Test Electronics
Manufacturers of Electronic Test Equipment, Bed of Nails Test Fixtures, Solder Pallets, and Production Assembly Fixtures
- 831 763 2000
- 909.498.8709
- 821 Smith Road
Watsonville, CA 95076
United States of America
-
Product
High Voltage Surge Current Monitors
HVSCM
-
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
Product
Hi Potential & Cable Continuity Test Fixture
HIPOTCCT
-
The most important features of this hipot tester fixture is its safety and ease of use intuitive control functions and durability in a production environment.
-
Product
Press Down Rods Bed of Nails Testers
RandHDPE HDPE Family
-
HDPE plastic plates for extra easy machine ability and upgradeability. Designed for Research & Development and Pre-Production where product engineering changes are a weekly issue. The primary design focus is easy upgradeability. In R&D and Preproduction, design changes can happen every week. This fixture unlike normal test fixtures was designed to be easily taken apart and updated. Disassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for machining, drilling and wiring updates.
-
Product
Edge Press Technology Bed of Nails Testers
Protector Edge Press Family
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
Press Down Rods Bed of Nails Testers
Protector Press Rods Family
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
Edge Press Technology Bed of Nails Testers
Prober Edge Press Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
Lever Handle Bed of Nails Testers
Automator Manual Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
R&D Clamshell Bed of Nails Testers
Rand Press Rods Family
-
Designed for Research & Development and Pre-Production environments to support often reoccurring product design changes. The primary design focus for this fixture is ease in applying engineering changes and resilience to the abuse of applying multiple engineering changes without damage. In R&D and Preproduction, design changes and updates can occur every week. This Rand fixture, unlike normal test fixtures was designed to be easily taken apart and updated. Constantly disassembling modifying and reassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for multiple updates requiring machining, drilling and wiring changes.
-
Product
Multiple Channel Burn In Power Supply
MCPS
-
The most important features of this burn in power supply is its ability to hold a constant output for each channel even in the event that a unit under test on one channel may short and fail. Since each channel has it''s own transformer, no glitches or voltage spikes can get into any of the other channels. This image shows the results as the second channel from the left is shorted with a small wire and the circuit breaker pops out. Used for burn-in testing and other timed testing where power isolation is required. Very basic simple circuit, see schematic below. Cleans and frees up benchtops, burn in racks and work space clutter. Available in benchtop or rackmount.
-
Product
Cable Continuity Test Fixture
CCT
-
6 and 8 Wire Cable Continuity Test Fixtures For convienient desk top and bench top The most important features of this cable continuity tester is its ease of use intuitive control functions and durability in a production environment.
-
Product
Telephone Headset and Handset Test System
THT
-
TE2000 Headset Tester for audio testing headsets and handsets using computer generated test sounds.
-
Product
Adjustable Press Plate Bed of Nails Testers
Prober Adjustable Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
-
Product
Press Down Rods Bed of Nails Testers
Prober Press Rods Family
-
Production volume test fixture with swappable test plates, front and rear panel inlays, and multi-testing compatibility with process carrier pallets. Swappable test plates provide the ability for one fixture base to support a variety of units under test. Interchangeable front and rear panel inserts provide further customization. Interoperability with process carrier pallets provide multiple board testing capabilities, panelized testing, and flex circuit testing. A selection of interfaces to general testing equipment provide for a wide selection of customized testing features.
