceWire protocol is advanced with link testing, error handling, command and data protocols built in. The SpaceWire electrical interface is point-to-point with token based flow control. Now with DDR memory for 32 Mbytes per port [256 MB total]
-
Product
IP-QuadUART-485
-
The IndustryPack compatible IP-QuadUART-485 design integrates a quad UART onto an IndustryPack module. The UART (16C854) features 128 byte FIFOs for RX and TX ports on each channel. The UART is supported by an advanced IP module interface implemented within a Xilinx FPGA.
-
Product
PMC Carrier with 2 Positions
PMC-MC-X2-28
-
PMC-MC-X2 adapter/carrier/motherboard provides the ability to install up to 2 (two) PMC cards into a small enclosure. PMC-MC-X2 has one PMC card mounted front and one rear to create a compact arrangement with 2 PMC positions. The carrier provides power supplies for the +5, +3.3, +12, and minus 12 from a reference supply.
-
Product
PCIe Adapter for VPX
PCIe8LSwVPX3U
-
PCIe8LSwVPX3U is an 8 lane PCIe adapter with switch isolation for VPX development. The switch isolates the spread spectrum clocking found in most PC´s from the VPX port. PCIe 3.0 compliant, 1-8 lanes can be used by the installed VPX.
-
Product
IP-Parallel-BA1 "IP-Tape"
-
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
Product
Cable Assembly Crypto / Tape
-
The Cable Assembly Crypto / Tape provides a method of interconnecting the IP-Crypto and IP-Tape from the carrier to the PCI Bezel [rear IO] when installed into a PCI machine. Most IP Carriers have 50 pin headers suitable for ribbon cable in use for the IP Module IO. The headers are located on the carrier and internal to the chassis. Interconnecting to the outside world can be an issue.
-
Product
Multi-Functional Board
PCI - HARPOON
-
PCI-Harpoon is a multi-functional board with capabilites for isolated measurement and control. The initial use of the PCI-Harpoon is to simulate - act as if the PCI-Harpoon was another piece of equipment. The simulation provides a means to test the rest of the equipment without requiring the real [expensive] asset. In addition the PCI-Harpoon can provide status and direct software control of the system.
