Pulsar Microwave Corporation
Pulsar Microwave Corporation, established in 1987, is a U.S.-based manufacturer specializing in high-performance RF and microwave passive components spanning DC to 85 GHz. With full in-house design and manufacturing capabilities, we maintain strict control over quality, performance, and lead times, making us a trusted partner for both standard and custom-engineered solutions.
- 973-779-6262
- 973-779-2727
- sales@pulsarmicrowave.com
- 48 Industrial West
Clifton, NJ 07012
United States of America
-
Product
DC Blocks From 0.1 MHz To 18 GHz
-
Pulsar Microwave Corporation's DC blocks are designed to inner-only topology and utilize our standard housings for fast turn manufacturing. Designs are tested to 50 Ohms, and models range up to 18 Ghz with a maximum voltage rating of 500 Vdc.
-
Product
90 Degree Hybrid Couplers To 500 MHz
-
Hybrid couplers with bandwidths as broad as 125:1 are available for applications within 100 kHz to 500 MHz. Power handling is 1 watt maximum for a load VSWR of 1.2:1 or better. These hybrids have an isolation of 20 dB and phase balance of 3 degrees. Most models have a VSWR of 1.4:1 or better throughout their operating bandwidths.Pulsar Microwave currently offers these hybrid couplers packaged in three outlines, including an SMT version. Standard offering of connectorized packages 412 and 442 are with SMA female connectors. Outline 412 may be customized with any combination of BNC, TNC, F or N connectors. Outline E is the surface mount version and requires less than one square inch of board area, making it well-suited for portable applications.
-
Product
SP6T RF Pin Diode Switches To 12 GHz
-
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
Product
Quad IF Mixers / IQ Demodulators To 16 GHz
-
Quadrature IF Mixers incorporate a 90° hybrid, 2-way 0° divider and two mixers to produce two output signals in phase quadrature (I &Q) when driven by a LO and RF signal.
-
-
Product
6-8 DB Directional Couplers From 0.5 To 40 GHz
-
Pulsar Microwave manufactures the CS06 and CS08 series single directional couplers in nominal values of 6 and 8 dB, respectively. These directional couplers are used in 50-ohm systems for narrow and wideband applications within 500 MHz to 40 GHz. Standard outlines are fitted with SMA or N type female connectors, but Pulsar Microwave can customize upon request.
-
Product
4-Way High Power Combiners To 2200 MHz
-
Pulsar Microwave's high power 4-way combiners cover 5 MHz to 2.2 GHz and handle combined power of 25 to 400 watts. These combiners can combine non-coherent signals unconditionally. They are designed for use in 50-ohm systems, and come standard with SMA or N female connectors.
-
Product
SP4T RF Pin Diode Switches To 16 GHz
-
The 4-way series of absorptive and reflective switches operate from 100 MHz to 16 GHz. They are rated at 200 mW maximum input power and have a switching time of 100 ns. SP4T switches that operate up to 8 GHz have a maximum VSWR of 1.6:1 and minimum isolation of 60 dB. All absorptive and reflective switches manufactured by Pulsar Microwave require both positive and negative 5-volt supplies. Additionally, the TTL control logic operates from 0 to +5 VDC. Voltage connection is made with feed thru terminals. Ground connection is made through the chassis and turret terminals.
-
-
Product
Directional Couplers From 0.01 To 2000 MHz
-
Pulsar Microwave's low frequency directional couplers operate within the frequency range of 10 kHz to 2 GHz. They're available in either surface mount or connectorized designs. SMA female connectors are standard, but BNC, TNC, F, N, jack or plug are available upon request.Most of these directional couplers have a flatness of +/- 0.25 dB and directivity of 20 dB or better within the operating band. VSWR of 1.3:1 or better maintained on all ports for most models. Maximum power handling is between 1 and 3 watts depending on model.
-
Product
Double Balanced Mixers From 0.01 To 6000 MHz
-
A double balanced mixer (DBM) employs the use of a well matched quad-diode ring with two balanced transformers. Because of this, a DBM enjoys the inherent advantage of high port to port isolation. The IF port in Pulsar's DBM design is DC coupled to the diodes.
-
Product
Digital Step Attenuators To 18 GHz
-
This family of digitally controlled switched bit attenuators have standard attenuation ranges of 32 dB and 64 dB, with 8 bits of resolution. LSB of 32 dB models is 0.125 dB, and for 64 dB models LSB is 0.250 dB. Attenuation level is obtained by 8 TTL control inputs.
-
Product
2-Way Power Dividers From 0.23 To 70 GHz
-
Pulsar Microwave manufactures a large selection of 2-way power dividers in narrowband and broadband configurations, covering frequencies from 225 MHz to 70 GHz. They are designed to handle from 10 to 30 watts input power in a 50-ohm transmission system. Microstrip or stripline designs are utilized, and optimized for best performance.Units come standard with SMA or N female connectors, or 2.92mm, 2.40mm, and 1.85mm connectors for high frequency components.
-
Product
Digital Controlled Phase Shifters To 4 GHz
-
Pulsar's Digital Controlled Phase shifters utilize PIN diodes and delay lines to produce the necessary phase requirements. These digital phase shifters use switched lines to obtain temperature stable phase shift. The phase is specified at the center frequency ± 3.0% and is proportional to frequency over the entire band.
-
Product
90 Degree Hybrid Couplers To 600 MHz
-
This category of hybrid dividers features designs from 5 to 600 MHz with 2:1 to 4:1 bandwidth. Maximum insertion loss of 0.5 dB is specified for most units. These 90-degree hybrids are designed for a power rating of 1 watt maximum for a load VSWR of 1.2:1 or better. For use in 50-ohm environments.Pulsar Microwave currently offers this product line in three space-saving packages. The connectorized outline 412 comes standard with SMA female connectors. Outline C is a surface mount package useful for handheld applications with limited PCB area. Outline 301 is hermetically sealed for rugged environments.
