Lumistar Inc.
Lumistar designs and manufactures telemetry products for the flight test and antenna tracking communities. Board level products are manufactured with PCI, PCIe, cPCI bus interfaces as well as continuing support of ISA and VME legacy products. Lumistar products are also available without a PC interface or require an OS to operate. Serial, USB or Ethernet interfaces are used for control. Well documented application software with example code allows users to write their own applications for integration of Lumistar products into their telemetry systems.
- 760-431-2181 x108
- 760-431-2665
- sales@lumistar.net
- 1782 La Costa Meadows
Ste 101
San Marcos, CA 92078
United States of America
-
Product
Airborne Receivers & Bit Synchronizers
-
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
Product
Multi-Channel PCM Processing and Recording System with UDP Streaming
LS-68-M
-
The Lumistar LS-68-M Modular Multi-Channel processing and recording Telemetry Processing System offers an ultra-small, low-cost, high-performance, multi-channel COTS solution for PCM data synchronization, decommutation and simulation applications. Building on the legacy of the Lumistar LS-45, LS-50, LS-55 and LS70 series of products, the LS-68-M enhances the feature sets of each of these product lines and supplies them in a format requiring no hardware drivers in an “OS-less” environment. The LS-68-M utilizes a highspeed Gigabit Ethernet interface for primary controls and data streaming.
-
-
Product
LS-28-1U Chassis Combined AUX Cable Assembly
28U-CBL-AUX3
-
Cable assembly for LS-28-DRSM 1U Rack Mount Unit
-
Product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P, LL/UL/S/C, Programmable Amplitude Balance
LS-16A-R1-24SPLUSC
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
High Performance/Software Controllable RF Multicouplers
-
1U High Performance Rack Mount Broadband Multicouplers, with configurations up to 1×8 or switchable 2×4 configurations. Features include High Output/Output Isolation and Software Controllable power level and amplitude balance.
-
-
Product
Portable Telemetry Systems
-
Lumistar’s portable receivers and test transmitters take the state of the art technology found in the PCI receivers and simulators and install it into a hand held units. Our luggable Telemetry Systems can be configured using our card level products into unique custom solutions.
-
Product
IF Digital Processing Board for Demodulation and Combining
LS-35-R
-
The Lumistar LS-35-R is part of the Lumistar family of digital processing boards used for programmable telemetry systems. The LS-35-R consists of a digital processing main board with two high capacity Xilinx Virtex-5 arrays. The LS-35-R provides a two-channel IF Receiver with Pre/Post detect combining, multimode demodulators with data rates up to 40 Mbps, bit synchronizer outputs, Viterbi decoding, spectral and constellation display, BER reader display and 70 MHz IF modulator with calibratednoise feature. The all-digital design assures a consistent product with high reliability and long-term stability.
-
Product
Tape Up and Down Conversion Board
LS-37-P
-
The IF Digital processing board is a workhorse for all digital demodulation and combing. It can also support other unique functions like sub-carrier demodulation, FM/FM demodulation and tone receiving. Please consult the factory for your unique requirements.
-
Product
Bit Synchronizers, Decoms, and DACs
-
Lumistar offers bit synchronizer boards compatible with the PCI bus, VME bus, and daughter-boards for use with various Lumistar products.
-
Product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/UL/S/C , Programmable Amplitude Balance
LS-16A-R1-24SLUSC
-
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
Product
S-Band Planar Antennas with 8 dBi Gain
LS-08-PS
-
The Lumistar LS-08-PS S-Band Planar Antenna is the ideal companion to the LS-25/27/28 Series Receivers to provide a low cost receiving system with extremely high performance. This small, lightweight antenna is available in various polarizations. The Standard version offers the quickest delivery, but other versions including ones with Polarization Diversity. Combining (dual linear with ±45 slant range) is also available.
-
-
Product
2nd Generation PCI Multi-function Decommutator
LS-50-D
-
The Lumistar LS-50-D PCI Multi-function PCM Decommutator offers a PCM decom, PCM simulator, time code reader/generator, and optional bit synchronizer in a single short PCI card slot. The multi-function decom and simulator are implemented in FPGA using a next generation design based on the LS-50-P. The simulator, decommutator, time code reader and time code generator are achieved on the main board and the bit synchronizer is achieved through an optional low-profile daughterboard. CVSD voice decoding, h.261 video decoding, and IRIG Chapter 8 decoding are achieved through software.
