Bemco Inc.
Our motto is "Focused on Excellence" and that is exactly who we are. The environmental test chambers, space simulation systems, thermal shrouds, fluid chillers, gas conditioners, and many other products we make actually simulate or achieve the environments promised. We take your specifications and requirements literally.
- 805 583 4970
- 805 583 5033
- sales@bemcoinc.com
- 2255 Union Place
Simi Valley, CA 93065
United States of America
-
Product
Right Angle Poppet Valve
PV10
-
We also offer a standard line of both cold traps and right angle poppet valves. Shown at left is a Bemco PV10 Right Angle Poppet Valve and a Bemco MCT12 Round Cold Trap. The cold traps and poppet valves are all stainless steel except for the pneumatic piston. They are available in ASA flange, Conflat, and weld mounting.
-
Product
Humidity Chambers
FW Series
-
The Bemco FW Series of mechanically cooled Glass Door Humidity Chambers have a a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH.. These chambers feature direct dry air injection and direct humidity sensors. They operate without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allow operation at 20% RH at 5 C and 50% RH at -14 C!
-
Product
Compact Temperature Chamber
FB1.5V-UHC Series
-
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
Product
Vertical Thermal Shock Chambers
FSV Series
-
Bemco FSV Series Vertical Thermal Shock chambers are available in two zone (FS2V - hot and cold) and three zone (FS3V hot - cold - hot) versions, with two temperature ranges (-75 C to +200 C or -160 C to +200 C), and two types of cooling systems (all mechanical cooling - no expendable refrigerant required, or all LN2). Very low temperature, -160 C chambers, are always liquid nitrogen cooled. Two zone chambers are offered in four standard sizes, while three zone chambers are offered in three standard sizes.
-
Product
Temperature/Altitude Chambers
AF Series
-
AF Series chambers include a 304 Series stainless steel welded inner pressure liner with high temperature fiberglass insulation. No asbestos is used in chamber construction. The chamber liner is reinforced in accordance with Section VIII (Unfired Pressure Vessels) of the ASME Code.
-
Product
Plug-in Temperature Conditioners
PITC
-
The PITC, with a temperature range of -70 C to +177 C, was first introduced in the late 1950s by Bemcos Conrad/Missimer Division. Today, the modernized version of this system is the ideal solution where short run or infrequent tests are required, test specimens are unusual in size or shape, initial capital costs must be held low, or test needs are frequently changed.
-
Product
High Pressure Gas Conditioners
HPG
-
Bemco HPG, High Pressure Gas Conditioners are similar to the PTS Portable Temperature Conditioners except they are designed for continuous operation at up to two atmospheres (29.4 psia) of pressure. This higher base operating pressure doubles the gas density per cfm of circulating air or gaseous nitrogen allowing the use of smaller connecting tubes while also increasing thermal capability. .
-
Product
High Vacuum Components
HV
-
Bemco's high vacuum components are not just another copy, but are superior solutions for the application. They are precision engineered for a specific application where a more common vendor's part will not do, or they incorporate refinements not yet available in commercial products. A custom liquid nitrogen chevron insert for a trap and an eight inch diameter compound elbow are shown above.
-
Product
Wide Range Individual Bay Chambers
KDZ
-
The Bemco KDZ is similar to the Bemco Kardburn KDR except it has a wider temperature range, a built-in product support system, a latched glass door with a compression gasket, and every bay has it own independent conditioning system, refrigeration package, heaters, and controls.
-
Product
Fluid Distribution Panels
PAO-DII
-
As a further convenience, we offer our PAO-DII Fluid Distribution Panels to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger second generation PAO-II Chiller. You can also use PAO-DII Fluid Distribution panels with any other source of temperature controlled fluid including a Bemco PCL-III Portable Chiller. These systems are individually assembled to match the product being tested.
-
Product
Salt Spray and Fog chamber
P700
-
Bemco's Standard P700 Salt Spray and Fog chamber is designed to fill the needs of laboratories that require accurately controlled salt spray and fog tests on small components and assemblies. This unit meets all standard military, commercial, and ASTM salt fog corrosion and humidity corrosion tests.
-
Product
Walk-in Modular Chambers
FL-M
-
Prefabricated chambers, rooms, and drive-in facilities, made from sectional panels, can be constructed in any size ranging from the very small to the extremely large. They are often a first choice when there is restricted access to the final assembly location or when initial cost is an important consideration. We manufacture a complete line of both prefabricated modular chambers, assembled from sectional panels on site, and welded integral chambers.
-
Product
Burn-in and Stress Screening Chambers
KDR
-
Supervise the operation of your product, electronic device, circuit board, or medical device while they are stress screened, burned-in, or temperature cycled inside a Bemco Kardburn or Koldburn glass front chamber. With a huge amount of testing or storage space within instant reach, KD Chambers provide a compact and attractive alternative to a walk-in chamber.
-
Product
Thermal Shroud
BC8-55/150C
-
When combined with a thermal conditioner such as the Bemco PCL3L-III or PCL3M-III, this shroud converts a 24 inch inside diameter by 30 inch high vacuum only vertical bell jar into a 19 inch inside diameter by 20 inch high thermal vacuum testing system. With a convenient clam shell door, test objects are easily loaded by simply raising the bell jar above the top of the door opening.
-
Product
Universal Test Machine Stands
FTUS
-
Portable, adjustable height, stands are available for all FTU chamber models. They support the chamber without transferring weight to your testing machine. Standard Universal Test Machine stands are furnished with an 18 inch, electrically actuated, lift system, four swivel casters with locks, and an all welded frame. Four types of stands are available
