NI

Product

SP200B, 200 MHz, ±60 V, 1X or 10X Attenuation, Single-Ended Passive Oscilloscope Probe

780284-01

-

NI

780284-01 - NI

The SP200B is a standard switchable passive probe for oscilloscopes that provide 1 MΩ input impedance. Depending on the attenuation ratio, the probe has an analog bandwidth of 6 MHz in the 1x attenuation setting or 200 MHz in the 10x attenuation setting.

Product

Serial Interface Device

-

NI

NI

The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.

Product

C Series Multifunction I/O Module

-

NI

NI

The C Series Multifunction I/O Module is a cost-effective, general-purpose I/O module that helps system designers fit more functionality into a single system. The module includes analog input, analog output, and 5 V TTL digital I/O channels. You can use the C Series Multifunction I/O Module with select APIs such as LabVIEW FPGA.

Product

NI-9207, 500 S/s, 16-Channel C Series Voltage and Current Input Module

781068-01

-

NI

781068-01 - NI

500 S/s, 16-Channel C Series Voltage and Current Input Module - The NI‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection.

Product

PXIe-2531 PXI Matrix Switch Module, 256-Crosspoint, Reed Relay, .5 A, 60 V

780587-31

-

NI

780587-31 - NI

512-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXIe‑2531 is a high-density PXI matrix switch module built to serve high‑channel‑count automated test systems. Featuring compact reed relays with switching speeds up to 2,000 cycles/s, the PXIe‑2531 is designed for low‐current, high‐speed switching. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.

Product

PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module

781985-20

-

NI

781985-20 - NI

8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.

Product

NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module

779351-01

-

NI

779351-01 - NI

5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.

Product

NI TB-2642B Terminal Block for NI 2532B as 1-Wire 16x32 Matrix topology With Column Protection Resistors

782385-06

-

NI

782385-06 - NI

The TB-2642B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 1-wire 8x64 matrix. You can directly connect the TB-2642B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2642B also provides optional isolation resistors to protect the reed relays from capacitive loads.

Product

NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle

865683-01

-

NI

865683-01 - NI

NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9205, cDAQ-9171, and cRIO-9940 includes the NI-9205 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9205 features a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Additionally, the NI-9205 provides up to 60 V of overvoltage protection between input channels and common, and it is rated for 1,000 Vrms transient overvoltage protection.

Product

SAEJ1962M-DE9M CAN OBD-II Cable, SAE J1962 to D-sub 9-pos F, 2m

193942-02

-

NI

193942-02 - NI

9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.

Product

NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module

780179-01

-

NI

780179-01 - NI

5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.

Product

cRIO-9033, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, Extended Temperature, 4-Slot CompactRIO Controller

783452-01

-

NI

783452-01 - NI

1.33 GHz Dual-Core CPU, 2 GB DRAM, 8 GB Storage, Kintex-7 160T FPGA, Extended Temperature, 4-Slot CompactRIO Controller - The cRIO-9033 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. You also can use the Mini DisplayPort to add a local human machine interface (HMI) for application development. The cRIO-9033 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, two USB host, one USB device, and two RS-232 serial. Additionally, the cRIO-9033 supports an extended temperate range. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.

Product

USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device

779553-50

-

NI

779553-50 - NI

The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.

Product

PCI-6229, 32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device

779068-01

-

NI

779068-01 - NI

32 AI (16-Bit, 250 kS/s), 4 AO, 48 DIO PCI Multifunction I/O Device - The PCI-6229 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.

Product

BNC-2090A, 16-Channel, 1-Pin Female BNC, 68-Pin Female SCSI, PXI Multifunction I/O Module Terminal Block

779556-01

-

NI

779556-01 - NI

16-Channel, 1-Pin Female BNC, 68-Pin Female SCSI, PXI Multifunction I/O Module Terminal Block - The BNC-2090A is a desktop or rack-mount analog breakout terminal block that you can connect to compatible PXI Multifunction I/O Modules. The terminal block features 16 analog input (AI) BNC connectors for eight differential or 16 single-ended channels. The BNC-2090A also features two analog output (AO) BNC connectors, two user-defined BNC connectors, one analog programmable function input (APFI) BNC connector, one PFI BNC connector, and two 68-pin I/O connectors for DAQ device connection. Additionally, the BNC-2090A features spring terminal block for digital I/O and PFI connections.