6TL Engineering
6TL is a pioneer in applying the modularity concept to the design of Automated Test Equipment for electronics products. FastATE® Technology is the core to developing turn-key solutions that are truly modular, scalable and flexible, and thus we help to make the job of both test engineers and budget managers much easier. Thanks to FastATE, test engineers do not have to address the recurrent tasks of every project: a 6TL module completes these tasks for them. Each module selected is a high-level block that covers a function of the ATE and works together with the rest making in the end a real modular and flexible production test solution. The resulting test solution will be easily documented and will smoothly become the standard for the production, since the standardization is in the genetics of the FastATE® Technology.
- 34 937 270 074
- info@6tlengineering.com
- PASSATGE DE LA NOGUERA, 2
CASTELLAR DE LAS VALLES, BARCELONA 08211
Spain
-
product
Configurable Reostat or Potentiometer Module
YAV90084A
4x 8-Bit 1KOhm reostat4x 8-Bit 40 Ohm reostat2x 8-Bit 5 MOhm reostat10x Electronic Potentiometer 8-bit resolution -256 steps- with build-in self test10x Voltage to current source 0(4)..20mA10x Analog Outputs (buffer for voltage or frequency)36-Ch Test Point voltage divider2xCAN Bus Channels Terminators testerExpandable with NI PXI-6723 and PXI-6345.
-
product
6TL-3X INLINE Header Conveyor 765 mm Length
AQ580
- PCB up to 600mm length 400 mm width- Programmable transfer speed up to 1 m/s- Automatic Previous/Next speed adjustment- 2D Code reader w/automatic positioning- Pre-wired for second 2D Code reader- Automatic width setting- PC for line management w/UPS with 20” monitor and keypad in adjustable position arm- 24 Ports PoE Switch- Power inlet rack with current protections and line safety relay- Top cover and door w/safety contacts inhibiting line modules while active- Mechanisms self-test- Width auto-adjustment and cyclic width- Non-contact electronic stop of the PCB- 4U Free on the 19” Rack- Interfaces SMEMA 9851 y IPC-HERMES 9852- CE certified
-
-
product
Off-Line Base Test Platforms
To configure your Base Test Platform, the following parts can be added to the 6TL-19 bare half-rack:– Test Rack Manager, to control the test station.– Power Distribution Unit.– Uninterruptible Power Supply– Industrial PC or NI PXI to control the platform– 19’’ Monitor and keyboard with trackball– VPC Mass Interconnect Receiver (6 or 12 slots)– YAV Modules– Accessories: Beacon, Air inlet Pneumatic kit…– Any 19’ Instrument
-
product
RF Testing Platform for ATx05
AT118
The functional test of modern devices with wireless connectivity always requires RF isolated cameras, as the only way to have the parameters controlled and to guarantee operation under the specified conditions.
-
product
8-Ports Gigabit Ethernet ITA Interface
YAV90058A
8 RJ45 LAN connectors to VPC ITA 192 pins module
-
product
32-Ch SPDT 2A-240VAC 24VDC Switching
YAV90133
32 relays, 5A Switching 5A 250Vac. Up to 1250VA 28 Relays SPST Mux. 1 a 4 relays CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
6TL24 Combinational Base Test Platform
H71002400
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
product
4x (1 to 4) + 1x (4 to 1) 50 Ohm 2.5GHz Mux
YAV91500
5x (1×4) Mux + 2x Pass trough30Vac/dc, 10W MaxMax current 500mACAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs availableReflective
-
product
RJ45 (Ethernet 100 Base T) to 90 Series Interface (R)
J90RJ45R
RJ45 Ethernet connector for VPC Tripaddle 90 series RCV moduleUp to three connectors per moduleFor Cat 5 Fast Ethernet cable IEEE 802.3 standard100 Base-T
-
-
product
12-Ch 10A RCV Power Distribution Unit
AR438
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
product
21-Ch 6A-250VA 2-Bus Fault Insertion
YAV90077
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
-
product
Calibration Kit YAV90MMU
YAVMMUCK
The Calibration Kit includes the tools for YAV90MMU test and calibration. As the YAV90MMU is the core of the YAVPack Bundle (YPB), this calibration kit is also an option for the YPBs.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
-
Columbia Elektronik AB
COLUMBIA ELEKTRONIK AB is an expert organisation delivering complete test fixturing solutions to the Nordic electronics industry. Having pioneered the Swedish, Norwegian, Finnish and Danish markets back in 1977 we have today an absolute leadership in fixturing and test technology and enjoy a solid, major share of the market. We cover the whole spectra with testsystems, testfixtures, mass interconnect solutions and both hardware and software support and services. We design and produce both our own and vendor delivered testfixtures and mass interconnect solutions for functional and in-circuit test of electronic products and assemblies from component and PCB level to subassemblies and finished products. Columbia excels in all modern fixturing technologies – be it vacuum actuated, mechanical or pneumatic – applied to stand-alone, tester-integrated or inline fixtures.
-
DFT - MG-Products BV
DFT, Designed for Testing. is part of MG-Products and is specialized in the delivery of functional Testfixture solutions from both MG-products and 6TL. DFT also stands for Design For Test, perhaps the most important step in the development process of your product. DFT ensures that your product can be contacted and tested efficiently and reliably.
