IRIS Instruments
IRIS Instruments: geophysical equipment for exploring and monitoring the Earth’s resources. IRIS Instruments is one of the world’s leading geophysical equipment manufacturers with four main broadband lines: Resistivimeters, Induced Polarization systems, ElectroMagnetic equipment and Magnetic Resonance.
- +33 2 38 63 81 00
- info@iris-instruments.com
- 1 avenue buffon
Orléans, 45100
France
-
Product
Syscal Pro switch
-
The Syscal Pro is an all-in-one multinode resistivity and induce polarization imaging system for environmental and engineering geophysical studies. The Syscal Pro gathers a 10 channels receiver and a 250W, 2000Vpp internal transmitter which make it the more powerful system of the Syscal range. This system allows to perform up to 10 measurements at a time and its switching board allow to work for 48 (Switch-48) up to 120 (Switch-120) electrodes.
-
Product
Receiver
Elrec 6
-
The Elrec 6 is a 6-channel Induced Polarisation (IP) and Resistivity receiver designed to improve productivity when recording deep profiles and soundings. Beside the classical arithmetic and logarithmic modes, ELREC 6 also offers a Cole-Cole mode and ten fully programmable windows for a higher flexibility in the definition of the IP decay curve.
-
Product
Photon Magnetic Resonance
Numis Poly
-
The Numis Poly device is a Magnetic Resonance Sounding (MRS) system for the direct detection of shallow groundwater down to 150 m of depth
-
Product
Regulated Transmitter
VIP 4000
-
The VIP series of Electrical transmitters are purposely designed for deep induced polarisation or Resistivity sounding investigations. The Vip injects a regulated current into the ground.
-
Product
Photon Magnetic Resonance
Numis Lite
-
The Numis lite device is a Magnetic Resonance Sounding (MRS) system for the direct detection of shallow groundwater down to 50 m of depth.
-
Product
Syscal R2
-
The Syscal R2 unit is a high-power system designed for DC electrical surveys applied to groundwater exploration, environmental studies, civil engineering, structural geology investigation and mineral exploration.
-
Product
Standard Transmitter
Tipix 2200
-
The TIPIX 2200 is a transmitter purposely designed for deep Induced Polarisation or Resistivity sounding investigations. This transmitter is generally used together with V-Fullwavers or Elrec Pro receivers. This entry-level instrument has been designed for an ease of use and for a good productivity together with a strong protection against misuse. This very robust device has proven to be reliable even in very cold weather (up to -40°C) or in wet environment. It is able to inject up to 2200W in the soil and to inject up to 13A, so that it is suitable, even on conductive soils, to measure resistivity and IP at medium range depths. It is powered by standard generator.
-
Product
Standard Transmitter
Tipix 3000
-
The TIPIX 3000 is a transmitter purposely designed for deep Induced Polarisation or Resistivity sounding investigations. This transmitter is generally used together with V-Fullwavers or Elrec Pro receivers.
-
Product
VLF Receiver
T-Vlf
-
The VLF receiver is specially designed for high productivity surveys, in ground water and mining exploration. No orientation of the operator with respect to the direction of the transmitter is required since three magnetic sensors measure the components of the VLF field. Tilt or horizontality of the sensor unit is neither required since two inclinometers correct for tilted position.
-
Product
V-FullWaver
-
The V-FullWaver systems were specifically developed for precise full waveform time domain Induced Polarisation, Resistivity and SP measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording. The V-FullWaver is a dual channel Induced Polarisation, Resistivity and SP receiver. Continually recording at 10ms sample rate provides a full waveform record. It can be synchronized on the GPS PPS signal, allowing an easy process of the signal. Data on the memory can be downloaded directly on a simple USB stick from all the Fullwavers.
-
Product
Syscal R1 Plus
-
The SYSCAL R1 Plus resistivity meter is specifically designed for medium-depth exploration. It combines a power source, transmitter up to a 200W or 800Vpp output voltage, and a 2 channels receiver in a single unit; its compactness makes it an effective tool for intensive resistivity surveys.
-
Product
Full Wave Recorder
I-FullWaver
-
The I-FullWaver systems were specifically developed for precise full waveform time domain induced polarisation, Resistivity and self-potential measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording.
-
Product
Regulated Transmitter
VIP 5000
-
The VIP series of Electrical transmitters are purposely designed for deep Induced Polarisation or Resistivity sounding investigations. The VIP 5000 internal microprocessor is capable of excellent current regulation in almost any load. Predominantly used as part of mineral exploration studies, the VIP series include three systems with different power specifications. This transmitter is generally used together with V-Fullwavers or Elrec Pro receivers.
-
Product
Regulated Transmitter
VIP 10000
-
The VIP series of Electrical transmitters are purposely designed for deep Induced Polarisation or Resistivity sounding investigations.
-
Product
Resistivity Imaging & Sounding System
Syscal Junior Switch
-
The Syscal Junior is an all-purpose resistivity imaging and sounding system for environmental applications. The system can be supplied as a standard imaging system capable of recording two measurements simultaneously. The second recording channel significantly improves data acquisition time when the instrument is fitted with internal switching board for 24 (Switch-24) 48 (Switch-48) or 72 (Switch-72) electrodes for Electrical Resistivity Tomography (ERT).
