Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +44 (0)161 371 6000
- +44 (0)161 371 6010
- Edge Lane
Manchester, England M43 6BU
United Kingdom of Great Britain and Northern Ireland
-
Product
Compact Balance
8720
-
The Elcometer 8720 Compact Balance is very easy to use and offers extensive weighing functions selectable by the user.
-
Product
Elcometer Bresle Test Patches
135C
-
The Elcometer 135C Bresle Test Patches determines the concentration of soluble salts on uncoated surfaces in accordance with the ISO 8502-6 test method.
-
Product
ISO Viscosity Flow Cups
2353
-
The Elcometer 2353 ISO Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
Product
Pinhole & Porosity
-
Premature corrosion of a substrate is usually due to a coating failure. A major cause is the presence of flaws in the finished coating. Collectively referred to as porosity, the main types of flaws are:
-
Product
Elcometer MarSurf PS10 Surface Roughness Tester
7062
-
In protective coating applications there is a requirement to measure surface roughness. With 31 surface parameter settings available the Elcometer 7062 surface roughness tester can display all parameters that comply to National & International Standards.These values include peak-to-valley profile measurement in combination with an assessment of the frequency of peaks within the sample area.The Elcometer 7062 surface roughess tester is a light weight and portable measuring solution for the range of surface roughness measurements required for compliance to International Standards.The unit is also suitable for assessing surface roughness conditions in a wide range of general industrial applications; particularly where the sample is too large to bring to the laboratory.
-
Product
Dust Tape Test Kit
142 ISO 8502-3
-
Used in conjunction with the Elcometer 145 Dust Tape Roller the kit can be used in accordance with the recommendations of BS EN ISO 8502-3 either as a pass/fail test or as a permanent record of the presence of dust. Supplied in a carry case for use in the field to assess surface cleanliness.
-
Product
Film Application & Test Charts
-
For numerous products, such as paint, ink, varnishes, glue and cosmetics, the reliability of many laboratory tests is directly related to the quality and consistency of the samples. Any measurements made on coatings for the purpose of describing their physical properties (drying time, elasticity, abrasion, gloss, colour, shade, etc.) are made on the basis of uniform and comparable samples with precisely controlled thickness.
-
Product
Surface Profile
-
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
Product
Protective Coating Inspection Kit 3
-
Measurement parameters include:Surface profileSurface temperatureClimatic conditionsCoating thicknessAdhesion
-
Product
Covermeter & Half-Cell Meters
-
A covermeter, or rebar locator, is a gauge that measures the thickness of concrete cover over steel reinforcement bars and metal pipes. The covermeter can tell you the depth of the rebar, the location and orientation of reinforcement bar (rebar) and determine the diameter of the rebar.
-
Product
Cross Hatch Adhesion Tester
1542
-
The Elcometer 1542 Cross Hatch Adhesion Tester is ideal for measuring the cross hatch adhesion of coatings up to 250µm (9.8mils) on flat surfaces and test panels.
-
Product
Taber® Linear Abraser (230V/115V, 50/60Hz)
5750
-
Whatever your product, be it curved, round, big or small, the Linear Abraser from Taber® can test it all.
-
Product
Calibration Foils Sets
990
-
The Elcometer 990 Calibration Foil Sets are ideal for use in the laboratory, on the production line or on site.
-
Product
Probe Placement JIG
456 & 355
-
The Elcometer Probe Placement Jig is the ideal accessory for measuring coatings on small or complex components when the highest levels of repeatability and accuracy are required.
-
Product
Climate, Dewpoint & Relative Humidity
-
Monitoring climatic conditions, such as temperature, relative humidity, dewpoint and moisture, is often vital to the successful application of a coating and are critical to the resulting quality and performance of the coated product.
