NI

Product

sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module

787325-01

Interface Module

NI

787325-01 - NI

Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.

Product

IEC, AC Power Cable

763068-01

Power Adapter

NI

763068-01 - NI

Power Cord, 240V, 10A, North American

Product

PXI-2520, 80-Channel, 2 A, SPST PXI Relay Module

778572-20

Relay

NI

778572-20 - NI

80-Channel, 2 A, SPST PXI Relay Module—The PXI‑2520 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2520 is fully software programmable, and it supports onboard relay count tracking. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.

Product

24-Pin GPIB Male/Female to 24-Pin GPIB Male/Female, Stackable, Double-Shielded GPIB Cable

763061-10

GPIB Cable

NI

763061-10 - NI

The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. This cable features 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. Additionally, the 24M/F-24M/F X2 Cable is available in different lengths.

Product

CB-37FH, 37-Pin DSUB to Screw Terminal Block with Vertical DIN-Rail Mount

778672-01

Terminal Block

NI

778672-01 - NI

37-Pin Female D-SUB to 37-Pin Female Screw Terminal, Vertical DIN Rail Terminal Block - The CB-37FH is an unshielded connector block that provides access to NI data acquisition devices with 37-pin D-SUB connectors. The CB-37FH is a vertical connector block that mounts perpendicular to the DIN rail. It features screw terminals for connecting to 37 I/O signals, 12 to 30 AWG.

Product

External Controller for PXI

External Controller

NI

NI

External Controllers for PXI are rack-mount controllers that feature high-performance multicore processors, up to 4 GB of dual-channel DDR2 RAM, and optional RAID hard-drive configurations for high-speed streaming to disk. These devices offer hot-swappable fans and options for redundant power supplies. The External Controller for PXI is designed for mission-critical, physically demanding applications.

Product

USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device

783200-01

Multifunction Reconfigurable I/O

NI

783200-01 - NI

Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.

Product

PXI-5124 , 150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope

778757-03

Oscilloscope

NI

778757-03 - NI

150 MHz, 200 MS/s, 12-Bit PXI Oscilloscope—The PXI‑5124 high-resolution PXI oscilloscope samples up to 200 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution measurements with up to 150 MHz of analog bandwidth. The PXI‑5124 also features PXI synchronization and data streaming capabilities.

Product

1-Pin MCX Male to 1-Pin SMB Female, 50 Ω Coaxial Cable

188376-01

Coaxial Cable

NI

188376-01 - NI

MCX Male to SMB Female Cable, 50 Ohm, 1 m

Product

NI-9252 , ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module

786782-01

Voltage Input Module

NI

786782-01 - NI

±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a … number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.

Product

USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device

786306-01

CAN Interface

NI

786306-01 - NI

The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.

Product

FD-11614, 16-Channel Temperature Input Device for FieldDAQ

785854-01

Temperature Input Module

NI

785854-01 - NI

The FD-11614 measures up to 16 thermocouple channels. It features cold-junction compensation and open thermocouple detection with an LED indicator per channel to identify disconnected thermocouples. The FD-11614 has an ingress … protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. The FD-11614 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11614 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. This device is ideal for test cell and outdoor environments.

Product

NI-5772, 1.6 GS/s, 12-Bit, 2.27 GHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO

782097-02

Digitizer

NI

782097-02 - NI

The NI‑5772 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that can simultaneously sample two channels at 800 MS/s or sample one channel at 1.6 GS/s with over 2 GHz of analog bandwidth. You can use the NI‑5772 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.

Product

SCB-12, Nano-Pitch Connector Block, 8 SE DIO, 1 QSFP+

787419-01

Connector Block

NI

787419-01 - NI

8-Pin 3.5 mm Pitch Connector to Nano-Pitch I/O, QSFP28 Terminal Block - The SCB-12 converts the Nano-Pitch connector to the industry-standard QSFP28 connector for interfacing I/O signals to plug-in data acquisition. This Terminal Block features the QSFP28 variant of the quad small form-factor pluggable (QSFP) transceiver for high-capacity data communication. The SCB-12 combines with shield cables to provide low-noise signal termination. Additionally, the SCB-12 supports the Nano-Pitch I/O Interconnect System that provides data transfer at 24 Gbps per lane and compatibility with PCI Express, Serial Attached SCSI (SAS), and SATA protocols. The SCB-12 breaks out the NanoPitch connector to a QSFP28 connector as well as an 8-pin connector for general-purpose DIO signals.